2007 FIAT GRANDE PUNTO sat nav

5656
Using the phone during the
updating procedure
During the updating procedure it is how-
ever possible to make or answer a call.
Blue&Me™ Navwill pause the updating
procedure and resume it at the end of the
phone conversation automatically.
To make or answer a call during the up-
dating procedure using manual interaction,
refer to sections MAKING A PHONE
CALL and INCOMING CALLS.
The updating procedure will be paused au-
tomatically.
Ending the phone call will resume the up-
dating procedure automatically.Resuming the update
If the updating procedure is paused using
the settings menu option, the updating pro-
cedure shall be then resumed manually.
To resume the updating procedure using
manual interaction, proceed as follows:
❒Your mobile phone shall be paired with
Blue&Me™ Nav.
❒Press ß/MAINand move to SET-
TINGS, RESUME UPDATE(this
menu option is available only if update
has been previously paused). Press
SRC/OKor
ß/MAIN.
❒Blue&Me™ Navwill display the mes-
sage RESUME UPDATEand say
“Update. On completion, a mes-
sage will appear”.
If the updating procedure was paused be-
cause the ignition key has been turned to
“STOP”, the updating procedure will be
resumed automatically. Notes
❒Updates will be resumed automatical-
ly only if using the same mobile phone
used for starting the updating proce-
dure.
❒Blue&Me™ Navwill pause automati-
cally the updating procedure if the paired
mobile phone is no longer available, or
if updating is paused by the Service Cen-
tre, if communication is stopped (e.g.:
tunnels), or if the system slows down
too much its working speed.
Blue&Me™ Navwill try to resume up-
dating at preset time intervals. Should
it be not possible to resume updating
while driving, updating will be resumed
at next engine starting.
❒If you encounter difficulties with
any of these operations, consult
section HANDS-FREE KIT - TROU-
BLESHOOT-ING.
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 56

6161
Due to the different marketed software
versions for mobile phones, certain auxil-
iary functions (e.g.: answering a second in-
coming phone call, transferring phone call
from hands-free phone system to mobile
phone and vice versa, etc.) could not ex-
actly correspond to what described in this
manual. In any case, phone conversation us-
ing the hands-free phone kit is not impaired.
“Pull” phones (phonebook
automatically downloaded)
“Pull” phone means that your mobile
phone supports phonebook automatic
download with Bluetooth
®wireless tech-
nology, your whole phonebook will be au-
tomatically downloaded to Blue&Me™
Navduring phone pairing procedure. “Push” phones (phonebook not
automatically downloaded)
“Push” phone means that your mobile
phone supports the single contact down-
load with Bluetooth
®wireless technolo-
gy. During the pairing procedure you will
be required to send phonebook contacts
from your mobile phone (your phone-
book is not automatically downloaded
during the phone pairing procedure).Mobile phones with message
reader
If your mobile phone can send messages
through the Bluetooth
®wireless tech-
nology, it is possible to read incoming
messages through the Blue&Me™ Nav
hands-free kit, to store them in the dedi-
cated inbox or to delete them.
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 61

74
Call up one a recent
destination set
Set the type of route
• Recent destinations
➯continues
• Navigation
• Navigator
Activate the NAVIGATIONmenu
• Next maneuver
• Maneuver
• Next
• Next maneuver
Repeat the last voice message
during navigation
Use to set preferences for
the type of route
• Navigation settings
Provides an indication of
latitude, longitude and number
of GPS satellites visible
• Vehicle position
• Route simulation
• Simulation
Simulates the set route
• Type of route
• Type of route
• Set type of route
• Route
Include or exclude motorways
from the route calculation
• Set motorways
• Motorways
Include or exclude ferries
from the route calculation
• Set ferries
• Ferries
• Boats
Include or exclude toll roads from
the route calculation
• Set tolls
• Tolls
• Set toll
• Toll
Enable or disable completion
of the destination by voice.
• Dictate destination
• Dictate
• Dictate destination
Start navigating towards the
displayed destination
• Start
• Navigate
Display the next destination
in the list
• Forward
• Next
Display the previous desti-
nation in the list
• Back
• Previous
Delete the displayed
destination
• Delete
Delete all the destinations
in the list
• Delete all
Select the Picnic
Area category• Picnic area
Select the Train
Station category• Train Station
• Train station
• Trains
Select the Vehicle
Service category• Vehicle service
• Vehicle service
Select the Service
Station category
• Petrol station
• Service stations
• Petrol station
• Petrol stations
Select the
Chemist category• Chemist
• Chemists
Select the
Restaurant
category• Restaurant
• Restaurants
Select the Hotel
category• Hotel
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 74

