2007 FORD FIESTA radiator

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 24 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-1 24
INSTALLATION
Attach the right-hand halfshaft and the Install the heat shield.
intermediate shaft to the transaxle.
13. CAUTIONS:
Asupport the halfshaft. The inner joint
must not be bent more than
18 degrees.
The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft oil seal.
A~ake sure the snap ring is correctly
seated.
N0TE:lnstall a new snap ring.
Attach the left-hand halfshaft to the
transaxle.
14. Attach the lower arm to the wheel knuckle
on both sides (right-hand side shown).
15. Using the special tool, connect the coolant
hose to the distribution pipe
16. Using the special tool, connect the coolant
hose to the radiator.
2006.0 Fiesta 1212006 Gll3164en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-1 37
INSTALLATION
Install the heat shield. 2. Install the cooling fan motor and shroud to
the retaining brackets.
16. Using the special tool, connect the coolant
hose to the distribution pipe.
19. Connect the cooling fan motor and cooling
fan resistor electrical connectors.
17. Using the special tool, connect the coolant
hose to the radiator.
20. Using the special tool, attach the power
steering line to the power steering pump.
18. Install the cooling fan motor and shroud.
1. Push the cooling fan motor and shroud
upwards and then downwards to install.
2006.0 Fiesta 1212006 G380459en
procarmanuals.com

303-01 B-23 Engine - 2.OL Duratec-HE (M14) 303-01 B-23
IN-VEHICLE REPAIR
17. Disconnect the intake manifold runner 20. Disconnect the hood latch electrical
control (IMRC) electrical connector. connector.
18. Disconnect the throttle body electrical 21. Remove the hood latch lever retaining bolt.
connector.
22. Detach the hood latch from the radiator
19. Disconnect the knock sensor (KS) electrical grille
opening panel reinforcement.
connector (power steering fluid reservoir
shown removed for clarity).
Detach the KS electrical connector from the
intake manifold.
2006.0 Fiesta 1212006 G451284en
procarmanuals.com

