2007 HONDA ACCORD HYBRID display

To load or play CDs, the ignition
switch must be in the ACCESSORY
(I) or the ON(II) position.To listen to satellite radio when a CD
is playing, press the CD/AUX XM
button.
You operate the CD changer with
the same controls used f or the radio.
To select the CD changer, press the
CD button. The numbers of the disc
andtruckplayingareshowninthe
display. On vehicles with navigation
system, these numbers also appear
in the upper display. The system will
continuously play a disc until you
change modes. To play the radio when a CD is
playing, press the AM/FM button.
Press the CD button again to switch
back to the CD player.
To play a tape when a CD is playing,
insert a tape in the player (optional).
If a tape is in the player, press the
CD/AUX button. Press the CD/AUX
button again to switch back to the
CD player.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f .
For vehicles with Satellite RadioTo Play a CD
Playing a CD, CD Changer
126
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.
06/08/08 14:37:21 31SDR620_131

µµ´
Û
Ý
You can also load a CD into an empty
position while a CD is playing. Select
the empty position (the disc number
indicator is not highlighted) and
press the appropriate preset bar or
touch a disc icon. The current CD
stops playing and starts the loading
sequence. The CD just loaded will
play. To select a dif f erent disc, press the
appropriate side of a preset bar
(1 6) or use the Preset 5 (DISC )
to select the previous disc or Preset
6 (DISC ) to select the next disc in
sequence. On vehicles with
navigation system, touch the
appropriate disc icon or press the
or side of the CH/DISC bar. If
youselectanemptypositioninthe
CD changer, the system will try to
load the CD in the next available slot.
Repeat steps 1 through 3 until all
six positions are loaded. If you are
not loading all six positions, the
system begins playing the last CD
loaded. When the CD load indicator turns
green and ‘‘LOAD’’ appears in the
screen again, insert the next CD in
the slot. Insert the disc into the CD slot
when the green CD load indicator
comes on. Insert it only about
half way; the drive will pull it in the
rest of the way. You will see
‘‘BUSY’’ on the display as the CD
load indicator turns red and blinks
as the CD is loaded. The disc number f or an empty
position is highlighted and the red
light starts blinking. Press and hold the LOAD button
until you hear a beep and see
‘‘LOAD’’ in the display, then
release the button.
1.
2.
3.
4.
5.
CONT INUED
Playing a CD, CD Changer
L oading CDs in the In-dash CD
Changer
Features
127
06/08/08 14:37:31 31SDR620_132

µ
µ µ µ
µ
µ µ
µ
Push the to
play the next track on the disc. Push
the oncetoreplaythetrackin
play; press it twice to replay the
previous track. To move rapidly
within a track, press and hold the or button.
Press the RPT button
to continuously replay a track. You
will see RPT in the display. Press the
RPT button again to turn it off.
To continuously
replay the current CD, press and
hold the RPT button for about a
second. You will see D-RPT in the
display. The system switches to the
normal repeat mode when you press
the RPT button during the disc
repeat mode. Press the RDM
button to play the tracks in random
order. You will see RDM in the
display. Press the RDM button again
to return to normal play.
The SCAN f unction
samples all the tracks on the
selected disc in the order they are
recorded. To activate it, press and
release the SCAN button. You will
see SCAN in the display, and you will
get a 10 second sampling of each
track on the selected CD. Press the
SCAN button again to get out of scan
mode.
When you press and
hold the SCAN button for more than
2 seconds, the system gives you a 10
second sampling of the f irst track on
each disc in the in-dash CD changer.
You will see D-SCAN in the display.
Touch the SCAN button again to get
out of disc scan mode. When you
touch the TRACK REPEAT icon on
the audio display, the system
continuously plays the same track.
You will see REPEAT beside the
track inf ormation on the audio
screen, and RPT in the upper display.
Press the icon again to get out of
track repeat mode.
When you touch
the DISC REPEAT icon on the audio
display, the system continuously
replays the current CD. You will see
REPEAT beside the disc inf ormation
on the audio screen, and D-RPT in
the upper display. Touch the icon
again to get out of disc repeat mode. To use the controls, press the
AUDIO button; the control icons will
appear on the screen.
On vehicles without navigation system On vehicles with navigation system
Playing a CD, CD Changer
SEEK /SK IP
REPEAT
DISC REPEATRANDOM
SCAN
DISC SCAN
T RA CK REPEA T
DISC REPEAT
128
06/08/08 14:37:44 31SDR620_133

µµ µWhen you touch
this icon on the audio display or
press the SCAN button, you will get
a10secondsamplingof eachtrack
on the current CD. You will see
SCAN beside the track inf ormation
on the audio screen, and SCAN in
the upper display. Press the icon or
button again to get out of track scan
mode. When you touch the
DISC SCAN icon on the audio
display, or press and hold the SCAN
button for more than 2 seconds, the
system gives you a 10 second
sampling of the f irst track on each
disc in the in-dash CD changer. You
will see SCAN beside the disc
inf ormation on the audio screen, and
D-SCAN in the upper display. The
system switches to the track scan
mode when you press the SCAN
button. To get out of disc scan mode,
touch the icon again, or press and
hold the SCAN button for more than
2 seconds. When you
touch the TRACK RANDOM icon on
the audio display, the system plays
the tracks on the current CD in
random order. You will see
RANDOM beside the track
inf ormation on the audio screen.
Press the icon again to get out of
track random mode.
Playing a CD, CD Changer
T RA CK SCA N DISC SCA N T RA CK RA NDOM
Features
129
06/08/08 14:37:49 31SDR620_134

