2007 FIAT ULYSSE lock

IN AN EMERGENCY
156
CHANGING A WHEEL
Please note:
– the jack weighs 3.4 kg;
– the jack requires no adjustments;
– the jack cannot be repaired. If it
breaks it must be replaced with a new
jack;
– no tool with the exception of the
handle can be fitted on the jack.
Proceed as follows:
1) Stop the car in a position that is
not dangerous for oncoming traffic
where you can change the wheel safe-
ly. The ground should be flat and ad-
equately firm. 2) Turn the engine off and pull up the
handbrake.
3) Engage first gear or reverse or, for
versions with automatic electronic
gear, select P.
4) Lift the boot mat (see the relative
instructions in the “Bonnet” paragraph
of “Getting to know your car” chap-
ter).
5) Remove lever A-fig. 3.6) Remove protective cover Band
use ring Cto release the elastic band
D, then extract jack E.
7) Close the bonnet and place the
tools next to the wheel to be changed.
8) Open the tailgate and use ringA-
fig. 4to lift and turn cap Bprotect-
ing the spare wheel lock bolt C.
fig. 3
F0B0118b
fig. 4
F0B0119b

IN AN EMERGENCY
160
GENERAL INSTRUCTIONS
– When a light is not working, check
that it has not fused before changing
the bulb.
– For the location of the fuses, refer
to “If a fuse blows” in this chapter.
– Before replacing a bulb that does
not work, check that the contacts are
not oxidised.
– Burnt-out bulbs must be replaced
with ones of the same type and pow-
er.
– Always check the height of the
headlight beam after changing a bulb.TYPES OF BULBS fig. 12
Several types of bulbs are installed in
the vehicle:
A -Glass bulbs: clipped into position.
Pull to remove.
B -Bayonet bulbs: remove from the
bulb holder by pressing the bulb and
turning it anticlockwise.
C-D -Halogen bulbs: to remove the
bulb, release the clip holding the bulb
in place.
E -Xenon bulbs.
fig. 12
F0B0127b

IN AN EMERGENCY
162
IF AN EXTERIOR
LIGHT BURNS OUT
Modifications or repairs
to the electrical system
carried out incorrectly
and without bearing the features
of the system in mind can cause
malfunctions with the risk of fire.
IMPORTANTSee “If a bulb burns
out” for information on bulb types and
power when changing a bulb.FRONT LIGHT CLUSTER
Front headlights include front side
lights, main beam headlights, dipped
beam headlights, direction indicators
and front fog lights fig. 13:
A- main beam headlights;
B- front side lights;
C- dipped beam headlights;
D- direction indicators;
E- front fog lights.To replace a dipped beam headlight
remove the rubber cover 1-fig. 14by
turning it anticlockwise.
To replace front side lights and main
beam headlights remove the cover 2
by turning it anticlockwise.
To replace front fog lights remove the
cover 3by turning it anticlockwise.
To replace direction indicator bulbs
remove the bulb holder 4by turning
it anticlockwise.
fig. 13
F0B0130b
fig. 14
F0B0131b

IN AN EMERGENCY
163
FRONT SIDE LIGHTS fig. 15
To replace a bulb:
– Remove the cover as 2previously
described.
– Remove the bulb holder Aby turn-
ing it slightly.
– Take off the clipped bulb Band re-
place it.
– Put the bulb holder back to its
place.MAIN BEAM HEADLIGHTS
fig. 16
To replace a bulb:
– Remove the cover as 2previously
described.
– Disconnect the electrical connec-
tion A.
– Release clip B.
– Take off bulb Cand replace it.
– Fit the new bulb by matching the
metal tab with the groove on the lamp.
– Refit clip B.
– Reconnect connector A.DIPPED BEAM HEADLIGHTS
With halogen bulbs fig. 17
To replace a bulb proceed as follows:
– Remove the rubber cap 1as de-
scribed previously.
– Turn the bulb holder Aclockwise
or counter-clockwise to release it
from the catches.
– Remove the snap fitted bulb Band
replace it
fig. 15
F0B0135b
fig. 16
F0B0134b
fig. 17
F0B0446b

