2007 FORD FIESTA timing belt

,303-01 B-6 Engine - 2.OL Duratec-HE (M14) 303-01 B-6
SPECIFICATIONS
I Description I Nm' I Ib-ft I Ib-in I
Evaporative emission (EVAP) valve retaining
bracket retaining nut and bolt
Valve cover retaining bolts
I 10 I - I 89 I
Cylinder block blanking plug
Coolant pump pulley retaining bolts
Coolant pump retaining bolts
Oil level indicator and oil level indicator tube upper
retaining bolt
Oil level indicator and oil level indicator tube lower
retaining bolt 20
25
10
Oil pressure switch I 15 I 11 I - I
I Oil pan retaining bolts
15
18
-
-
-
89
I Crankshaft rear seal carrier retaining bolts I 10 I - I 89 I
Oil drain plug
Oil cooler to oil filter adaptor retaining bolt
I Flywheel retaining bolts I a) I - I - I
28
34
I Knock sensor retaining bolt I 20 I 15 I - I
Oil filter adaptor retaining bolts
Positive crankcase ventilation housing retaining
bolts
I Thermostat housing retaining bolts I 10 I - I 89 I
21
25
I Oil pump retaining bolts I a) I - I - I
-
-
25
10
I Oil pump sprocket retaining bolt I 25 I 18 I - I
18
-
-
89
Oil pump chain guide retaining bolts
Oil pump chain tensioner retaining bolt
I Crankshaft position sensor retaining bolts I 7 I - I 62 I
Timing chain guide retaining bolts
Timing chain tensioner retaining bolts
I Accessory drive belt idler pulley retaining bolt I 25 I 18 I - I
10
10
I Intake manifold retaining bolts I 18 I 13 I - I
10
10
I Transaxle left-hand retaining bolts I 44 I 32 I - I
-
-
I Transaxle right-hand retaining bolts I 44 I 32 I - I
89
89
-
-
89
89
Transaxle lower retaining bolts
Halfshaft center bearing carrier retaining bolts
I Lower arm ball joint retaining bolt I 48 I 35 I - I
Intermediate shaft bearing cap retaining nuts
2006.0 Fiesta 1212006 G451278en
40
48
25 30
35 -
-
18 -
procarmanuals.com

303-01 B-60 Engine - 2.OL Duratec-HE (M14) 303-01 B-60
IN-VEHICLE REPAIR
Engine Front Cover(21 148 0)
f'
General Equipment 6. Detach the coolant expansion tank and lay
I Vehicle jack it to one side.
Materials Name Specification
I Silicone Sealant I WSE-M4G323-A4 I
Removal
1. Remove the crankshaft belt pulley.
For additional information, refer to:
Crankshaft Pulley (303-01 Engine
- 2.OL
Duratec-HE (M14), Invehicle Repair).
2. Remove the timing cover lower bolts.
7. Support the engine with
a vehicle jack.
8. Remove the front engine mount.
Discard the front engine mount nuts.
3. Disconnect the crankshaft position (CKP)
sensor electrical connector.
4. Lower the vehicle.
5. Remove the power steering pump.
For additional information, refer to: Power
Steering Pump
- 2.OL Duratec-HE (M14)
(211 -02 Power Steering, Removal and
Installation).
9. Remove the coolant pump pulley.
2006.0 Fiesta 121~0o6 G451289en
procarmanuals.com

303-01 B-61 Engine - 2.OL Duratec-HE (M14) 303-01 B-61
IN-VEHICLE REPAIR
10. Remove the drive belt idler pulley.
11. Remove the timing cover upper bolts.
Remove the timing cover.
Apply sealer to the timing cover (bead
diameter:
3 mm).
3. Install the timing cover (engine shown
installation removed for clarity).
Tighten the bolts in the sequence shown.
1. Clean the sealing surfaces of the timing Tighten bolts I to 8 to a torque of 10 Nm.
cover and the cylinder block. Tighten bolt 9 to 48 Nm.
2. N0TE:lnstall the timing cover within 10 Tighten bolts 10 to 19 to a torque of 10 Nm.
minutes of applying the silicon sealer.
2006.0 Fiesta 12/2006 G451289en
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)llI25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
SPECIFICATIONS
Lubricants, Fluids, Sealers and Adhesives
Description
Specificatio 1 (,
I
Motorcraft Super Plus 2000 antifreeze
Antifreeze -All vehicles used in climates where daytime ambient air temperature does not regularly
exceed
+46OC (+I 1 5°F)
Specific gravity
(providing no other
additive is in the
coolant) Solidifies
at
Approximate
percentage of anti-
freeze (by volume) Remains
fluid to
Antifreeze
- Vehicles with 1.25U1.4U1 .6L engine used in climates where daytime ambient air
temperature regularly exceeds
+46OC (+I 15OF)
Cooling system, including heater system and coolant expansion tank (all except vehicles
with diesel engine)
1
Specific gravity (providing no other additive is
in the coolant)
Cooling System Refill Capacities Approximate percentage
of antifreeze (by
volume)
Description
I Radiator pressure test I 138 (20) I
Liters
Cooling System Pressure Specification
I Coolant expansion tank cap release pressure I 120 to 150 (17-21) I
Description Pressure kpa (psi)
I Radiator retaining
nut I 10 I - I 89 1
Torque Specifications - vehicles with 1.25U1.4U1 .6L engine
wrpump pulley retaining bolts I 24 I 18 I - I
Ib-in
Description
Thermostat housing retaining bolts
Water pump retaining bolts
I Generator retaining bolts I 45 I 33 I - I
I Generator electrical connector retaining nut I 8 I - I 71 I
Nm
10
10
I Timing belt lower cover retaining bolts I 9 I - I 80 I
I b-ft
Torque Specifications
- vehicles with I .3L engine 1
-
-
I Description I Nm I Ib-ft I Ib-in I,,.
89
89
I Radiator retaining nut I 10 I - I 89 1 '\..
I Water pump pulley retaining bolts I 12 I 9 I - I
Water pump retaining bolts
2006.0 Fiesta 1212006 Gl46257en
10 - 89
procarmanuals.com

