2007 DODGE SPRINTER buttons

107 Controls in detail
Operating system with steering wheel buttons*
3
Consumption statistics after reset
\1Press the è or ÿ button repeat-
edly until you see the
After start
mes-
sage in the display.
\1Press the j or k button repeat-
edly until you see the
After reset
mes-
sage.
1Distance driven since last reset
2Time elapsed since last reset
3Average speed since last reset
4Average fuel consumption since last
resetResetting the consumption statistics
\1Press the è or ÿ button repeat-
edly until you see the
After start
mes-
sage in the display.
\1Press the j or k button repeat-
edly until you see the statistics that you
want to reset in the display.
\1Press and hold the reset button un-
til the values are reset to 0.You can operate your cell phone using the
functions in the
TEL
menu, provided it is
connected to the manufacturer’s hands-
free system*.
N54.32-2275-31
iThe consumption statistics after start
are automatically reset after 999 hours
or 9,999 miles (kilometers).
The consumption statistics after reset
are automatically reset after 9,999
hours or 99,999 miles (kilometers).
Telephone menu
*
Warning
G
You must observe the legal requirements for
the country in which you are driving when
operating a cell phone in the vehicle.
If it is permitted to operate a cell phone
while the vehicle is in motion, you must only
operate it when road and traffic conditions
permit. You may otherwise be distracted
from the traffic conditions, cause an acci-
dent and injure yourself and others.
Cell phones without exterior antennas may
interfere with the vehicle electronics and
thereby jeopardize the operational safety of
the vehicle. You must therefore only use
these devices when they are connected to a
separate exterior antenna.

108 Controls in detailOperating system with steering wheel buttons*
3
\1Switch on the cell phone and audio sys-
tem or COMAND APS*.
See the separate operating instruc-
tions.
\1Press theè or ÿ button repeat-
edly until you see the
TEL
menu in the
display.
You will see different messages in the
display, depending on the status of
your cell phone:
\4If the cell phone is switched off, you
will see the
TEL off
message
(Sound 20) or
Tel Turn on
message
(COMAND APS*) in the display.
\4If you have not yet entered a PIN,
you will see the
TEL PIN
message
(Sound 20) or
Enter PIN
message
(COMAND APS*).
\1Enter the PIN code using the cell
phone, audio system or
COMAND APS*.The cell phone searches for a network. The
display remains blank during this time.
As soon as the cell phone has found a net-
work, you will see the
Ready
message in
the display.
Once it has shown its operational readi-
ness, you can operate the cell phone using
the operating system.
Rejecting a call
If you do not wish to speak to the person
who is calling, you can reject the call.
\1Press the t button.
The caller then hears the busy signal.Accepting a call
You can accept a call at any time, provided
the cell phone is ready to receive calls.
\1Press the s button.
The call duration is shown in the dis-
play.
Ending a call
\1Press the t button.
The display now shows the operational
readiness symbol again.
Dialing a number from the phone book
You may select and dial a number from the
phone book at any time, provided the cell
phone is ready to receive calls.
\1Press the è or ÿ button repeat-
edly until you see the
TEL
menu with
the operational readiness symbol in the
display. N54.32-2276-31
iIt is only possible to create new phone
number entries in the phone book us-
ing the cell phone itself. See the sepa-
rate operating instructions.

