2007 FORD FIESTA transmission cover

308-02-6 Clutch Controls 308-02-6
REMOVAL AND INSTALLATION
Clutch Slave Cylinder(l6 862 4) /'
Materials Alf brake fluid is spilt on the paintwork, the
Name Specification affected
area must be
immediately washed
ESDM-1 C220-A down with cold water. High-temperature
grease
ADO not apply grease on any area of the
clutch slave cylinder.
Removal Install the clutch slave cylinder.
I. Remove the transaxle. For additional
information, refer to: (308-03 Manual
TransmissionlTransaxle)
Transaxle - 1.2 5L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (Removal),
Transaxle - 1.3L Duratec-8V (Rocam)
(Re m ova I),
Transaxle - 2.OL Duratec-HE (M14) (Removal),
Transaxle - 1.4L Duratorq-TDCi (DV)
Dieselll.6L Duratorq-TDCi (DV) Diesel
(Removal).
2. Clean any grease and foreign material from
the input shaft.
3. CAUTIONS:
Alf brake fluid is spilt on the paintwork, the
affected area must be
immediately washed
down with
cold water.
Ausing suitable adhesive tape, cover the
input shaft
splines to prevent damage to the
input shaft
oil seal.
Remove the clutch slave cylinder.
Installation
1. CAUTIONS: 2.
Remove the adhesive tape from the input
shaft
splines.
3. Coat the input shaft splines with a thin layer
of high-temperature grease.
4.
Install the transaxle. For additional
information, refer to: (308-03 Manual
TransmissionlTransaxle)
Transaxle - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (Installation),
Transaxle - 1.3L Duratec-8V (Rocam)
(Installation),
Transaxle - 2.OL Duratec-HE (M14)
(Installation),
Transaxle - 1.4L Duratorq-TDCi (DV)
Dieselll.6L Duratorq-TDCi (DV) Diesel
(Installation).
2006.0 Fiesta 1212006 GI1 3288en
procarmanuals.com

308-0314 Manual Transmission/Transaxle 308-03-4 -- --
SPECIFICATIONS
2006.0 Fiesta 1212006 GII 3289en
Item
Transaxle housing final drive cover retaining bolts
Transaxle to engine retaining bolts
Engine support insulator to engine retaining bolt
Engine support insulator to
subframe retaining bolts
Engine rear mount outer retaining nuts
Exhaust flexible pipe retaining nuts
Wiring harness retaining bracket retaining nut Power steering high-pressure line retaining bracket
retaining bolt
Lower arm ball joint to the wheel knuckle retaining
nut
Engine rear mount center retaining nut
Intermediate shaft center bearing retaining nuts
Strut and spring assembly top mount retaining nuts
Transmission fluid filler plug
Starter motor retaining bolts
Starter motor wiring harness retaining bracket retaining nuts Nm
12
47
48
48
48
44
22
25
52
90
25
48 35
35
20
Ib-ft
9
35
35
35
35
32
16
21
38
66
18
35
26
26
15
I b-in
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
procarmanuals.com

308-03-24 Manual Transmission/Transaxle 308-03-24
REMOVAL
5. Install the special tools. 9. Disconnect the reversing lamp switch
electrical connector.
//
I I
6. Remove the transaxle upper retaining bolts.
Detach the engine wiring harness bracket Vehicles with automated gearshift
from the transaxle. 10. Remove the gearshift actuator cover.
7. Remove the front wheels and tires. 11. Disconnect the gearshift actuator electrical
For additional information, refer to: Wheel connector (colored
black).
and Tire
(204-04 Wheels and Tires, Removal
and Installation).
8. Remove the starter motor.
Detach the starter motor electrical connector
from the starter motor.
2006.0 Fiesta 1212006 - Gl13290en
procarmanuals.com