Engine Cooling - I .3L DuratecdV
(Rocam)ll.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
DESCRIPTION AND OPERATION
Components
Coolant pump
The coolant pump is secured to the engine block
at the timing gear end.
Item Description It is driven through a pulley b; the accessory drive
2006.0 Fiesta 1212006 GI 79022en
belt.
The gasket for the coolant pump must not be
reused. 1
2
I
Coolant pump
Coolant pump gasket
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-1 6V (Sigma)llI4L
303-03A-22 Duratec-1 6V (Sigma)lIl6L Duratec-1 6V (Sigma) 303-03A-22
REMOVAL AND INSTALLATION
9. Remove the generator.
For
additional information, refer to:
Generator
- 1.25L Duratec-1 6V (Sigma)/l.4L
Duratec-I 6V (Sigma)/l .6L Duratec-I 6V
(Sigma)
(414-02 Generator and Regulator,
Removal and Installation).
10. Remove the water pump pulley.
Discard the gasket.
Vehicles built 0412005 onwards
13. Remove the timing belt.
For additional information, refer to: Timing
Belt (303-01 Engine - 1.25L Duratec-1 6V
(Sigma)ll.4L Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma), ln-vehicle Repair).
11. Remove the timing belt cover (cover shown 14. Drain the cooling system,
removed for clarity). For additional information, refer to: Cooling
12' &AUTION:P~~~~~~ the timing belt and
lower cover from contamination by the
coolant.
Remove the water pump. System
Draining,
Filling and Bleeding -
1.3L Duratec-8V (Rocam)ll.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V (,
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-03
Engine
Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-I 6V (Sigma)/l.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma), General Procedures).
15. Remove the water pump and the timing
belt
tensioner.
Discard the gasket.
2006.0 Fiesta 1212006 GI 89080en
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-1 6V (Sigma)ll.4L
303-03A-23 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-0349-23
REMOVAL AND INSTALLATION
16. Remove the timing belt tensioner from the
water pump.
Installation
1. N0TE:lnstall a new water pump gasket.
To install, reverse the removal procedure.
2006.0 Fiesta 1212006 GI 89080en
procarmanuals.com

303-1 4-2 Electronic Engine Controls 303-1 4-2
SPECIFICATIONS
I Powertrain control module (PCM) retaining bolts I 3 I - I 27 I
Torque Specifications - vehicles with 1.3L Duratec-8V (Rocam) engine
I Knock sensor (KS) retaining bolt I 20 I 15 I - I
Description
I Crankshaft position (CKP) sensor retaining bolt I 10 I - I 89 I
I Camshaft position (CMP) sensor retaining bolt I
I Throttle position (TP) sensor screws I 5 I - I 44 I
Ib-in I/ Nm
I Idle air control (IAC) valve retaining bolts I 10 I - I 89 I
I b-ft
Ignition coil pack retaining bolts
Exhaust manifold heatshield retaining
bolts
Torque Specifications - vehicles with 1.25L Duratec-1 6V (Sigma)ll.4L Duratec-1 6V (Sigma)ll .6L
Duratec-I 6V (Sigma) engine
Heated oxygen sensor (H02S)
Catalyst monitor sensor (CMS)
I Powertrain control module (PCM) retaining bolts I 3 I - I 27 I
6
10
I Knock sensor (KS) retaining bolt I 20 I 15 I - I
47
47
-
-
I Camshaft position (CMP) sensor retaining bolt I 10 I - I 89 I
53
89
35
35
Cylinder head temperature (CHT) sensor
Crankshaft position (CKP) sensor retaining bolt
I Engine coolant temperature (ECT) sensor I 20 I 15 I - I
-
-
I Idle air control (IAC) valve I 10 I - I 89 I
25
10
I Heated oxygen sensor (H02S) I 47 I 35 I - I -- --
I Catalyst monitor sensor (CMS) 47 I 35 1 - I
18
-
-
89
Powertrain control module (PCM) retaining nuts
and retaining bolts
Torque Specifications - vehicles with 1.4L Duratorq-TDCi (DV) Diesel engine
1 Timing belt upper cover retaining bolts I 4 I - I 35 I
I Timing belt lower cover retaining bolts I 6 I - I 53 I
l b-in
Description
I Camshaft position (CMP) sensor retaining bolt I 5 I - I 44 I
I Crankshaft position (CKP) sensor retaining bolt I 8 I - I 71 I
Nm
I Crankshaft pulley retaining bolt I a I - I - I
I b-ft
I- .
For additional information, refer to: Crankshaft Position (CKP) Sensor - 1.4L Duratorq-Ci D) Diesel (303-14 Electronic Engine ''
I Controls, Removal and Installation).
2006.0 Fiesta 1212006 Gl48226en
procarmanuals.com