2007 GMC SAVANA bulb

Rear Axle
............................................. 331
Front Axle
............................................ 331
Noise Control System
........................... 332
Bulb Replacement
................................ 334
Windshield Wiper Blade
Replacement
..................................... 338
Tires
..................................................... 340
Appearance Care
.................................. 377
Vehicle Identification
............................. 386
Electrical System
.................................. 387
Capacities and Specifications
................ 393Maintenance Schedule
.............................. 395
Maintenance Schedule
.......................... 396
Customer Assistance Information
............. 417
Customer Assistance and
Information
........................................ 418
Reporting Safety Defects
...................... 436
Index
.......................................................... 439
2

•LWindshield Washer. SeeWindshield
Washer on page 150.
•ICruise Control.Cruise Control on
page 151.
For information on the exterior lamps, seeExterior
Lamps on page 154later in this section.
Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever will
return automatically.
An arrow on the
instrument panel cluster
will flash in the
direction of the turn or
lane change.To signal a lane change, just raise or lower the
lever until the arrow starts to flash. Hold it
there until you complete your lane change. The
lever will return by itself when you release it.
If you move the lever all the way up or down, and
the arrow flashes at twice the normal rate, a
signal bulb may be burned out and other drivers
may not see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when
you signal a turn, check for burned-out bulbs or a
blown fuse. SeeFuses and Circuit Breakers on
page 387.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a
mile (1.2 km), a chime will sound at each flash
of the turn signal. To turn off the chime, move the
turn signal lever to the off position.
148

Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle has to have
extra wiring and a heavy-duty turn signal
flasher (included in the optional trailering package).
The arrows on your instrument panel will flash
whenever you signal a turn or lane change.
Properly hooked up, the trailer lamps will also flash,
telling other drivers you’re about to turn, change
lanes or stop.
When towing a trailer, the arrows on your
instrument panel will flash for turns even if the bulbs
on the trailer are burned out. Thus, you may think
drivers behind you are seeing your signal when
they are not. It’s important to check occasionally to
be sure the trailer bulbs are still working.
Driving On Grades
Reduce speed and shift to a lower gearbefore
you start down a long or steep downgrade. If you
don’t shift down, you might have to use your
brakes so much that they would get hot and no
longer work well.
You can tow in DRIVE (D). You may want to shift
the transmission to THIRD (3) or a lower gear
under heavy loads and/or hilly conditions.
When towing at high altitude on steep uphill grades,
consider the following: Engine coolant will boil at a
lower temperature than at normal altitudes. If you
turn your engine off immediately after towing at high
altitude on steep uphill grades, your vehicle may
show signs similar to engine overheating. To avoid
this, let the engine run while parked (preferably on
level ground) with the automatic transmission in
PARK (P) for a few minutes before turning the
engine off. If you do get the overheat warning, see
Engine Overheating on page 309.
280

Noise Control System................................. 332
Tampering with Noise Control System
Prohibited.............................................. 332
Bulb Replacement....................................... 334
Halogen Bulbs........................................... 334
Headlamps................................................ 334
Front Turn Signal, Sidemarker and
Parking Lamps....................................... 336
Center High-Mounted Stoplamp (CHMSL) ... 336
Taillamps................................................... 337
Replacement Bulbs................................... 338
Windshield Wiper Blade Replacement....... 338
Tires............................................................ 340
Tire Sidewall Labeling............................... 341
Tire Terminology and Definitions............... 345
Inflation - Tire Pressure............................. 348Dual Tire Operation................................... 350
Tire Inspection and Rotation...................... 351
When It Is Time for New Tires.................. 353
Buying New Tires...................................... 353
Different Size Tires and Wheels................ 355
Uniform Tire Quality Grading..................... 356
Wheel Alignment and Tire Balance............ 357
Wheel Replacement.................................. 357
Tire Chains............................................... 359
If a Tire Goes Flat.................................... 360
Changing a Flat Tire................................. 360
Removing the Spare Tire and Tools.......... 362
Removing the Flat Tire and Installing
the Spare Tire....................................... 365
Secondary Latch System........................... 371
Storing a Flat or Spare Tire and Tools...... 375
Spare Tire................................................. 376
Section 5 Service and Appearance Care
284

Bulb Replacement
For the proper type of replacement bulbs, see
Replacement Bulbs on page 338.
For any bulb changing procedure not listed in this
section, contact your dealer.
Halogen Bulbs
{CAUTION:
Halogen bulbs have pressurized gas
inside and can burst if you drop or
scratch the bulb. You or others could be
injured. Be sure to read and follow the
instructions on the bulb package.
Headlamps
To remove the headlamp assembly from the
vehicle and access the bulbs, do the following:
1. Open the hood. SeeHood Release on
page 295for more information.
2. Remove the two bolts from the headlamp
assembly.
3. Remove the two pins on the top of the
headlamp assembly. To remove the pins, turn
the outer pin clockwise and pull it straight
up. To remove the inner pin, turn it
counterclockwise and pull it straight up.
334

4. Lift the inboard side of the headlamp to
release the inboard tab from the radiator
support.
5. Lift the outboard side of the headlamp to
release the outboard tab from the radiator
support.
6. Lower the headlamp to allow the vertical
adjustor to clear the tie bar.
7. Turn the headlamp forward and upward to
remove it from the grille.
8. Turn the bulb connector counterclockwise and
pull it out of the housing.
9. Without removing the headlamp assembly
itself, remove the bulb socket from the back
of the headlamp on the driver’s side.
10. Turn the bulb counterclockwise one quarter
turn to remove it from the socket.
11. On the passenger’s side, turn the bulb
clockwise one turn.12. Install the new bulb into the socket then
reinstall it into the headlamp assembly.
13. Reverse the steps to reinstall the headlamp
assembly.
335

Front Turn Signal, Sidemarker and
Parking Lamps
To replace the front turn signal, sidemarker and/or
parking lamp bulb(s), do the following:
1. Use a small tool to unlatch the outboard clip
on the lamp.
2. Pull the lamp forward to completely unlatch
the clip. Move the lamp outboard to loosen
the tabs.3. Remove the lamp from the grille.
4. Squeeze the tab on the side of the bulb
socket while turning it counterclockwise.
5. Remove the bulb socket from the back of the
lamp assembly.
6. Replace the bulb.
7. Turn the bulb socket clockwise to reinstall it in
the lamp assembly.
Center High-Mounted
Stoplamp (CHMSL)
The center high-mounted stoplamp (CHMSL) is
located above the rear doors at the center of
the vehicle.
336

To replace a bulb, do the following:
1. Remove the two screws from the CHMSL
assembly.
2. Remove the assembly.
3. Turn the bulb counterclockwise one quarter
turn to remove it from the socket.
4. Install a new bulb.
5. Reverse the steps to reinstall the assembly.
If items are loaded on the roof of the vehicle, as in
a luggage carrier, care should be taken not to
block or damage the center high-mounted
stoplamp unit.Taillamps
To replace one of these bulbs, do the following:
1. Remove the
two inboard nuts
from the inside
of the taillamp
assembly.
2. Pull the taillamp assembly rearward to clear
the studs.
3. Slide the taillamp assembly slightly upward to
release the lower clip.
4. Remove the three nuts on the taillamp
assembly.
5. Remove the taillamp assembly from the
vehicle.
337