To remove a dif f erent disc f rom the
changer,firstselectitwiththe
appropriate preset bar or icon. When
that CD begins playing, press the
eject button. Continue pressing the
EJECT button to remove all the discs
f rom the changer.
To remove all the discs in the
changer in a sequence, press and
hold the eject button for about 2
seconds.
To play a tape when a CD is playing,
insert a tape in the player (optional).
If a tape is in the player, press the
CD/AUX button. Press the CD/AUX
button again to switch back to the
CD player.
If you turn the system of f while a CD
is playing, the CD will stay in the
drive. When you turn the system
back on, the CD will begin playing
where it lef t of f .
Press the eject button ( ) to
remove the CD. If you eject the CD,
but do not remove it f rom the slot,
the system will automatically reload
the CD af ter 15 seconds and put it in
pause mode. To begin playing, press
the CD button.
PresstheAM/FMorCD/AUX/XM
button to switch to the AM/FM
radio or satellite radio while a CD is
playing. To play the CD, press the
CD/AUX/XM button again. To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJECT’’ in the display.
When you press the eject button, the
system switches to the previous
mode (AM/FM radio, satellite radio
(U.S. models), or tape player
(optional)).
Playing a CD, CD Changer
Removing CDs f rom the Changer
To Stop Playing a CD
130
06/08/08 14:37:58 31SDR620_135

Error Message CauseSolution
Thechartontherightexplainsthe
error messages you may see in the
display while playing a disc.
If you see an error message in the
display while playing a disc, press
the eject button. After ejecting the
disc, check it for damage or
deformation. If there is no damage,
insert the disc again.
If there is still a problem, the error
message will appear again. Press the
eject button, and pull out the disc.
Insert a dif f erent disc. If the new
disc plays, there is a problem with
the f irst disc. If the error message
cycle repeats and you cannot clear it,
take your vehicle to a dealer.
FOCUS Error
Mechanical Error
High Temperature Press the eject button and pull out the disc.
Check if the disc is inserted correctly in the CD
player.
Make sure the disc is not scratched or damaged.
Press the eject button and pull out the disc.
Check the disc for damage or deformation.
If the CD cannot be pulled out or the error
indication does not disappear after the disc is
ejected, see your dealer.
Do not try to force the disc out of the player.
Will disappear when the temperature returns to
normal.
or
or
CD Player Error Messages
Features
131
06/08/08 14:38:09 31SDR620_136

Playing a T ape (U.S. Vehicles)
Features
133
PWR/VOL KNOBAUDIO
DISPLAY
BUTTON
SEEK BAR
SEEK BAR RPT INDICATOR TAPE DIRECTION
INDICATOR
PWR/VOL
KNOBRPT INDICATOR TAPE DIRECTION INDICATOR
CH/DISC
BAR
PRESET BARS
(U.S. model shown) (U.S. model shown)
TAPE
DIRECTION
ICONS
NR ICON
CD/AUX XM
BUTTON
CD/AUX XM
BUTTON
RPT
BUTTON UPPER
DISPLAY
REPEAT ICON
Without navigation system With navigation system
06/08/08 14:38:30 31SDR620_138

Î
Î
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Make sure the open side of the tape
is facing right, then insert the tape
most of the way into the slot. The
system will pull the tape in the rest
of the way, and begin to play it.Dolby noise reduction turns on
when you insert a tape. The
indicator will light in the
display. If the tape was not recorded
in Dolby, turn it of f by pressing the
Preset 4 (NR) side of the preset bar
or touching the NR icon. Dolby
remains of f until you press the
preset bar or the icon again.
The tape direction indicator will
show you which side of the tape is
playing. If you want to play the other
side, press the Preset 3 (PLAY/
PROG) side of the preset bar, or
press the AUDIO DISPLAY button
and then touch the appropriate tape
direction icon. When the player
reaches the end of the tape, it will
automatically reverse direction and
play the other side. To remove the tape, press the eject
button. If you want to turn the player
off, press the PWR/VOL knob or
turn off the ignition. The tape will
remain in the drive. When you turn
the system back on, the tape will
begin playing where it lef t of f .
To switch to the AM/FM radio,
Satellite Radio, or CD changer while
a tape is playing, press the AM/FM
or CD/AUX XM button. To change
back to the tape player, push the
CD/AUX XM button.
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing
Corporation. ‘‘DOLBY’’ and the double-D
symbol are trademarks of Dolby
Laboratories Licensing Corporation.
Optional on all U.S. models
To Play a Tape To Stop Playing a Tape
Playing a T ape (U.S. Vehicles)
134
06/08/08 14:38:38 31SDR620_139