2007 FORD FIESTA 303-01

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-52
Duratec-1 6V (Sigma)ll.GL Duratec-1 6V (Sigma)
303-0 1 A-52
IN-VEHICLE REPAIR
13. Connect the catalyst monitor sensor
17. Install the exhaust manifold lower heat
electrical connector.
shield left-hand retaining bolts.
I I 'b -
14. Connect the heated oxygen (HO2S) sensor
18. Install the engine support insulator
electrical connector. retaining bolt.
15. Raise and support the vehicle. 19. Attach the exhaust system insulators to the
For additional information, refer to: Lifting exhaust
brackets.
(1 00-02 Jacking and Lifting, Description
20. N0TE:lnstall a new exhaust manifold gasket
and Operation). and new nuts.
16. Position the exhaust manifold lower heat
Attach the exhaust flexible pipe to the
shield and install the right-hand retaining
catalytic converter.
bolt.
21. Remove the exhaust flexible pipe support
wrap or splint.
2006.0 Fiesta 1212006 GI 83739en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-53 Duratec-1 6V (Sigma)/l .6L
Duratec-1 6V (Sigma) 303-01 A-53
IN-VEHICLE REPAIR
22. Lower the vehicle.
23. Install the air cleaner.
' For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)llm4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (303-1 2 Intake Air Distribution
and
Filtering, Removal and Installation).
24. Connect the battery ground cable.
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
2006.0 Fiesta 1212006 GI 83739en
procarmanuals.com

Engine - I .25L Duratec-1 6V (Sigma)llI4L
303-01 A-54 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-54
IN-VEHICLE REPAIR
Cylinder Head(21 163 0)
1 I Socket, Cylinder Head Bolts I
Discard the gasket and the nuts. (
Removerllnstaller, Hose
Clamp
303-397 (24-003)
I 24003 1 1 5. Raise and support the vehicle.
Removal
I I 1 For additional information, refer to: Lifting
(100-02 Jacking and Lifting, Description
1. Release the fuel system pressure.
Materials
For
additional information, refer to: Fuel
System Pressure Release (31 0-00 Fuel
System - General Information, General
Procedures). and
Operation).
2. Drain the
cooling system.
For
additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 1.4L
Duratorq-TDCi (DV) Diesel, General 7. Remove the exhaust manifold lower heat
Procedures). shield left-hand retaining bolts.
3. Remove the camshaft.
Name
Specification
6. Using a suitable splint or wrap support the
For
additional information, refer to:
Camshafts
(303-01 Engine - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma),
In-vehicle Repair).
Engine oil I WSS-M2C912-A1
4. Detach the exhaust flexible pipe from the
catalytic converter. exhaust
flexible pipe.
8. Remove the exhaust manifold lower heat
shield right-hand retaining bolts.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
303-01 Am55 Duratec-1 6V (Sigma)lll6L Duratec-1 6V (Sigma) 303-01 A-55
IN-VEHICLE REPAIR
Remove the lower heat shield.
9.
Remove the intake manifold retaining bolt.
10. Lower the vehicle.
12. Disconnect the brake booster vacuum line
from the intake manifold.
13. Disconnect the positive crankcase
ventilation (PCV) hose from the PCV.
11. Disconnect the vacuum hose from the fuel
pressure regulator.
14. Disconnect the generator electrical
connector.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-56 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-56
IN-VEHICLE REPAIR
15. Disconnect the evaporative emissions 18. Disconnect the fuel supply line quick
(EVAP) hose from the EVAP valve.
release coupling.
f
16. Disconnect the engine wiring harness
electrical connector.
17. Disconnect the EVAP valve electrical
connector. For
additional information, refer to: Quick
(..
Release Coupling (310-00 Fuel System -
General Information, General Procedures).
I 9. Disconnect the fuel return line quick release
coupling.
For additional information, refer to: Quick
Release Coupling
(31 0-00 Fuel System -
General Information, General Procedures).
20. Using the special tool, disconnect the
coolant hose from the coolant distribution
assembly.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
303-01 A-59 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-59
IN-VEHICLE REPAIR
installation 2. Attach the oil level indicator tube to the
intake manifold.
! ACAUTION:T~~ thickness of the new
cylinder head gasket must be the same as
that of the old one (hole marked).
N0TE:lnstall a new cylinder head gasket.
N0TE:Position the cylinder head into the two guide
sleeves.
Using the special tool, install the cylinder
head.
Tighten the cylinder head bolts in the
sequence shown in three stages.
Stagel: 15Nm.
Stage 2: 30 Nm.
Stage 3: 90 degrees. 3. Install the timing belt rear cover (engine
shown removed for clarity).
4. N0TE:lnstall a new exhaust manifold gasket
and new exhaust manifold retaining nuts.
N0TE:Do not fully tighten the nuts and bolt at this
stage.
Install the exhaust manifold.
5. Tighten the exhaust manifold upper retaining
nuts and bolt in the sequence shown in two
stages.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01A-61 Duratec-1 6V (Sigma)/l .6L Duratec-I 6V (Sigma) 303-OIA-61
IN-VEHICLE REPAIR
11. Connect the engine coolant temperature 14.
Using the special tool, connect the coolant
/ (ECT) sensor electrical connector.
hose to the coolant distribution assembly.
12. Using the special tool, connect the degas 15.
Connect the fuel return line quick release
hose to the cylinder head. coupling.
13. Using the special tool, connect the coolant
hose to the coolant distribution assembly. For additional
information, refer to: Quick
Release Coupling (310-00 Fuel System
-
General Information, General Procedures).
16. Connect the fuel supply line quick release
coupling.
For additional information, refer to: Quick
Release Coupling (310-00 Fuel System
-
General Information, General Procedures).
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-63 Duratec-1 6V (Sigma)/l.6L Duratec-1 6V (Sigma) 303-01 A-63
IN-VEHICLE REPAIR
23. Connect the brake booster vacuum line to 27. Install the
exhaust manifold lower heat
the intake manifold. shield
left-hand retaining bolts.
24. Raise and support the vehicle. 28.
N0TE:lnstall a
new flexible pipe gasket and
For
additional information, refer to: Lifting new
nuts.
(1 00-02 Jacking and Lifting, Description Attach the flexible pipe to the catalytic
and Operation). converter
25.
Install the intake manifold retaining bolt.
29. Remove the exhaust flexible pipe support.
26. Position the exhaust
manifold lower heat . 30, Install the camshaft.
shield and install the right-hand retaining
For additional information, refer to:
bolts. Camshafts (303-01 Engine
- 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma),
In-vehicle Repair).
31.
N0TE:lnstall a new oil filter.
Change the engine oil.
32. Fill and bleed the cooling system.
For
additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 1.4L
Duratorq-TDCi (DV) Diesel, General
Procedures).
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com