2007 FIAT PANDA spare wheel

4
FIAT PANDA 4 x 4
IF A TYRE
IS PUNCTURED
General instructions
The car can be delivered (upon request/if
provided) with space-saver spare wheel
or with quick tyre repair kit (called Fix &
Go).
Wheel changing and correct use of the jack
and space-saver spare wheel call for some
precautions as listed in the Owner Hand-
book this Supplement is attached to. In the
Owner Handbook you will also find how
to use the Fix & Go kit (quick tyre repair
kit).
To change a wheel proceed as follows:
❒stop the car in a position that is not
dangerous for oncoming traffic where
you can change the wheel safely. The
ground should be flat and adequately
firm;
❒turn the engine off and pull up the hand-
brake;
❒engage first gear or reverse;
❒take out the tool bag fig. 3set under the
driver’s seat and take it near the wheel
to be changed;
❒loosen the clamping device B-fig. 4;
❒take the space-saver spare wheel A;
❒loosen the bolts on the wheel to be
replaced with the wrench provided A-
fig. 5;
❒turn the jack handle to open it partly;
❒place the jack near the wheel to be
changed in line with mark Oon the
sidemember fig. 6;
❒make sure the groove Fon the jack fits
correctly into the sidemember ridge G;
❒alert other passengers that the car is
about to be raised; all persons should
be kept away from the car until it has
been lowered again;
fig. 3F0G0607m
fig. 4F0G0608m
fig. 5F0G0609m
fig. 6F0G0610m
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 4

5
FIAT PANDA 4 x 4
❒fit handle H-fig. 6to the jack device I
and raise the car until the wheel is a few
inches off the ground. When turning the
jack handle make sure that it can be used
easily and take care not to scrape your
hand against the ground. The moving
parts of the jack (screws and joints) may
also cause injury if touched. Clean off any
grease;
❒remove the wheel cap (if any) after un-
screwing the three relevant bolts then,
unscrew the fourth bolt L-fig. 7 and re-
move the wheel;
❒make sure the space-saver spare wheel
supporting surfaces on the hub are
clean and free from any impurities that
could cause wheel bolts loosening;
❒fit the space-saver spare wheel match-
ing one of the wheel holes Owith pins
N-fig. 8;
❒fasten the four fastening bolts;
❒turn the jack handle to lower the car
and remove the jack;
❒fasten the bolts completely, working in
a criss-cross fashion as shown in fig. 9.
fig. 7F0G0233mfig. 8F0G0204mfig. 9F0G0206m
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 5

6
FIAT PANDA 4 x 4
After changing the wheel
❒put the jack partly open and the tools
used into the tool bag;
❒stow the bag with tools into its place
under the driver’s seat.
IMPORTANT Replaced wheel shall be
placed in the boot under the cover mat as
shown in fig. 10.
IMPORTANT Do not use inner tubes
with tubeless tyres. Check tyre and space-
saver spare wheel pressure regularly.IMPORTANT Changing original wheels
with others of different type (i.e.: with al-
loy rim instead of steel rims and vice ver-
sa) will involve to change the whole set
of wheel bolts with others of suitable
length. It is however recommended to
keep replaced bolts in the event of future
refitting of the original wheels.
fig. 10F0G0615m
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 6

15
FIAT PANDA 4 x 4
To prevent damages to the
viscous joint do not cover long
distances with underinflated
tyres (tyres partly or com-
pletely flat).
RIMS AND TYRES
All Fiat Panda 4x4 version tyres have been designed to obtain best performance on both regular roadbed and not asphalted and/or
snowy or icy roads.
These tyres are characterised by high road-holding performance off-road and good driveability on both snowy/icy roads and dry or
wet roadbeds.
The following tyres are provided:
5.5J x 14
5.5J x 14
5.5J x 14
6J x 15
165/70 R14 81T M+S
185/65 R14 86T M+S ()
165/70 R14 81T M+S (*)
185/65 R14 86T M+S
175/65 R15 84T M+S (*) ()4.00B x 14
4.00B x 14
4.00B x 14
4.00B x 15135/80 R14 84P
135/80 R14 84P
135/80 R14 84P
125/80 R15 95M Fiat Panda 4 x 4
Fiat Panda 4 x 4
Climbing
Fiat Panda 4 x 4
CROSS Version Rims Tyres Space-saver spare wheel
Rim Tyre
(*) Optional tyre
() Tyres that cannot be fitted with snow chains
Versions Medium load Full load Space-saver
front rear front rearspare wheel
1.22.2 2.0 2.3 2.3 2.8
1.3 Multijet2.3 2.1 2.3 2.3 2.8 / 4.2(*)
(*) For Fiat Panda 4 x 4 CROSS versions with 125/80 R15 95M
space-saver spare wheel
INFLATION PRESSURES (bar)
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 15

21
FIAT PANDA 4 x 4
Fiat Panda 4 x 4Fiat Panda 4 x 4
ClimbingFiat Panda 4 x 4
CROSS
WEIGHTS
Weights (kg)
Kerb weight
(including fuel, space-saver
spare wheel, tools and accessories):
Payload (*)
including the driver:
Maximum admitted loads (**)
– front axle:
– rear axle:
– total:
Towable loads
– trailer with brakes:
– trailer without brakes:
Maximum load on roof (***):
Maximum load on tow hitch
(trailer with brakes):
(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen car weight increases, thus reducing the payload as specified
in the max. admitted loads.
(**)Loads not to be exceeded. The driver is responsible for arranging the loads in the boot and/or on the
roof so that they comply with these limits.
(***) Lineaccessori Fiat roof rack, max. capacity: 50 kg.petrol Multijet
965 1060
445 445
750 825
735 735
1410 1505
800 900
400 400
50 50
60 60petrol Multijet
980 1075
445 445
750 825
735 735
1425 1520
800 900
400 400
50 50
60 60Multijet
1090
445
830
735
1535
900
400
50
60
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 21