2007 FIAT PANDA Electrical

72
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IMPORTANT After eliminating the in-
convenience, to check the system com-
pletely, Fiat Dealerships are obliged to run
a bench test and, if necessary, road tests
which may also call for a long journey.
“DUALDRIVE” ELECTRIC
POWER STEERING
SYSTEM
(where provided)
Certain versions feature a new electrical-
ly controlled power steering system called
“Dualdrive” working only with ignition key
at MARand engine running, that can be
customised by the driver according to the
driving conditions.
IMPORTANT When turning quickly the
ignition key, power steering full operation
is obtained after 1-2 seconds.
EOBD SYSTEM (petrol
versions)
The EOBD system (European On Board
Diagnosis) allows continuous diagnosis of
the components of the car correlated with
emissions. It also alerts the driver, by turn-
ing on the warning light
Ufig. 91on the
instrument panel together with relevant
message on the reconfigurable multifunc-
tion display (where provided), when these
conditions are no longer in peak condi-
tions (see section “Warning lights and
messages”).
The objective is:
❒to keep the system efficiency under
control;
❒warn when a fault causes emissions lev-
els to increase;
❒warn of the need to replace deterio-
rated components.
The system has a diagnostic connector
that can be interfaced with appropriate
tools, which makes it possible to read the
error codes stored in the control unit, to-
gether with a series of specific parameters
for engine operation and diagnosis.
This check can also be performed by traf-
fic controller agents.
fig. 91F0G0161m
If turning the ignition key to
MAR, the warning light Udoes not turn on or if, while
travelling it turns on glowing
steadily or flashing (together with the
message on the reconfigurable multi-
function display (where provided), con-
tact Fiat Dealership as soon as possi-
ble. Warning light
Uoperation can be
checked by means of special equip-
ment by traffic agents. Always comply
with the traffic regulations in force in
the country where you are travelling.
060-080 Panda New GB 21-06-2007 13:48 Pagina 72

76
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SOUND SYSTEM PRESETTING
(where provided)
In addition to what provided with the stan-
dard set-up, the car is also fitted with:
❒two full range speakers, 165 mm diam-
eter, 40 W power each on front doors;
❒two full range speakers, 130 mm diam-
eter, 35 W power each on rear doors;
❒aerial power wire;
❒front and rear speaker power wires;
❒sound system power wires;
❒aerial on the car roof.SOUND SYSTEM
(where provided)
The complete system consists of the fol-
lowing:
❒two full range speakers, 165 mm diam-
eter, 40 W power each on front doors;
❒two full range speakers, 130 mm diam-
eter, 35 W power each on rear doors;
❒aerial on car roof;
❒radio with tape-recorder or sound sys-
tem with CD player or sound system
with MP3 CD player (for its operation
and characteristics see the “Sound sys-
tem” supplement attached to the pre-
sent Handbook).
With HiFi system (if required):
❒two tweeters A-fig. 97and two
woofers B, 40 W max power each on
front doors;
❒two full range speakers, 40 W max
power each on rear doors;
❒a subwoofer, 100 W power, under the
right seat;
❒aerial on the roof;
❒sound system with CD player or sound
system with MP3 CD player (for its op-
eration and characteristics see the
“Sound system” supplement attached
to the present Handbook). If after buying the car, you
decide to install a sound sys-
tem, contact Fiat Dealership
whose qualified personnel will
help you choose a sound system that
does not damage the battery charge.
Excessive electrical absorption dam-
ages the battery and makes its war-
ranty no longer valid.
fig. 96F0G0071m
SOUND SYSTEM
When the sound system has not been re-
quested the car is provided with two odd-
ment compartments on the instrument
panel.
STANDARD SOUND SYSTEM
fig. 96
The system consists of:
❒sound system power wires;
❒oddment compartment;
❒front and rear speaker compartments.
Remove the door panel to fit the speak-
ers.
Have this operation carried out at a Fiat
Dealership.
The sound system is to be fitted in the
dedicated seat in the oddment compart-
ment which can be removed by pressing
the two retaining tabs A.
Here you can find power wires.
060-080 Panda New GB 21-06-2007 13:48 Pagina 76