7878
Problem Probable Cause Possible Solution
Display screen shows: NO PHONE
CONNECTED
Or the system says
“There’s no bluetooth phone connected”
Display screen shows: PHONE
DISCONNECTED
Display screen shows:PAIRING FAILED
Or the system says “Pairing failed.
Please try again”
❒Turn the paired mobile phone on
❒Make sure that your phone is paired
❒Make sure that the Bluetooth®
wireless technology connection on
your mobile phone is enabled
(“Blue&Me” or ID)
❒
Make sure that the mobile phone
you paired with the system is within
range
❒Reset Blue&Me™ Navby turning
the mobile phone off and on
❒Reset Blue&Me™ Navby turning
the ignition key to STOPand then
to MARagain
❒Verify the correct PIN number, and
try entering it again
❒Reset the mobile phone by turning it
off and on, and then retry the pairing
procedure
SETTING FUNCTIONS -
PAIRING YOUR MOBILE PHONE
❒The paired mobile phone is turned
off
❒The paired mobile phone is not
within range of the system
(the mobile phone should be located
within approximately 10 m of the
system)
❒Bluetooth®wireless technology
connection has been disabled on
your mobile phone
(“Blue&Me” ID)
❒
A technical error occurred
with the mobile phone
Bluetooth
®wireless technology
capabilities
❒
During an ongoing phone
conversation,the mobile phone
was taken out of the system range
❒A technical error occurred during
the pairing procedure
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 78

8686
Phone-specific: Nokia®
Problem Probable Cause Possible Solution
Before establishing a connection with
Blue&Me™ Navpaired Nokia
®mobile
phone, the phone display screen prompts
with a confirmation message
(e.g.:“Accept connection request)
During an active phone call on the
hands-free phone system of the car,
the Bluetooth
®wireless technology
connection is disconnected when pressing
button SRC/OKto switch the audio
output from the device to the mobile phone
Models: Nokia®6820, 6230, 7610 or 6600
While handling two phone conversations
via call waiting on a Nokia®mobile phone,when pressing SRC/OKto transfer audio output to the mobile phone, only one of the phone conversations is transferred
When pressing SRC/OKto switch the audio output of the phone conversation
from the Nokia®mobile phone to the hands-free kit, nothing happensOn your mobile phone navigate to
“Connectivity” →“Bluetooth
®”.
Select the next menu using the key
on the right side. Select “Blue&Me”
and then “Authorized”
The phone call is still active on the
mobile phone. If you wish to
reconnect and use the hands-free kit
again, press
ß/MAIN
–
Press
ß/MAINor ‘to reconnect
the phone conversation to the
hands-free feature Nokia
®mobile phones do not allow
Blue&Me™ Navto automatically
establish the Bluetooth
®wireless
technology connection
To establish connection you must set
your mobile phone
Pressing SRC/OKduring an active
phone call on this type of phone dis-
connects the Bluetooth
®wireless
technology connection
The ability to transfer audio output
for two active phone conversations
to the mobile phone is not supported
by the system when paired with a
Nokia
®mobile phone
–
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 86

8888
Problem Probable Cause Possible Solution
After receiving, answering and
ending a second call, the multifunction
display shows INCOMING CALL
PRIVATE NUMBER, instead of the
phone number corresponding to the
first call
Models: Nokia®6600
Sometimes when trying to use this phone
with Blue&Me™ Nav, using the
ß/MAIN
button, the message SEARCHING
CONNECTIONis displayed before
the connection is implemented
Models: Nokia®6600
No ring tone is produced when receiving
a second incoming call
Models: Nokia®6820
Pressing
ß/MAINfor over 1 second to
reject a second incoming call, disconnects
also the current phone conversation
Models: Nokia®6820
When answering an incoming call using
the mobile phone keypad, sometimes the
mobile phone disconnects from
Blue&Me™ Navand the phone
conversationhas to be continued on the
mobile phone instead of the hands-free
feature
Models: Nokia®7610
–
Wait for connection.
To prevent recurring of this problem,
reset the mobile phone by turning it
off and on again
The ring tone of the second incoming
call will always be lower than
normal. Try to turn up the ring tone
volume
–
Answer the incoming call by pressing
ß/MAIN In this specific case, the system is not
able to identify which phone call is
ended
The connection between this mobile
phone and Blue&Me™ Navsome-
times may deactivate
On this mobile phone the ring tone of
the second incoming call is very low
This behavior depends on the specific
features of this mobile phone
For certain software versions of this
mobile phone, answering a call using
the keypad will automatically
disconnect the mobile phone from the
hands-free kit
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 88

8989
Phone-specific: Sony-Ericsson®
Problem Probable Cause Possible Solution
Occasionally, Blue&Me™ Navdoes not
detect the mobile phone and it is unable
to make a hands-free phone call
Models: Sony–Ericsson
®Z600
When using call waiting to answer an
incoming call during an ongoing phone
call conversation, sometimes
Blue&Me™ Navdisconnects the
ongoing phone conversation
Models: Sony–Ericsson®T610
Downloading the phonebook from the
mobile phone to Blue&Me™ Nav
does not work
Models: Sony–Ericsson
®Z600
❒Reset the mobile phone by turning it
off and on again to restore
connection with Blue&Me™ Nav
❒Reset the mobile phone by turning it
off, removing the phone battery and
then placing it back in, and
then turning it on again
After you hang up the other phone call
that was received via call waiting, the
mobile phone displays a message that
asks if you wish to retrieve the call.
Confirm using the mobile phone key-
pad
Transfer your contact entries from the
SIM card to the mobile phone memory.
Delete the phonebook from
Blue&Me™ Nav, by selecting the
option DELETE PHONEBOOK.
Then download the phonebook again
selecting the option COPY PHONE-
BOOK
SETTING FUNCTIONS -
MANAGING USER DATA AND
PHONEBOOK –
–
This mobile phone can download
contact entries only if they are saved
on the phone memory
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 89