Engine Cooling - I .3L Duratec-8V
(Rocam)llI25L Duratec-1 6V (Sigma)llm4L
303-03A-1 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-03A-I
i
SECTION 303-03A Engine Cooling - 1.3L Duratec-8V
(Rocam)/l.25L Duratec-1 6V (Sigma)/l.4L Duratec-1 6V
(Sigma)/l .6L Duratec-1 6V (Sigma)
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS PAGE
SPECIFICATIONS
Specifications ........................................................................\
....................................... 303-03A-2
DESCRIPTION AND OPERATION
Engine Cooling - 1.4L Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) ......................... 303-03A-4
Overview..
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303-03A-4
Components..
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303-03A-5
DIAGNOSIS AND TESTING
Engine Cooling ........................................................................\
........................................... 303-03A-8
Inspection and Verification
........................................................................\
...................... 303-03A-8
j Symptom Chart ........................................................................\
........................................... 303-03A-8
Component Tests..
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303-03A-4 6
GENERAL PROCEDURES
Cooling System Draining, Filling and Bleeding - I .3L Duratec-8V
(Rocam)/l.25L Duratec-1 6V (Sigma)/l.4L Duratec-1 6V (Sigma)/l.GL
Duratec-1 6V (Sigma). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (24 122 0) 303-03A-19
Draining
........................................................................\
...................................................... 303-03A-19
Filling and Bleeding
........................................................................\
.............................. 303-03A-19
REMOVAL AND INSTALLATION
Water Pump - 1.25L Duratec-I 6V (Sigma)/l.4L Duratec-I 6V (Sigma)ll .6L
Duratec-1 6V (Sigma). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (24 404 0) 303-03A-21
Thermostat
- 1.25L Duratec-1 6V (Sigma)/l.4L Duratec-1 6V (Sigma)/l .6L
Duratec-1
6V (Sigma) ........................................................................\
........... . (24 454 0) 303-03A-24
Radiator
........................................................................\
.................................. (24 254 0) 303-03A-26
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)llI25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
SPECIFICATIONS
Lubricants, Fluids, Sealers and Adhesives
Description
Specificatio 1 (,
I
Motorcraft Super Plus 2000 antifreeze
Antifreeze -All vehicles used in climates where daytime ambient air temperature does not regularly
exceed
+46OC (+I 1 5°F)
Specific gravity
(providing no other
additive is in the
coolant) Solidifies
at
Approximate
percentage of anti-
freeze (by volume) Remains
fluid to
Antifreeze
- Vehicles with 1.25U1.4U1 .6L engine used in climates where daytime ambient air
temperature regularly exceeds
+46OC (+I 15OF)
Cooling system, including heater system and coolant expansion tank (all except vehicles
with diesel engine)
1
Specific gravity (providing no other additive is
in the coolant)
Cooling System Refill Capacities Approximate percentage
of antifreeze (by
volume)
Description
I Radiator pressure test I 138 (20) I
Liters
Cooling System Pressure Specification
I Coolant expansion tank cap release pressure I 120 to 150 (17-21) I
Description Pressure kpa (psi)
I Radiator retaining
nut I 10 I - I 89 1
Torque Specifications - vehicles with 1.25U1.4U1 .6L engine
wrpump pulley retaining bolts I 24 I 18 I - I
Ib-in
Description
Thermostat housing retaining bolts
Water pump retaining bolts
I Generator retaining bolts I 45 I 33 I - I
I Generator electrical connector retaining nut I 8 I - I 71 I
Nm
10
10
I Timing belt lower cover retaining bolts I 9 I - I 80 I
I b-ft
Torque Specifications
- vehicles with I .3L engine 1
-
-
I Description I Nm I Ib-ft I Ib-in I,,.
89
89
I Radiator retaining nut I 10 I - I 89 1 '\..
I Water pump pulley retaining bolts I 12 I 9 I - I
Water pump retaining bolts
2006.0 Fiesta 1212006 Gl46257en
10 - 89
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
DESCRIPTION AND OPERATION
Engine Cooling - 1.4L Duratec-I 6V (Sigma)/l .6L Duratec-1 6V
(Sigma)
Overview
2006.0 Fiesta 1212006 GI 79022en
Description Item Description
I "
(
4
5
6
7
Heater heat exchanger
Thermostat housing
Coolant expansion tank Radiator
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-1 6V (Sigma)ll.4L
303-03A-8 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-03A-8
DIAGNOSIS AND TESTING
Engine Cooling
Special Tool(~)
Pressure Tester,
Cooling
System
303-396 (24-001 A)
General
Equipment
I Worldwide Diagnostic System (WDS) I
Visual Inspection Chart i,
I Mechanical I Electrical I
- Coolant leak(s)
- Coolant level
- Air in system
- Gasketslseals
- Hose(s)lhose joints
- Coolant expansion
tank cap and
seal
- Coolant expansion
tank
- Radiator
- Water pump
- Thermostat
- Thermostat housing
- Accessory drive belt
- Fuse(s)
- Relay(s)
- Wiring harness
- Electrical
connector(s)
- Cooling fan motor
- Engine coolant
temperature (ECT)
sensor
- Cylinder head
temperature (CHT) sensor
- Powertrain control
module (PCM)
3.
If an obvious cause for an observed or reported Inspection and Verification concern is found, correct the cause (if possible)
before proceeding to the next step.
1. Verify the customer concern.
4.
If the cause is not visually evident, verify the ( 2. Visually inspect for obvious signs of mechanical
symptom and refer to the Symptom Chart.
or
electrical damage.
Symptom Chart
Symptom Chart
Svm
ptom Possible Sources Action
Loss of
coolant INSPECT the hoses and hose
joints. INSTALL a new
hose(s)
as necessary.
Radiator. INSPECT the radiator for leaks.
CARRY OUT the Pressure Test
Component Test in this section.
INSTALL a new radiator as
necessary.
REFER to: Radiator (303-03 Engine
Cooling - 1.3L
Duratec-8V (Rocam)/l.25L
Duratec-1 6V (Sigma)1ln4L
Duratec-1 6V (Sigma)ll .6L
Duratec-I 6V (Sigma),
Removal and Installation).
2006.0 Fiesta 1212006 GI 46258en
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)llI25L Duratec-1 6V (Sigma)llI4L
303-03A-I I Duratec-1 6V (Sigma)/lI6L Duratec-I 6V (Sigma) 303-03A-1 I
DIAGNOSIS AND TESTING
Symptom
The engine overheats (signs of
coolant boiling)
Possible Sources Action
Cooling system does not hold
pressure.
Radiator. CARRY
OUT the Coolant
Expansion Tank Cap Test
Component Test in this section.
INSPECT the coolant expan-
sion tank for damage. INSTALL
a new coolant expansion tank
as necessary.
INSPECT the water pump or
water pump gasket for damage.
INSTALL a new water pump or
water pump gasket as neces-
sary.
REFER to: Water Pump
- 1.3L
Duratec-8V (Rocam) (303-03
Engine Cooling
- 1.3L
Duratec-8V (Rocam)/l.25L
Duratec-I 6V (Sigma)/l.4L
Duratec-1 6V (Sigma)/l .6L
Duratec-I 6V (Sigma),
Removal and Installation)
/ Water Pump - 1.25L Duratec-
16V
(Sigma)ll.4L Duratec-
16V
(Sigma)/l .6L Duratec-
16V (Sigma) (303-03 Engine
Cooling
- 1.3L Duratec-8V
(Rocam)/l.25L Duratec-1 6V
(Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V
(Sigma), Removal and
Installation).
INSPECT the engine, cylinder
head, cylinder block and
cylinder head gasket.
REFER to: Cylinder Head (303-
01 Engine
- 1.25L Duratec-
16V
(Sigma)/l.4L Duratec-
1 6V
(Sigma)/l .6L Duratec-
16V (Sigma), In-vehicle
Repair).
INSPECT the radiator for
blockage or damage. CARRY
OUT the Pressure Test
Component Test in this section.
INSTALL a new radiator as
necessary.
REFER to: Radiator (303-03
Engine Cooling
- 1.3L
Duratec-8V (Rocam)ll.25L
Duratec-I 6V (Sigma)/l.4L
Duratec-1 6V (Sigma)/l .6L
Duratec-I 6V (Sigma),
Removal and Installation).
2006.0 Fiesta 1212006 GI 46258en
procarmanuals.com