77
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
INSTALLATION OF ELECTRIC/
ELECTRONIC DEVICES
Electric/electronic devices installed after
buying the vehicle or in aftermarket shall
bear the and marking:
Fiat Auto S.p.A. authorizes the installation
of transceivers provided that installation
is carried out at a specialized shop, work-
manlike performed and in compliance with
manufacturer's specifications.
IMPORTANT Installation of devices re-
sulting in modifications of vehicle charac-
teristics may cause driving license seizing
by traffic agents and also the lapse of the
warranty as concerns defects due to the
abovementioned modification or traceable
back to it directly or indirectly.
Fiat Auto S.p.A. declines all responsibility
for damages caused by the installation of
non-genuine accessories or not recom-
mended by Fiat Auto S.p.A. and installed
not in compliance with the specified re-
quirements.RADIO TRANSMITTERS
AND CELLULAR TELEPHONES
Radio transceiver equipment (e.g.: HAM
radio systems and the like) shall not be
used inside the vehicle unless a separate
aerial is mounted on the roof.
IMPORTANT The use of similar devices
inside the passenger compartment (with-
out separated aerial) produces radio-fre-
quency electromagnetic fields which, am-
plified by the resonance effects inside the
passenger compartment, may cause elec-
trical systems equipping the vehicle to mal-
function. This could compromise safety in
addition to constituting a potential hazard
for the passengers.
In addition, transmission and reception of
these devices may be affected by the
shielding effect of the vehicle body.
As concerns EC-approved mobile phones
(GSM, GPRS, UMTS), strictly comply with
the instructions for use provided by the
mobile phone’s manufacturer. ACCESSORIES PURCHASED
BY THE OWNER
If after buying the car, you decide to install
electrical accessories that require a per-
manent electric supply (alarm, satellite an-
titheft system, etc.) or accessories that in
any case burden the electric supply, con-
tact Fiat Dealership, whose qualified per-
sonnel, besides suggesting the most suit-
able devices belonging to Lineaccessori Fi-
at, will also evaluate the overall electric ab-
sorption, checking whether the car’s elec-
tric system is able to withstand the load
required, or whether it needs to be inte-
grated with a more powerful battery.
fig. 97F0G0073m
060-080 Panda New GB 21-06-2007 13:48 Pagina 77

Accessories installed on
longitudinal bars
Remove accessories like: roof racks, ski
racks, luggage container, etc. from the roof
as soon as they are no longer used. These
accessories lower air penetration and ad-
versely affect consumption levels. When
needing to carry particularly voluminous
objects, preferably use a trailer.
Electric devices
Use electric devices only for the amount
of time needed. Rear heated window, ad-
ditional headlights, windscreen wipers and
heater fan need a considerable amount of
energy, therefore increasing the require-
ment of current increases fuel consump-
tion (up to +25% in the urban cycle).
Climate control
The air conditioner is an additional load
which greatly affects the engine leading to
higher consumption (on average up to
+20%). When the temperature outside
the car permits it, use the air vents where
possible.
Spoilers
The use of non-certified aerodynamic
items may adversely affect air drag and
consumption levels.DRIVING STYLE
Starting
Do not warm the engine with the car at
a standstill or at idle or high speed: under
these conditions the engine warms up
much more slowly, increasing electrical
consumption and emissions. It is therefore
advisable to move off immediately, slow-
ly, avoiding high speeds: this way the en-
gine will warm faster.
Unnecessary actions
Avoid accelerating when waiting at traffic
lights or before switching off the engine.
This and also double declutching is ab-
solutely pointless on modern cars and al-
so increases consumption and pollution.
Gear selection
As soon as the conditions of the traffic and
road allow, use a higher gear. Using a low
gear to obtain brilliant performance in-
creases consumption.
In the same way improper use of a high
gear increases consumption, emissions an
engine wear.CONTAINING
RUNNING COSTS
Some useful tips are given below for fuel
saving and reducing harmful emissions of
CO
2and other pollutants (nitrogen ox-
ides, unburnt hydrocarbons, Particulate
Matter (PM) etc.).
GENERAL CONSIDERATIONS
Car maintenance
Have checks and adjustments carried out
in accordance with the “Service schedule”.
Tyres
Check the pressure of the tyres routine-
ly at an interval of no more than 4 weeks:
if the pressure is too low, consumption
levels increase as resistance to rolling is
higher.
Unnecessary loads
Do not travel with too much luggage
stowed in the boot. The weight of the car
(especially when driving in town) and its
trim greatly affects consumption and sta-
bility.
106
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
101-112 Panda New GB 21-06-2007 13:50 Pagina 106