308-03125 Manual Transmission/Transaxle 308-03-25
REMOVAL
12. Disconnect the gearshift actuator electrical 1. Detach the gearshift cables and the selector
connector (colored grey). cable from the selector levers.
2. Turn the abutment sleeve clockwise and
detach the cables from the bracket.
13. ACAUTION:~~ brake fluid is spilt on the
paintwork, the affected area must be
All vehicles immediately washed down with cold water. 16. Remove the accessory drive belt cover.
Disconnect the clutch slave cylinder supply
line.
Remove the spring clip.
Vehicles without automated gearshift
14. Remove the gearshift cables cover.
I*' A~AuT10N:~rotect the ball joint seal
using a soft cloth to prevent damage.
Detach the lower arm from the wheel knuckle
15. Detach the gearshift cables from the on both
sides.
transaxle.
2006.0 Fiesta 1212006 GI 13290en
procarmanuals.com

308-03-31 Manual TransmissionlTransaxle 308-03-31
REMOVAL
5. Remove the transaxle upper retaining bolts. Detach the wiring harness from the retaining
bracket.
6. Detach the power steering high-pressure line
retaining bracket from the transaxle. 10.
Disconnect the reversing lamp switch
electrical connector.
7. Remove the front wheels and tires.
11. Remove the gearshift cables cover.
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
I
and Installation).
8. Remove the wiring harness retaining bracket.
9. Remove the starter motor. 12.
Detach the gearshift cables from the
transaxle.
1. Detach the gearshift cables and the selector
cable from the selector levers.
- -
2006.0 Fiesta 1212006 G453416en
procarmanuals.com

308-03-32 Manual Transmission/'rransaxle 308-03-32
REMOVAL
2. Turn the abutment sleeve clockwise and
detach the cables from the bracket. 17' ACAUTION:~~~~ bending of the exhaust
flexible pipe may cause damage resulting
/
in failure. \.
Support the exhaust flexible pipe with a
suitable support wrap or suitable splint.
13. Remove the accessory drive belt cover.
14. Remove the engine support insulator.
15. Remove the left-hand halfshaft.
For additional information, refer to: Front
Halfshaft LH
(205-04 Front Drive
Halfshafts, Removal and Installation).
16. Remove the right-hand halfshaft.
For additional information, refer to: Front
Halfshaft RH
(205-04 Front Drive
Halfshafts, Removal and Installation).
18. Lower the vehicle.
Igm ACAUTION:~~ brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
Disconnect the clutch slave cylinder supply
line.
Remove the spring clip.
20.
Detach the exhaust flexible pipe from the
catalytic converter.
2006.0 Fiesta 1212006 G453416en
procarmanuals.com

308-03-36 Manual Transmission/Transaxle 308-03-36
DISASSEMBLY
3. Remove the clutch slave cylinder. 2. Remove and discard the snap ring.
J'
4. Remove the vehicle speed sensor (VSS) (if 7m Remove the gearshift cable
equipped).
1. Remove the retaining pin.
2. Pull out the VSS.
5. Remove the selector mechanism cover.
6. Remove the gearshift lever.
1 . Remove the protective cap (if equipped).
8. Remove the selector lever.
Remove the bellows.
2006.0 Fiesta 1212006 G23118en
procarmanuals.com

308-03-37 Manual Transmission/Transaxle 308-03-37
DISASSEMBLY
9. Remove the selector interlock mechanism. 2. Remove and discard the retaining pin.
10. Remove the fifth gear housing cover 13. N0TE:To aid assembly mark the position
retaining bolts. of
the fifth gear synchroniser assembly.
11. Using the special tool, remove the fifth gear
housing cover.
12. Remove the fifth gear synchroniser
assembly, the selector fork and the fifth
gear.
I. Remove and discard the snap ring. I
Disassemble the fifth gear and synchroniser
assembly.
1. Snap ring.
2. Retaining plate.
3. Synchroniser assembly.
4. Synchroniser ring.
5. Fifth gear.
14. Remove the fifth gear snap ring.
2006.0 Fiesta 1212006 G23118en
procarmanuals.com