2007 HONDA ACCORD HYBRID high beam

The U.S. instrument panel is shown. Dif f erences f or the Canadian models are noted in the text.
Instrument Panel
Inst rument s and Cont rols
59
MALFUNCTION
INDICATOR LAMPSUPPLEMENTAL
RESTRAINT SYSTEM
INDICATOR
DOOR AND TRUNK
OPEN MONITOR
LIGHTS ON INDICATOR
SIDE AIRBAG OFF
INDICATOR
CRUISE CONTROL INDICATOR
LOW OIL PRESSURE INDICATOR
IMA SYSTEM
INDICATOR CRUISE CONTROL
MAIN INDICATOR
FUEL ECONOMY INDICATOR SEAT
BELT REMINDER
INDICATOR
VSA ACTIVATION INDICATOR
HIGH BEAM
INDICATOR
ANTI-LOCK BRAKE SYSTEM (ABS) INDICATOR
DAYTIME RUNNING LIGHTS
INDICATOR SECURITY SYSTEM
INDICATOR
CHARGING SYSTEM
INDICATOR
IMMOBILIZER SYSTEM
INDICATOR
TURN SIGNAL
AND HAZARD
WARNING
INDICATORS
AUTO IDLE STOP
INDICATOR PARKING BRAKE AND BRAKE
SYSTEM INDICATOR
LOW FUEL
INDICATOR
TURN SIGNAL AND HAZARD WARNING INDICATORS
ELECTRIC POWER STEERING
(EPS) INDICATOR
MAINTENANCE
MINDER INDICATOR VEHICLE STABILITY ASSIST (VSA)
SYSTEM INDICATOR
(P.61)
(P.62) (P.65)
(P.64) (P.62)
(P.61)
(P.61)
(P.60) (P.60)
(P.63)
(P.63)
(P.66)
(P.65) (P.66)
(P.66)
(P.66)
(P.63) (P.60)
(P.65)
(P.60) (P.63)
(P.60)
(P.64) (P.64)
(P.65) (P.62)
06/08/08 14:25:47 31SDR620_064

This indicator comes on when the
security system is set. See pagef or more inf ormation on the
security system. This indicator comes on with the
high beam headlights. For more
inf ormation, see page .
When the daytime running lights
(DRL) are on, this indicator comes
on with reduced brightness.
If this indicator comes on when the
ignition switch is turned to the ON
(II) position and the parking brake is
released, it means there is a problem
in the high beam headlight’s circuit.
Have your vehicle checked by your
dealer.
146 77
Security System Indicator High Beam Indicator
Daytime Running L ights
Indicator
Instrument Panel Indicators
64
SECURITY SYSTEM INDICATOR
06/08/08 14:26:48 31SDR620_069

µµPush down on the
lef t lever to signal a lef t turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever in
the proper direction and hold it. The
lever will return to center when you
release it or complete a turn.
Turn signal
Of f
Parking and interior lights
Headlights
High beams
Flashhighbeams Turning the
switch to the ‘‘ ’’ position turns
on the parking lights, taillights, side-
marker lights, and rear license plate
lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights.
When the light switch is in the
‘‘ ’’ or ‘‘ ’’ position, the
lights on indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position. If you leave the lights on with the
key removed f rom the ignition
switch, you will hear a reminder
chime when you open the driver’s
door.
To f lash the high beams, pull the
lever back lightly, then release it.
The high beams will stay on as long
as you hold the lever back.
1.
2.
3.
4.
5.
6. Turn Signal and Headlights Turn Signal
Headlights On
Turn Signals and Headlights
76
06/08/08 14:28:56 31SDR620_081

µIf you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the door,
the lights will turn of f af ter 10
minutes.
The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights-on
reminder chime.
To turn on the high
beams, push the lever f orward until
you hear a click. The blue high beam
indicator will come on (see page ).
To turn of f the high beams, pull the
lever back. To flash the high beams,
pull the lever f arther back, and then
release it. The high beams remain on
until the lever is released. This f eature turns of f the headlights,
parking lights, side marker lights,
taillights, and rear license plate lights
within 15 seconds of removing the
key f rom the ignition switch and
closing the driver’s door.
This feature activates if you leave
the headlight switch in the or
position, remove the key, then
open and close the driver’s door.
64
Automatic Lighting Of f Feature
High Beams
Turn Signals and Headlights
Inst rument s and Cont rols
77
06/08/08 14:29:05 31SDR620_082

With the headlight switch off, the
high beam headlights and the high
beam indicator come on with
reduced brightness when you turn
the ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.The instrument panel will illuminate
with reduced brightness when you
open the driver’s door. The
brightness will increase slightly
when you insert the key in the
ignitionswitch,thengotonormalbrightness when you turn the
ignition switch to the ON (II)
position.
The Select/Reset knob on the
instrument panel controls the
brightness of the instrument panel
lights. Turn the knob to adjust the
brightness. If you do not insert the key in the
ignition switch af ter opening the
driver’s door, the illumination turns
of f about 30 seconds af ter you close
the door.
To reduce glare at night, the instru-
ment panel illumination dims when
you turn the light switch to or
. Turning the Select/Reset
knob f ully to the right until you hear
a click will cancel the reduced bright-
ness. If you insert the key but do not turn
the ignition switch to the ON (II)
position, the illumination turns of f in
about 10 seconds.
Instrument Panel Brightness
Daytime Running L ights
Turn Signal and Headlights, Instrument Panel Brightness
78
SELECT/RESET KNOB
06/08/08 14:29:16 31SDR620_083

Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.Push the electrical connector onto
the bulb.
Turn on the headlights to test the
new bulb.
Open the hood. To change a bulb
on the driver’s side, undo the two
f asteners and remove the air
intake cover. Reinstall the air intake cover.
Reinstall the two fasteners and
secure them by pushing on the
heads until they lock.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
Install the new bulb, and turn it
one-quarter turn clockwise to lock
it in place.
1. 3.
2.
4.5.
6.
7.
High Beam Headlight
Lights
214
AIR INTAKE
COVER
FASTENERS TABBULB
06/08/08 14:50:50 31SDR620_219