2007 FORD FIESTA engine coolant

303-03B-17 Engine Cooling - 2.OL Duratec-HE (M14) 303=03B-17 --
GENERAL PROCEDURES
Cooling System Draining, Filling and Bleeding(24 122 0)
Draining
, Special Tool(s) Allow the coolant to drain into a suitable
Im AWARNING:~~~~ releasing the cooling
system pressure, cover the coolant
expansion tank cap with a thick cloth to
prevent the possibility of scalding. Failure
5. Install the radiator lower hose.
to follow this instruction may result in
personal injury.
6. Lower the vehicle.
Release the cooling system pressure by
slowly turning the coolant expansion tank
Filling and Bleeding
cap a quarter of a turn. 1. Fill the coolant expansion tank to the MAX
mark.
container.
24003
2. Remove the coolant expansion tank cap.
3. Raise and support the vehicle.
For additional information, refer to: Lifting
(1 00-02 Jacking and Lifting, Description
and Operation).
4. Using the special tool, disconnect the
radiator lower hose to drain the cooling
system.
Removerllnstaller, Cooling
Hose Clamp
303-397 (24-003)
2. N0TE:Do not allow the engine to reach
normal operating temperature.
Start the engine, run the engine briefly at
2500 revolutions per minute (RPM) for 10
seconds to prime the heater circuit.
3. Switch the engine off.
4. Fill the coolant expansion tank 15 mm over
the MAX mark.
5. Install the coolant expansion tank cap.
6. Start the engine, maintain the engine speed
at
2500 RPM for eight minutes or until the
engine reaches normal operating
temperature.
2006.0 Fiesta 1212006
procarmanuals.com

303-038-1 8 Engine Cooling - 2.OL Duratec-HE (M14) 303-03B-18
GENERAL PROCEDURES
7. Maintain the engine speed at 2500 RPM for
three minutes after the engine has reached
normal operating temperature.
8. lncrease the engine speed to 4000 RPM for
five seconds.
9. Decrease the engine speed to 2500 RPM for
three minutes.
10. lncrease the engine speed to 4000 RPM for
five seconds.
11. Decrease the engine speed to 2500 RPM
for three minutes.
12. Switch the engine off.
13. Check the cooling system for leaks.
14. Allow the engine to cool.
15. Fill the coolant expansion tank to the MAX
mark.
2006.0 Fiesta 1212006 G421226en
procarmanuals.com

303-03B-19 Engine Cooling - 2.OL Duratec-HE (M14) 303-03B-19
REMOVAL AND INSTALLATION
Coolant Pump(24 404 0)
1. Drain the cooling system. 3.
Loosen the coolant pump pulley retaining bolts. - - - - - - -
For additional information, refer to: Cooling -
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 2.OL Duratec-HE
(M14), General Procedures).
2. Remove the crankshaft pulley splash shield.
4. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive Belt
- 2.OL Duratec-HE
(M 14) (303-05 Accessory Drive, Removal
and Installation).
5. Remove the components in the order
indicated in the following
illustration(s) and
table(s).
2006.0 Fiesta 1212006 G421227en
procarmanuals.com

303-03B-20 Engine Cooling - 2.OL Duratec-HE (M14) 303-03B-20
REMOVAL AND INSTALLATION
Item Description
1
2
6. To install, reverse the removal procedure.
Coolant pump pulley
Coolant pump retaining bolts
3
4
2006.0 Fiesta 1u2oos G421227en
- --
Coolant pump
Coolant pump gasket
procarmanuals.com

303-03B-21 Engine Cooling - 2.OL Duratec-HE (M14) 303-03B-21
REMOVAL AND INSTALLATION
Thermostat Housing
Special Tool(s) 2. Lower the vehicle.
I Remover/lnstaller, Coolant 1 3. Remove the right-hand headlamp assembly.
1. Drain the cooling system.
I
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling
- 2.OL Duratec-HE
(M14), General Procedures).
Hose Clamp
303-397 For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
4. Remove the components in the order
indicated in the following
illustration(s) and
table(s).
2006.0 Fiesta 1212006 G426583en
procarmanuals.com

303-03B-22 Engine Cooling - 2.OL Duratec-HE (M14) 303-03B-22
REMOVAL AND INSTALLATION
Item Description Item Description
I 1 coolant hose
Removal Details
2
2006.0 Fiesta 1212006 G426583en
1
3
Thermostat housing to coolant expansion
tank and heater core return coolant hose
See Removal Detail
Radiator lower to thermostat housing See
Removal Detail
Thermostat housing
5. To install, reverse the removal procedure.
procarmanuals.com

303-03B-23 Engine Cooling - 2.OL Duratec-HE (M14) 303-03B-23
REMOVAL AND INSTALLATION
Item 1 Thermostat housing to coolant expansion
tank and heater core return coolant hose
' . I. Using the special tool, disconnect the
thermostat housing to coolant expansion
tank and heater core return coolant hose.
Item 2 Radiator lower to thermostat housing
coolant hose
1. Using the special tool, disconnect the
radiator lower to thermostat housing coolant
hose.
2006.0 Fiesta 1212006 G426583en
procarmanuals.com

303-03B-24 Engine Cooling - 2.OL Duratec-HE (M14) 303-03B-24
REMOVAL AND INSTALLATION
Coolant Outlet Connector
Removal
1. Remove the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
2. Disconnect the spark plug wires from the
ignition coil pack.
4. Remove the ignition coil pack.
5. Drain the cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling
- 2.OL Duratec-HE
(M14), General Procedures).
6. Disconnect the engine coolant temperature
3. Disconnect the ignition coil pack electrical
(ECT) sensor electrical connector.
connector.
2006.0 Fiesta 1212006 G421228en
procarmanuals.com