2007 FORD FIESTA engine

21 1 -02-3 Power Steering 2 1 1 -02-3
SPECIFICATIONS
2006.0 Fiesta 12/2006 G105647en
Description
Power steering fluid reservoir retaining screws
-
vehicles with 2.OL Duratec-HE (M14)
Steering gear to power steering fluid reservoir return
line support bracket to generator retaining nut
-
vehicles with 2.OL Duratec-HE (M14)
Tie-rod end retaining nut
Steering column shaft to steering gear pinion
retaining bolt
Exhaust heat shield to steering gear retaining bolts
Exhaust flexible pipe to muffler and tailpipe
assembly retaining nuts
- vehicles with I .6L
Duratorq-TDCi (DV) Diesel
Stabilizer bar link. to stabilizer bar retaining nut
Front crossmember rear retaining bolts
Front crossmember inner and outer retaining bolts
Front crossmember front retaining bolts
Engine support insulator retaining bolts Ib-in
80
-
-
-
-
-
-
-
-
-
-
Nm
9
11
48 28
14
47
48
115
175 70
48
I b-ft
-
8
35
21
10
35
35
85
129
52
35
procarmanuals.com

21 I -02-9 Power Steering 21 1-02-9
REMOVAL AND INSTALLATION
Discard the O-ring seal. 1. Push the O-ring seal onto the special tool.
2. Locate the special tool onto the union and
install the O-ring seal.
5. Detach the power steering line bracket from I TIE001 5852
the engine block.
2. N0TE:Make sure the collar on the hose is
inserted fully into the quick release coupling.
To install, reverse the removal procedure.
3. Fill and bleed the power steering system.
For additional information, refer to: Power
Steering System Filling
(211 -00 Steering
System
- General Information, General
Procedures)
I Power Steering System Bleeding (211-00
Steering System - General Information,
General Procedures).
6. Remove the power steering pump.
Installation
1. N0TE:H installing a new power steering
pump, the power steeing pressure line union
supplied with the new pump should be
removed and retained for further use.
Using the special tool, install a new O-ring
seal onto the power steering line to power
steering pump union.
2006.0 Fiesta 1212006 ~397031 en
procarmanuals.com

21 1-02-1 8 Power Steering 21 1-02-1 8
REMOVAL AND INSTALLATION
5. N0TE:Note the position of the power steering
line to aid installation.
Detach the power steering line bracket from
the engine block.
I
Detach the power steering line bracket from
the steering gear.
/-.
Right-hand drive vehicles
9. N0TE:Note the position of the power steering
6. Disconnect the power steering pressure line to aid installation.
(PSP) switch electrical connector.
Detach the power steering line bracket from
the steering gear.
Left-hand drive vehicles
7. Detach the steering gear return hose from
the pressure line.
8. N0TE:Note the position of the power steering
line to aid installation.
All vehicles
10. Disconnect the power steering lines from
the steering gear valve body.
1. Remove the retaining bolt.
2. Rotate the clamp plate.
Allow the fluid to drain into a suitable
container.
2006.0 Fiesta 1212006 G397028en
procarmanuals.com

21 1 -02-25 Power Steering 21 1 -02-25
REMOVAL AND INSTALLATION
Remove the exhaust hanger insulator. 11. Remove the front axle crossmember
retaining bolts on both sides.
8. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
12. Lower the front axle crossmember
Detach the stabilizer bar link from the approximately
100 mm.
stabilizer bar on both sides.
13. Detach the steering gear to power steering
fluid reservoir return line from the power
steering pump to steering gear pressure
line.
9. Remove the engine support insulator.
10. Using a transmission jack and a wooden
block, support the front axle crossmember.
14' ~CAUTION:C~~ the steering gear valve
body inlet port and outlet port to prevent
fluid loss or dirt ingress.
Disconnect the power steering lines from the
steering gear valve body.
1. Remove the power steering lines clamp plate
retaining bolt.
2. Rotate the power steering lines clamp plate.
2006.0 Fiesta 1212006 G458165en
procarmanuals.com

