2007 FIAT IDEA dashboard

❒make sure the compressor switch Dis set to 0 (off), start the engine
and fit plug Einto the nearest current outlet and then turn on the com-
pressor by setting switch D to I(on). Inflate the tyre to the pressure spec-
ified in paragraph “Inflation pressure” in section “Technical Specifications”.
Check tyre pressure on gauge Fwith compressor off to obtain precise read-
ing;
❒if after 5 minutes it is still impossible to reach at least 1.5 bar, disengage
compressor from valve and current outlet, then move the car forth for
approx. ten metres in order to distribute the sealing fluid inside the tyre
evenly, then repeat the inflation operation;
❒If after this operation it is still impossible after 5 minutes to reach at least
1.8 bar, do not start driving since the tyre is excessively damaged and
the quick tyre repair kit cannot guarantee suitable sealing, contact Fiat
Dealership;
228
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
F0H0357m
F0H0177m
F0H0358m
WARNINGIf the pressure falls below 1.8 bars, do not
drive any further: the quick tyre repair kit
Fix & Go automatic cannot guarantee
proper hold because the tyre is too much
damaged. Contact Fiat Dealership.
WARNING
Apply the sticker in a visible position for the
driver to indicate that the tyre has been
treated with the quick tyre repair kit. Drive
carefully especially when cornering. Do not
exceed 80 km/h. Avoid heavy braking and
accelerating.

229
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
It is of vital importance to communicate that the tyre has been repaired using the
quick tyre repair kit. Hand the instruction brochure to the personnel charged with
treating the tyre repaired with the kit.WARNING
❒if reaching the tyre pressure specified in paragraph “Inflation pressure”
in section “Technical Specifications”, start driving immediately;
❒after driving for about 10 minutes stop and check again the tyre pres-
sure; pull up the handbrake;
❒if at least 1.8 bar pressure is read, restore proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the nearest Fiat Dealership.
FOR CHECKING AND RESTORING PRESSURE ONLY
The compressor can be also used just for restoring pressure. Disconnect
the quick connection and connect it directly to the tyre valve; in this way the
cylinder is not connected to compressor and the sealing fluid will not flow
into the tyre.
CYLINDER REPLACEMENT PROCEDURE
To replace the cylinder proceed as follows:
❒disconnect connection A;
❒turn counter-clockwise the cylinder to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection Ato the cylinder and fit the transparent tube Bin-
to the proper space.
F0H0359m
F0H0360m

IF A TYRE IS PUNCTURED
GENERAL INSTRUCTIONS
Wheel changing and correct use of the jack and space-saver spare wheel call for some precautions as listed below.
WARNING If the car is equipped with “Kit for tyre quick repair Fix & Go”, see the instructions contained in the
following chapter.
230
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
WARNINGThe space-saver spare wheel is specific to the vehicle: do not use it on other
models and do not use spare wheels designed for other models on your car. The
space-saver spare wheel must only be used in the event of an emergency, and then
only for as little as possible and at no more than 80 km/h. The space-saver spare
wheel is fitted with an orange sticker giving the main instructions for its use and
limitations. The sticker must never be removed or covered. Do not fit the hub cap
to the spare wheel. The sticker gives the following information in four languages:
C
AUTION! FOR TEMPORARY USE ONLY! 80 KM/H MAX! REPLACE BY NORMAL WHEEL AS SOON
AS POSSIBLE
. DO NOT COVER THIS LABEL IN USE.

231
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
WARNINGThe jack should only be used to change a wheel on the car for which it was
designed. It should not be put to other uses or employed to raise other models of
cars. Under no circumstances should it be used when carrying out repairs under the
car. An incorrectly positioned jack may cause the car to fall. Do not use the jack to
lift loads exceeding that indicated on the label attached to the jack itself. Do not
fit snow chains on a space-saver spare wheel. If a front wheel (drive wheel) is
punctured and you require snow chains to proceed, take a standard wheel from
the rear axle and fit the space-saver spare wheel in its place. Having fitted two
standard wheels on the front drive axle you can use snow chains, thus solving the
emergency situation.
WARNINGWhen driving with a space-saver spare wheel fitted, the driving performance of
your car may change. Avoid accelerating or braking suddenly, steering abruptly or
fast cornering. The lifespan of a space-saver spare wheel is approximately 3000
km, after which it will need to be replaced with another spare wheel of the same
type. Never fit a standard tyre on the space-saver spare wheel rim. Have the wheel
replaced and refitted as soon as possible. Never use two or more spare wheels at
the same time. Do not lubricate the bolt threads before fitting them back: they
could come loose.
WARNINGFasten the wheel cap correctly to prevent the wheel from coming free in motion.
Never tamper with the inflation valve. Never place tools between the rim and tyre.
Check the tyre and space-saver spare wheel pressure regularly. The tyre inflation
pressure is shown in the “Technical specifications” chapter.

232
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
Please note:
❒the jack cannot be repaired. If it breaks it must be replaced with a
new jack;
❒no tool other than its cranking device may be fitted on the jack.
To change a wheel proceed as follows:
❒Stop the car in a position that is not dangerous for oncoming traffic
where you can change the wheel safely. The ground should be flat and
adequately firm;
❒Turn the engine off and pull up the handbrake;
❒Engage first gear or reverse;
❒Lift the luggage compartment panel mat;
❒Loosen the fastener (A);
❒Take the tool bag (B) and go to the wheel to be replaced;
❒Take the space-saver spare wheel (C);
❒If the car is fitted with alloy rims, remove the wheel hub with the
screwdriver provided levering in the groove (E), as shown in the
figure;
F0H0161m
F0H0162m

233
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
F0H0163m
❒Loosen the bolts on the wheel to be replaced by about one turn with
the wrench provided (E); if the car is fitted with alloy rims, shake the
car to facilitate removing this rim from the wheel hub;
❒Operate the device (F) and extend the jack until groove (G) on the
jack fits correctly into ridge (H) on the body near sign I (at about 60
cm from the front wheel centre or 80 cm from the rear wheel
centre);

234
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
❒Warn anybody nearby that the car is about to be
lifted. They must stay clear and not touch the
vehicle until it is back on the ground;
❒Fit the handle (L) to operate the jack and lift the
car until the wheel to be changed is several
centimetres off the ground;
F0H0164m
❒For versions with wheel cap, remove the wheel cap
after unloosing the three fastening bolts and finally
unloose the fourth bolt and extract the wheel.
❒Make sure the contact surfaces between spare
wheel and hub are clean so that the fastening bolts
will not come loose;

235
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
F0H0165m
F0H0166m
❒Fit the spare wheel making the holes (M) coincide with the respective
centring pins (N);
❒Using the wrench provided, fully tighten the four fastening bolts;
❒Turn the jack handle (L) to lower the car and remove the jack;
❒Use the wrench provided to fasten the bolts completely in a criss-
cross fashion as shown in the figure.
REFITTING THE STANDARD WHEEL
Following the procedure described previously, raise the car and remove
the spare wheel.
For versions with steel rim
Proceed as follows:
❒Make sure the contact surfaces between standard wheel and hub are
clean so that the fastening bolts will not come loose;
❒Fit the standard wheel by inserting the first bolt in the hole closest to
the inflation valve;
❒Fit the wheel cap making the groove (on the wheel cap) coincide with
the inflation valve and fit the other three bolts;
❒Using the wrench provided, tighten the fastening bolts;
❒Lower the car and remove the jack;
❒Using the wrench provided, fully tighten the bolts in the sequence
shown previously for the spare wheel;
IMPORTANT Incorrect fitting may cause the wheel cap to come off
when the car is travelling.