IN AN EMERGENCY
164
– Fit the new bulb into the bulb hold-
er (with protrusion facing upwards),
push the bulb forwards along the ve-
hicle axis until hearing the locking click
that indicates proper bulb securing.
– Refit the bulb holder into its seat
turning it clockwise or counter-clock-
wise to lock it to catches.
Xenon bulbs fig. 18
We recommend you to
have the bulb changed at
a Fiat Dealership.IMPORTANT The bulb replace-
ment procedure is described only as
information.
To replace a bulb:
– Remove the rubber cap 1as pre-
viously described.
– Release clip A.
– Disconnect connector B.
– Take off bulb Cand replace it.
– Fit the new bulb and connect con-
nector B.
– Refit clip A.Only touch the metal
part when handling
Xenon bulbs. If you touch
the transparent bulb accidental-
ly, rub it with a cloth moistened
with alcohol and leave it to dry.
fig. 18
F0B0129b

IN AN EMERGENCY
165
FRONT DIRECTION
INDICATORS fig. 19
To replace a bulb:
– Turn the bulb holder Aanticlock-
wise and remove it.
– Remove bulb Bby pushing it slight-
ly and turning it anticlockwise (bayo-
net coupling).
– Replace the bulb.
– Refit the bulb holder by turning it
clockwise and check it is well fastened.FRONT FOG LIGHTS fig. 20
To replace a bulb:
– Remove cap 3as previously de-
scribed.
– Disconnect connector A.
– Release clip B.
– Take off bulb Cand replace it.
– Fit the new bulb by matching the
metal tab with the groove on the lamp.
– Refit clip B.
– Reconnect connector A.SIDE DIRECTION
INDICATORS fig. 21-22
To replace a bulb:
– Press the lens Ain direction 1so
to compress the inside clip B, then
remove the unit by pulling it in direc-
tion 2.
– Turn bulb holder C anticlockwise.
– Take off clipped bulb Dand replace
it.
– Refit bulb holder Cand the trans-
parent unit.
fig. 19
F0B0136b
fig. 20
F0B0132b
fig. 21
F0B0128b

IN AN EMERGENCY
167
– Take off the bulb holders by turn-
ing them slightly anticlockwise fig. 26:
A- Direction indicator bulb;
B- Brake light/taillight bulb;
C- Reversing light bulb;
D- Rear fog light bulb.– Remove the bulbs by pushing them
slightly and turning them anticlockwise
as shown in the figure.
– After replacement, refit the bulb
holder by turning it clockwise and
check it is well fastened.
– Refit the unit and drive in wing nut
D(outside) and the two inside fas-
tening devices C.
– Reconnect the electrical connec-
tor Band refit finish A.NUMBER PLATE LIGHTS
fig. 27
The number plate lights are next to
the tailgate handle (one for each side).
To replace a bulb:
– Remove the clipped transparent
unit Aas shown in the figure.
– Take off clipped bulb Band replace
it.
– Refit the transparent unit.
fig. 26
F0B0138b
fig. 27
F0B0144bfig. 25
F0B0263b

IN AN EMERGENCY
174
FUSEBOX IN THE GLOVE COMPARTMENT fig. 37
1
2
4
5
7
9
10
11
12
14
15
16
17
18
20
22
23
24
2610A
15A
15A
10A
20A
30A
20A
15A
10A
30A
30A
5A
15A
10A
10A
10A
15A
15A
40ARear fog lights
Rear heated window
Main electronic control unit power supply
Left brake light
Spot light, cigar lighter, glove compartment light on passenger’s side,
automatic rear view mirror
Front sunroof, front windscreen wipers
Diagnosis socket
Electronic alarm, infotelematic Connect system, sound system,
multifunction display, steering column controls, particulate filter
Right side light, number plate lights, climate system control lights, ceiling lights
(first, second and third row)
Door locking system, Super door lock
Rear window wiper
Air bag system power supply, main electronic control unit power supply
Right brake light, third brake light, trailer brake lights
Diagnosis socket power supply, brake and clutch pedal switch
Sound system power supply for main electronic control unit
Left side light; trailer side light
Electronic alarm siren
Parking sensor power supply for main electronic control unit
Heated rear window