109 Controls in detail
Operating system with steering wheel buttons*
3
\1Press thej or k button.
The operating system reads the phone
book stored on the SIM card or in the
phone. This may take more than
1minute.
You will see the
Processing
message
(Sound 20) or
Wait...
message
(COMAND APS*) in the display.
\1Press the j or k button repeat-
edly until you see the name you are
looking for.
The stored names are displayed alpha-
betically from A to Z, or Z to A.
\1Press the s button.The operating system dials the select-
ed phone number. You will see the
dialing
message (Sound 20) or
Dial-
ing...
message (COMAND APS*) in
the display.
The operating system stores the phone
numbers in the redial memory.
If a connection is made, you will see the
name of the person you are calling and
the call duration.
Redialing
The operating system stores the most re-
cently dialed phone numbers. This means
that you do not have to search through the
entire phone book.
\1Press the ÿ or è button repeat-
edly until you see the
TEL
menu with
the operational readiness symbol in the
display.\1Press the s button.
The redial memory shows the most re-
cently dialed numbers or names.
\1Press the j or k button repeat-
edly until the number or the name you
are looking for is displayed.
\1Press the s button.
The operating system dials the select-
ed phone number.
If a connection is made, you will see the
call duration and name of the person
you are calling if stored in the phone
book. Otherwise, the number you are
dialing continues to be displayed.
iThe operating system scrolls through
the names rapidly if you press and hold
the j or k button for more than
one second. Releasing the button stops
the rapid scroll.
If you no longer wish to make a call,
press the t button.
iIf you no longer wish to make a call,
press the t button.

121 Controls in detail
Automatic transmission
3
\3 Automatic transmissionP Parking position (selector lever lock)
R Reverse gear
N Neutral
D Drive position
The automatic transmission adapts to your
individual driving style by continuously ad-
justing its shift points. These shift point ad-
justments take into account the current
operating and driving conditions.If the operating or driving conditions
change, the automatic transmission reacts
by adjusting the gearshift program.
The individual gears are selected automat-
ically. The gear selected depends on:
\4the selector lever position in shift rang-
es D, 4, 3, 2 and 1 (\2page 123)
\4the position of the accelerator pedal
(\2page 123)
\4the road speed
\4resistance (load, uphill gradient, trailer
towing)
The selector lever position engaged or the
current shift range is shown in the display.
Display on vehicles with steering wheel
buttons* (\2page 89) and on vehicles
without steering wheel buttons
(\2page 87).When the selector lever is in position D,
you can influence the gearshifts made by
the automatic transmission by:
\4restricting the shift range
\4changing gear yourselfGearshift patternGearshift procedure
Selector lever positionsì
Parking lock
Prevents the parked vehicle
from rolling away. Only move
the selector lever to P when
the vehicle is stationary.
You can only remove the key
when the selector lever is in
position P. The selector lever is
locked in position P when the
key is removed.
í
Reverse gear
Only move the selector lever to
R when the vehicle is station-
ary.

142 Controls in detailAuxiliary heating/ventilation*
3
Selecting a switch-on time
You can use the operating system to define
up to 3 switch-on times, one of which can
be selected to switch on the auxiliary
heating / ventilation.
Operating system without steering
wheel buttons
\1Switch on the ignition (\2page 67).
\1Press theö switch.
Theö symbol in the display flashes.
or
\1Press the menu button on the in-
strument cluster repeatedly until the
ö symbol in the display flashes.
\1Use the or button on the instru-
ment cluster to select desired switch-
on time
1 to
3.
The switch-on time selected is dis-
played.\1Wait 10 seconds for the standard dis-
play to appear.
The switch-on time is selected.
The yellow indicator lamp in theö
switch comes on.
If you have not selected a switch-on time
and
--:--
appears in the display, the auto-
matic switch-on is deactivated. The yellow
indicator lamp in theö switch goes
out.Operating system with steering wheel
buttons*
\1Switch on the ignition (\2page 67).
\1Briefly press theö switch.
The
Aux. heat.
submenu is shown in
the display.
The selected switch-on time is high-
lighted or
Timer off
is highlighted if no
switch-on time has been selected.
\1Press theæ orç button to se-
lect the desired switch-on time. The au-
tomatic switch-on is deactivated if the
Timer off
setting is selected.
iIf you turn the key to position0 in the
ignition lock, the yellow indicator lamp
in theö switch goes out after
30 minutes.
The red indicator lamp in theö
switch comes on when the auxiliary
heating switches on.
iYou can reach the
Aux. heat.
submenu
via the
Settings
menu (\2page 96).
N54.32-2277-31
\2\2

