2007 HONDA ACCORD SEDAN oil type

If you have the required service
done but do not reset the display, or
reset the display without doing the
service, the system will not show the
proper maintenance intervals. This
canleadtoseriousmechanical
problems because you will no longer
have an accurate record of when
maintenance is needed.
Your authorized Honda dealer
knows your vehicle best and can
provide competent, ef f icient service.However, service at a dealer is not
mandatory to keep your warranties
in effect. Maintenance may be done
by any qualif ied service f acility or
person who is skilled in this type of
automotive service. Make sure to
have the service f acility or person
reset the display as previously
described. Keep all receipts as proof
of completion, and have the person
who does the work fill out the
maintenance record. Check your
warranty booklet f or more
inf ormation.
We recommend the use of Honda
parts and f luids whenever you have
maintenance done. These are
manuf actured to the same high-
quality standards as the original
components, so you can be conf ident
of their performance and durability.
Press the select/reset knob
f or
another 5 seconds. The
maintenance item code(s) will
disappear, and the engine oil lif e
will reset to ‘‘100.’’
4.
CONT INUED
Important Maintenance
Precautions
Maintenance Minder
Maint enance
197

Remove the oil f ilter and let the
remaining oil drain. A special
wrench (available from your
dealer) is required.
Open the hood, and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.
Always change the oil and f ilter
according to the maintenance
messages shown on the inf ormation
display. The oil and f ilter collect
contaminants that can damage your
engine if they are not removed
regularly.
Run the engine until it reaches
normal operating temperature,
then shut it off.
Changing the oil and f ilter requires
special tools and access f rom
underneath the vehicle. The vehicle
should be raised on a service station-
type hydraulic lif t f or this service.
Unless you have the knowledge and
proper equipment, you should have
this maintenance done by a skilled
mechanic.
Make sure the oil f ilter gasket is
not stuck to the engine block. If it
is, remove it bef ore installing a
new oil f ilter.
3.
2.
1.
Changing the Oil and Filter
206
WASHER
4-cylinder models WASHER
V6 models
OIL DRAIN BOLT
OIL DRAIN BOLT

Specif ications
268
µµÎ
Î Î
Î Î
Î Î
Î
Î
Î
Î
Î
Î
Dimensions
Weights Capacities
Air Conditioning
Capacities 189.5 in (4,813 mm)
71.7 in (1,820 mm)
57.2 in (1,453 mm)
HFC-134a (R-134a)
17.6 19.4 oz (500 550 g) 107.9 in (2,740 mm)
61.1 in (1,553 mm)
61.2 in (1,554 mm)
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating See the certification label attached
to the driver’s doorjamb. 4.4 US qt (4.2
)
4.5 US qt (4.3)
4.2 US qt (4.0)
5.6 US qt (5.3
)
5.3 US qt (5.0)
2.0 US qt (1.9)
2.2 US qt (2.1
)
3.1 US qt (2.9
)
3.2 US qt (3.0)
6.9 US qt (6.5)
7.4 US qt (7.0)
2.6 US qt (2.5)
4.8 US qt (4.5)
Engine oil
Manual trans-
mission oil
Automatic
transmission
fluid
Windshield
washer
reservoir
2.3 US qt (2.2
)
2.6 US qt (2.5
)
Excluding the oil remaining in the engine Including the coolant in the reserve tank and that remaining in the
engine
Reserve tank capacity: 0.16 US gal (0.6
)
Refrigerant type
Charge quantity
Lubricant type
ND-OIL8
Fuel tank
Engine
coolant 17.09 US gal (64.7
)
1.35 US gal (5.1
)
1.32 US gal (5.0)
1.77 US gal (6.7)
1.90 US gal (7.2
)
1.88 US gal (7.1)
2.22 US gal (8.4) 6-cylinder models
Approx.
Front
Rear
2:
3:
Change
Manual
Automatic
Total Manual
Automatic Change
Including
filter
Without
filter
Total
Change
Total
Change
Total
U.S.
Canada
1:
2
1
1 3
1
1
1
1
1
1