INSTALLING THE TOW HOOK
The towing device should be fastened to
the body by specialised personnel accord-
ing to any additional and/or integrative in-
formation supplied by the Manufacturer of
the device.
The towing device must meet current reg-
ulations with reference to 94/20/CEE Di-
rective and subsequent amendments.
For any version the towing device used
must match the towable weight of the car
on which it is to be installed.
For the electric connection a unified con-
nector should be used which is generally
placed on a special bracket normally fas-
tened to the towing device, and a special
ECU for external trailer light control shall
be installed on the car.
For the electric connection, a 7 pin
12VDC connection is to be used (CU-
NA/UNI and ISO/DIN Standards). Follow
the instructions provided by the car man-
ufacturer and/or the tow hitch manufac-
turer.An electric brake should be supplied di-
rectly by the battery through a cable with
a cross section of no less than 2.5 mm
2.
IMPORTANT Electric brake or other de-
vice shall be used with running engine.
In addition to the electrical branches, the
car electric system can only be connect-
ed to the supply cable for an electric brake
and to the cable for an internal light,
though not above 15W.
For connections use a preset control unit
with battery cable no less than 2.5 mm
2. Do not exceed the speed limits of the
country you are driving in. In any case do
not exceed 100 km/h.
108
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
The ABS system with which
the car may be fitted does
not control the trailer braking system.
Therefore be cautious on slippery
roads.
WARNING
Under no circumstances
should the car brake system
be altered to control the trailer brake.
The trailer braking system must be
fully independent of the car’s hy-
draulic system.
WARNING
101-112 Panda New GB 21-06-2007 13:50 Pagina 108

Proceed as follows:
❒ Connect positive terminals (+) of the
two batteries with a jump lead;
❒With a second lead, connect the nega-
tive terminal–of the auxiliary battery
to an earthing pointEon the engine or
the gearbox of the car to be started;
❒Start the engine;
❒ When the engine has been started, re-
move the leads reversing the order
above.
If after a few attempts the engine does not
start, do not insist but contact the near-
est Fiat Dealership.
IMPORTANT Do not directly connect the
negative terminals of the two batteries:
any sparks may ignite the detonating gas
which could come out of the battery. If the
auxiliary battery is installed on another
car, avoid metal parts touching acciden-
tally between this car and the one with the
flat battery. JUMP STARTING fig. 1
If the battery is flat, it is possible to start
the engine using an auxiliary battery with
the same capacity or a little higher than
the flat one.
fig. 1
125
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
Never use a battery charger
to start the engine as this
could damage the electronic
systems of your car, particu-
larly the ignition and fuel supply con-
trol units.
The starting procedure must
be carried out by qualified
personnel because incorrect opera-
tions may cause electrical discharge of
considerable intensity. The liquid con-
tained in the battery is poisonous and
corrosive. Avoid contact with the skin
and eyes. Keep naked flames and light-
ed cigarettes away from the battery
and do not cause sparks.
WARNING
F0G0694m
123-154 Panda New GB 21-06-2007 13:51 Pagina 125

BUMP STARTING
Never bump start the engine (by pushing,
towing or coasting downhill).
This could cause fuel to flow into the cat-
alytic converter and damage it beyond re-
pair.
IMPORTANT Remember that the servo-
brake and electrical power steering sys-
tem (where provided) are not operating
until the engine is started, a greater effort
will therefore be required to press the
brake pedal or turn the steering wheel.
126
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
The space-saver spare wheel
(where provided) is specific
to your car, do not use it on other
models, or use the spare wheel of oth-
er models on your car. The space-
saver spare wheel shall only be used
in an emergency. It shall only be used
for the distance necessary to reach a
service point and the car speed shall
not exceed 80 km/h. The spare wheel
has an orange sticker that summaris-
es the main cautions for use and lim-
itations. The sticker should never be
removed or covered. Never fit a wheel
cap on a space-saver spare wheel.
The sticker gives the following infor-
mation in four languages: Caution!
For temporary use only! 80 km/h max!
Replace by normal wheel as soon as
possible. Do not cover this label in
use.
If you change the type of wheel (al-
loy rims instead of steel rims) you will
have to change the entire set of fas-
tening bolts with another set of suit-
ably sized bolts.
WARNINGIF A TYRE
IS PUNCTURED
GENERAL INSTRUCTIONS
The car can be delivered (upon re-
quest/where provided) with standard
spare wheel or space saver spare wheel;
see changing instructions on the following
paragraphs.
Wheel changing and correct use of the
jack and space-saver spare wheel call for
some precautions as listed below.
123-154 Panda New GB 21-06-2007 13:51 Pagina 126

147
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
FUSE LOCATION
The fusebox is on the steering wheel left-
hand sidefig. 46and 47.
To gain access to the fusebox, slacken the
cover Ffastening screw E.
Gwired control unit.
HBody-computer control unit.
Dfuse extracting pliers.
The number identifying the electrical com-
ponent corresponding to each fuse is on
the cover back.
fig. 47 fig. 46
F37
18
916
F0G0139m
F0G0260m
123-154 Panda New GB 21-06-2007 13:51 Pagina 147