143 Controls in detail
Auxiliary heating/ventilation*
3
\1Press the è button.
The switch-on time is selected.
The yellow indicator lamp in theö
switch comes on.
Setting the switch-on time
Operating system without steering
wheel buttons
\1Select a switch-on time as described
under “Selecting a switch-on time”
(\2page 142).\1Press the reset button on the instru-
ment cluster to set the selected switch-
on time.
The hours figure flashes and the”
symbol appears in the display.
\1Set the hours using the or am
button on the instrument cluster.
\1Press the reset button.
The minute display flashes.
\1Set the minutes using the or
button.Operating system with steering wheel
buttons
\1Select a switch-on time as described
under “Selecting a switch-on time”
(\2page 142).
\1Press thej button.
The
Hours
menu appears in the display.
\1Set the hours using theæ orç
button.
\1Press thej button.
The
Minutes
menu appears in the dis-
play.
\1Set the minutes using theæ
orç button.
\1Press the è button.
The switch-on time is set and selected.
iIf you turn the key to position0 in the
ignition lock, the yellow indicator lamp
in theö switch goes out after
30 minutes.
The red indicator lamp in theö
switch comes on when the auxiliary
heating switches on.
iIf you keep the button pressed, the val-
ues will change continuously.
To return to the standard display:
\4press and hold the button on
the instrument cluster for more
than 1 second
\4do not press a button for
10 seconds
iTo return to the standard display, press
theè or ÿ button repeatedly
until the standard display appears.

154 Controls in detailOperating the vehicle
3
\3 Operating the vehicleWhen activated, the operating speed gov-
ernor (ADR) automatically increases the
engine speed to a preset or adjustable
operating speed (\2page 155).Activating / deactivating ADR
The switch is between the light switch and
the steering wheel.
1To switch on
2To switch off
\1To switch on: press upper part 1 of
the switch with the engine running.
The indicator lamp in the switch comes
on.
Vehicles without steering wheel but-
tons:
The™ indicator lamp in the instru-
ment cluster comes on.Vehicles with steering wheel buttons:
The
Operating speed governor active
message appears in the display.
\1To switch off: press lower part 2 of
the switch with the engine running.
The indicator lamp in the switch and
the™ indicator lamp in the instru-
ment cluster go out.
Operating speed governor (ADR)*iThe idle speed of the engine automati-
cally increases after a cold start. If the
set operating speed is lower than the
increased idle speed, the set operating
speed is attained only after the engine
has reached its operating temperature.
It is only possible to activate ADR with
the vehicle stationary and the hand-
brake applied. The selector lever must
be in position P.
N54.25-2932-31
iADR is automatically deactivated
when:
\4you release the handbrake
\4the vehicle moves
\4the control unit detects a malfunc-
tion

188 OperationEngine
4
Checking the engine oil level in the dis-
play
In vehicles with diesel engines, you can
view the engine oil level in the display.
When the oil is being checked, the vehicle
must
\4be standing level
\4be at normal operating temperature
\4have been standing with the engine
switched off for at least five minutes\1Switch on the ignition (\2page 67).
The display is activated.
Vehicles without steering wheel buttons
\1Press the menu button on the in-
strument cluster repeatedly until you
see the P symbol in the display.
The
--:--
display flashes during the
measurement process.The following messages may be displayed:
\1Check the engine oil level again after a
few minutes.
Vehicles with steering wheel buttons*
\1Press the button on the instrument
cluster (\2page 84).
iIf no oil level reading is shown again,
check the engine oil level with the dip-
stick.
Have the engine oil level display
checked at an authorized Sprinter
Dealer.!
CAUTION
Have any excess oil drained or si-
phoned off at an authorized Sprinter
Dealer. Otherwise, the engine or cata-
lytic converter could be damaged.
iIf at extremely low temperatures no en-
gine oil level is displayed after 5 min-
utes, wait a further 5 minutes before
repeating the engine oil level check.
POK
\1Do not add oil.
-1.0 qt
\1Add the amount of oil
shown (\2page 190).
-1.5 qts-2.0 qtsHI
\1The engine oil level is
too high. Have the oil
siphoned off.
iEngine oil level display:
\4
qt in USA only
\4l in Canada only