21 1-02-27 Power Steering 21 1 -02-27
REMOVAL AND INSTALLATION
Using the transmission jack, wooden block 7.
Install the front axle crossmember rear inner
and the special tool, position and align the retaining
bolts on both sides.
front axle crossmember.
8. Lower and remove the transmission jack and
5m &AUTION:W~~I~ tightening the front axle the
wooden block.
crossmember front retaining bolt and the
9. Install the engine support insulator.
front axle crossmem ber rear outer retaining
bolts, make sure that the front axle
crossmember does not move.
Install the front axle crossmember front
retaining bolt and the front axle
crossmember rear outer retaining bolts on
both sides.
i,
6. Remove the front axle crossmember rear
inner retaining bolts and the special tools.
10. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
Attach the stabilizer bar link to the stabilizer
bar on both sides.
~CAUTION:T~~~ care when installing the
exhaust hanger insulator to prevent
damage.
2006.0 Fiesta 1212006 G458165en
procarmanuals.com

21 1 -02-33 Power Steering 21 1-02-33
REMOVAL AND INSTALLATION
Ifem 5 Cable ties Remove
the exhaust hanger insulator.
I I CAUTION:^^^^ bending of the exhaust
flexible pipe may cause damage resulting in
failure.
Support the exhaust flexible pipe with a
support wrap or splint.
*' n~A~T10~:Twistin~ the exhaust flexible
pipe more than two degrees may cause
damage resulting in failure.
, N0TE:Use a pry-bar to prevent the exhaust flexible
( , pipe from twisting when removing the catalytic
converter to muffler and tailpipe assembly retaining
nuts.
Remove the exhaust flexible pipe to catalytic
converter retaining nuts.
4. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
Detach the stabilizer bar link from the
stabilizer bar on both sides.
Discard the exhaust flexible pipe to catalytic
converter gasket and retaining nuts.
5. Remove the engine support insulator.
3m ~CAUTION:T~~~ care when removing the 6. Using a transmission jack and a wooden
exhaust hanger insulator to prevent damage.
block, support the front axle crossmember.
2006.0 Fiesta 1212006 G458167en
procarmanuals.com

21 1 -02-36 Power Steering 21 1 -02-36
REMOVAL AND INSTALLATION
4. Remove the front axle crossmember rear Attach the stabilizer bar link to the stabilizer
inner retaining bolt and the special tool on
bar on both sides.
both sides.
9m &~uTl~~:Twistin~ the exhaust flexible 5. Install the front axle crossmember rear inner pipe more than two degrees may cause retaining bolts on both sides.
damage resulting in failure.
N0TE:Use a pry-bar to prevent the exhaust flexible
pipe from twisting when installing the exhaust
flexible pipe to catalytic converter retaining nuts.
N0TE:lnstall a new exhaust flexible pipe to
catalytic converter gasket and retaining nuts.
Install the exhaust flexible pipe to catalytic
converter retaining nuts.
6. Lower and remove the transmission jack and
wooden block.
7. Install the engine support insulator.
8. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
lo' ~CAUTION:T~~~ care when installing the
exhaust hanger insulator to prevent
damage.
N0TE:Check the exhaust hanger insulator for
damage. lnstall a new exhaust hanger insulator if
required.
2006.0 Fiesta 12/2006 G458167en
procarmanuals.com

2 1 1 -02-39 Power Steering 21 1-02-39
REMOVAL AND INSTALLATION
Support the exhaust flexible pipe with a Vehicles with diesel engine
support wrap or splint.
i 8. Detach the exhaust flexible pipe from the
muffler and tailpipe assembly.
&AUTION:T~~~ care when removing the
exhaust hanger insulator to prevent damage.
Discard the exhaust flexible pipe to muffler
and tail pipe assembly retaining nuts.
Remove the exhaust hanger insulator. Vehicles with 2.OL engine
9. Detach the exhaust flexible pipe from the
catalytic converter.
Discard the exhaust flexible pipe to catalytic
converter gasket and retaining nuts.
Vehicles with 1.25L, 1.4L or 1.6L engine
7. Detach the exhaust flexible pipe from the
catalytic converter.
Discard the exhaust flexible pipe to catalytic
converter gasket and retaining nuts.
All vehicles
On &AUTION:L~~~~ the tie-rod end retaining
nuts in place to protect the ball joint studs.
N0TE:Use a 5 mm Allen key to prevent the ball
joint stud from rotating.
2006.0 Fiesta 1212006 GI 05648en
procarmanuals.com