11
ENTERTAINMENT
Audio SystemsLoad one CD into the Six Disc
CD Player
1. With the ignition on, press andrelease the LOAD side of the LOAD
CD button.
2. Wait for the indicator light at the right side of the slot to turn green.
3. Insert the disc partway into the slot, label side up; the player will pull the
disc in.
Multiple Disc CD Player
(if equipped)
• Press the H or HR button until the correct hour appears on the display.
• Press and hold the M or MIN button until the correct minute appears on
the display.
The time may be set with the ignition on
or off.
Set the time with an FM station’s
Radio Data System (RDS) setting
(if equipped)
• Press and hold both HR and MN for two seconds until UPDATED and the
clock symbol appear on the display.
• If the time is not available from the station, NO UPDAT appears in the
display.
Program radio station presets
1. Turn the radio on.
2. Press the BAND button to select theband (AM/FM1/FM2/XM1/XM2).
3. Use the seek or tune knob to tune in the desired station.
4. Press AUTO EQ to select the equalization that best suits the type
of station selected.
5. Press and hold one of the six numbered pushbuttons until a beep
sounds; release the button.
6. Repeat these steps for each station preset, using a different numbered
button for each station.
Display a station’ s INFO message
when INFO appears on the display
• Press INFO to see the message.
Once the complete message has been displayed, INFO disappears
from the display.
Tune to an RDS broadcast of a
selected program type
1. Press the TYPE button to select the
Program Type you want to listen to.
2. Press the or button.
Access one of the two available XM
Satellite Radio bands (if equipped)
• Press the BAND button until XM1 or XM2 appears on the display.
MP3 Radio (if equipped)
A CD R or CD RW containing MP3
audio tracks will play automatically when
inserted into the CD/MP3 player.
See Section 3 of your Owner Manual.
Getting to Know YourEnvoy16
PERFORMANCE & MAINTENANCE
Malfunction Indicator Lamp
(Service Engine Soon Lamp)
This instrument panel cluster lamp
illuminates under a variety of conditionswhen the On Board Diagnostics II (OBDII) system detects a malfunction in the
vehicle’s emission controls.
If the Malfunction Indicator Lamp
is lit steadily, check the gas cap toensure it is present and securely fastened
• Turn the cap clockwise until a ratch
eting sound is heard, signaling that itis secure.
•If this is the cause of the condition, a
few driving trips with the cap installedproperly should turn the light off.
See Section 3 of your Owner Manual.
Electronically Controlled
Air Suspension (if equipped)
Occasional whirring and/or hissing
sound under the rear of the vehicle
• This sound indicates that the sys
tem’s air compressor is operating to
provide a level ride height, and is normal.
See Section 4 of your Owner Manual.
Air Inflator System (if equipped)
Locate the air
inflator unit and kit
The inflator unit is in
the rear compart
ment on the pas senger side of thevehicle, behind an
access cover.
An inflator kit, with a
22 foot hose and three nozzle adapters,is located in the glove box.
Use the air inflator
1. Open the access cover.
2. Attach the appropriate nozzle adapter
to the end of the hose (if required).
3. Attach that end of the hose to the
object you are inflating. Attach theother end of the hose to the inflatoroutlet.
4. Press and release the on/off switch
to turn the air inflator on. An indicator
light verifies that the inflator is
running.
5. When inflation is complete, press and
release the on/off switch again.
6.Remove the hose from the outlet
(load leveling will not operate when
the hose is attached to the outlet).
See Section 5 of your Owner Manual.
