2007 FORD FIESTA gasket

308-03-33 Manual Transmission/Transaxle 308-03-33
REMOVAL
Discard the gasket.
,
23. Using the special tools, lower the engine
and transaxle assembly.
21. Remove the battery tray support bracket.
24. Remove the engine and transaxle rear
mount retaining bracket.
22. Remove the engine and transaxle rear
mount.
Discard the nuts. 25. Raise and support the vehicle. For
additional information, refer to:
(1 00-02
Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
26. Remove the transaxle lower retaining bolts.
27. N0TE:Secure the transaxle with a retaining
strap on the transmission jack.
2006.0 Fiesta 1212006 G453416en
procarmanuals.com

308-03-38 Manual Transmission/Transaxle 308-03-38
DISASSEMBLY
Discard the snap ring. 4. Pull out the blanking plug.
15. Using the special tool, remove the fifth
18. Using the special tool, remove both
gear. halfshaft oil seals (left-hand side shown).
16. Remove the fifth gear housing.
Discard the bolts.'
17. Remove the fifth gear housing gasket, the
snap rings and the blanking plug.
1. Remove and discard the gasket.
2. Remove the output shaft snap ring.
3. Remove the input shaft snap ring.
Only remove the reversing lamp switch if
there is evidence of leakage.
19. Separate the two halves of the transaxle
housing (14 bolts).
Carefully separate the transaxle housing.
20. Remove the selector shaft guide sleeve
upper snap ring.
I' j '\.
1. Remove and discard the upper snap ring.
2006.0 Fiesta 1212006 G23118en
procarmanuals.com

308-03-57 Manual Transmission/Transaxle 308-03-57 I I
ASSEMBLY
21. Apply sealer on the inside edge of the Install
the fifth gear housing gasket.
1. transaxle housing mating face.
22. Assemble the transaxle housing and tighten 26m ACAUTION:M~~~ sure the snap rings are
in the correct position. Failure to follow this
the bolts.
instruction may cause damage to the fifth
23. N0TE:lnstall new input and output shaft
snap rings. gear
housing.
Turn the snap rings to the position shown.
Raise the and shafts 'lightly 27. NOTE:lnstall new fifth gear housing
and install the snap rings.
retaining bolts.
' 24. Using a suitable thread die, clean all the Install
the fifth gear housing.
-I hole threads in the fifth gear housing.
25. N0TE:lnstall a new fifth gear housing 28. Remove the transaxle from the mounting
stand.
gasket.
2006.0 Fiesta 1212006 G23119en
procarmanuals.com

308-03-63 Manual Transmission/Transaxle 308-03-63
INSTALLATION
4. Install the transaxle left-hand retaining bolt. Install the
engine rear mount.
5. Remove the retaining strap. 11. Remove the special tools.
6. Remove the transmission jack.
7. Install the engine and transaxle rear mount
retaining bracket.
12. N0TE:lnstall new exhaust flange nuts and
a new exhaust flange gasket.
Attach the exhaust flexible pipe to the
8. Lower the vehicle. catalytic
converter.
9. Using the special tools, raise the engine and
transaxle assembly.
10. N0TE:Do not tighten the engine rear mount
retaining nuts at this stage.
NOTE:
Install new engine rear mount retaining nuts.
2006.0 Fiesta 1212006 GI1 3293en
procarmanuals.com

308-03-70 Manual Transmission/Transaxle 308-03-70
INSTALLATION
3. Install the transaxle lower retaining bolts. 9. Using the special tools, raise the engine and
transaxle assembly.
f
4. Install the transaxle left-hand retaining bolt.
10. N0TE:Do not tighten the engine rear mount
retaining nuts at this stage.
N0TE:lnstall new engine rear mount retaining nuts.
Install the engine rear mount.
5. Remove the retaining strap.
6. Remove the transmission jack.
7. Lower the vehicle.
8. Install the engine and transaxle rear mount
retaining bracket. 11. Remove the special tools.
12. N0TE:lnstall new exhaust flange nuts and ,
a new exhaust flange gasket.
2006.0 Fiesta 1212006 G453417en
procarmanuals.com

309-00-7 Exhaust System 309-00-7
REMOVAL AND INSTALLATION
1 6 1 Catalytic converter. Description
Item Description
Removal Details
assembly
retaining clamp
Item 3 Exhaust hanger insulator ltem 6 catalvtic converter.
See
Removal Detail
See Installation Detail II CAUTI0N:Take care when removing the
exhaust hanger insulator to prevent A CAUTI0N:Using cable ties, support the
damage. muffler
and tailpipe assembly to prevent
damage to the exhaust hanger insulators.
See Removal
Detail
See Installation Detail
4. To install, reverse the removal procedure.
Item 5 Catalytic converter to muffler and tailpipe N0TE:Discard the catalytic converter to exhaust
assembly retaining clamp flexible pipe gasket.
N0TE:Discard the
catalytic converter to muffler
and tailpipe assembly clamp retaining nut.
Installation Details
, ltem 6 Catalytic converter.
' N0TE:Remove the cable ties.
N0TE:lnstall a new catalytic converter to exhaust
flexible pipe gasket.
Item 5 Catalytic converter to muffler and tailpipe
assembly retaining clamp
N0TE:lnstall a new catalytic converter to muffler
and tailpipe assembly clamp retaining nut.
Item 3 Exhaust hanger insulator
A CAUTI0N:Take care when installing the
exhaust hanger insulator to prevent
damage.
N0TE:Check the exhaust hanger insulator for
damage. Install a new exhaust hanger insulator if
required.
2006.0 Fiesta 1212006 G453448en
procarmanuals.com

31 0-01 -1 6 Fuel Tank and Lines 31 0-01 -1 6
REMOVAL AND INSTALLATION
Connect the fuel level resistor card electrical
connectors.
3. Make sure that the float rod and arm are able
to sweep their full ranges without contacting
or fouling on any wires.
Vehicles with diesel engine
4. N0TE:lnstall a new fuel level sensor gasket.
Install the fuel level sensor.
For additional information, refer to: Fuel Tank
(310-01 Fuel Tank and Lines, Removal and
InStallation).
All except vehicles with diesel engine
5. N0TE:lnstall a new fuel pump and sender
unit gasket.
Install the fuel pump and sender unit.
For additional information, refer to: Fuel Tank
(310-01 Fuel Tank and Lines, Removal and
Installation).
2006.0 Fiesta i21~006 G913201 en
procarmanuals.com