2007 Citroen C6 height adjustment

II
1111
A
B
FED
C
21G
IN BRIEF
FRONT SEATS
C. Adjustment of the backrest angle.
D. Adjustment of the backrest lum-bar support.
E. Seat height and slide adjust-ments.
F. Adjustment of the seat cushion angle.
G. Memorisation of dashboard adjustments:
- Driver's seat.
- Steering wheel.
- Exterior rear view mirrors.
- Head-up display.
You have the possibility to mem-orise two driving positionsusing buttons 1 and 2.
ELECTRICAL ADJUST-MENTS
While the vehicle is stationary, unlock the steering wheel by push-ing the lever forward.
Adjust the height and the reach of the steering wheel, then lock the position by pulling the lever upwards.
MANUAL STEERING COL-UMN ADJUSTMENT
A. Adjustment of the backrest angle.
B. Controls for the heated seats.
282927
G E T T I N G S T A R T E D

27
II
S T E E R I N G C O L U M N A D J U S T M E N T –
S E A T B E L T H E I G H T A D J U S T M E N T
ELECTRICAL ADJUSTMENT OF THE STEERING WHEEL FOR HEIGHT OR REACH
While the vehicle is stationary, adjust the height or the reach of the steering wheel by moving the control:forward or rearward to adjust the reachup or down to adjust the height.
The steering wheel adjustment is memorised with the driving posi-tion (See “Memorisation”).

28
II
1
3
2
F R O N T S E A T S
ADJUSTMENT OF THE BACKREST ANGLE
Action the control 1 and adjust the angle of the backrest.
It is possible to tilt the backrest 45° forwards until it locks. To unlock it, press control 1.
ADJUSTMENTS TO THE HEIGHT AND ANGLE OF THE HEAD RESTRAINT
To raise it, pull upwards.
To lower it, press on the control 2 to unlock it, and simultaneously on the head restraint itself.
To adjust the angle of the head restraint, tilt it forwards or rearwards at the bottom.
To raise it, press control 2 to unlock it, then pull it upwards.
CONTROLS FOR THE HEATED SEATS
The front seats can be heated independently of each other . On the con-trols for the heated seats 3 located on the outer side of the seats, rotate the knob to select any of three heat intensities:
0: Off.
1: Slight heat.
2: Medium heat.
3: Maximum heat.
Note: The heated seats only operate when the engine is running.
SEAT HEIGHT AND SLIDE ADJUSTMENTS
See following page.

29
II
A
B
C
D
DCB
A
F R O N T S E A T S
Do not drive the vehicle with the head restraints removed; these must be in place, correctly adjusted.
ELECTRICAL ADJUSTMENTS
Adjustment of the backrest angle
To adjust the angle of the backrest, press button A.
Lumbar adjustment
To adjust the backrest lumbar support, press button B.
Seat height and slide adjustments
To slide the seat, press on the horizontal arrows on control C.
To adjust the seat for height, press on the vertical arrows on control C.
Adjustment of the seat cushion angle
To adjust the seat cushion angle, press on control D.
Note: These adustments remain available for a limited time:After you have opened a doorAfter
After you have switched off the ignitionAfter

55
II2
14
3
H E A D - U P D I S P L A Y
The Head-up display projects essential driving data into the driver's fi eld of vision. This enables the driver never to take his eyes off the road.
ACTIVATION/DEACTIVATION
To activate/deactivate the Head-up display: when you switch on the ignition, press on button 1.
The function status (activated/deac-tivated) when you stop the engine is retained when you restart.
ADJUSTMENTS OF THE HEAD-UP DISPLAY
Height adjustment
To adjust the height for the Head-up display, press on buttons 2 and 3.
It is recommended to adjust it as low as possible.
Brightness adjustment
The Head-up display has a bright-ness sensor so that the information can be seen to the best advantage, whatever the ambient brightness.
You can enhance the display brightness at any time by rotating the control 1.
Note:In certain extreme weather con-ditions (rain and/or snow, strong sunlight), the Head-up display may be momentarily subject to interference.
When emerging from a tunnel, there is a certain delay before the system can re-adapt the display brightness to the out-side conditions.
Remark: Certain types of specta-cles may disperse the light coming from the Head-up display.
There is memorisation of driving positions as well as those for the Head-up dis-play
The adjustments you have made for the Head-up display are adopted alongside the driving posi-tion memorisations (see “Memori-sation”): they are:Height adjustment.
Brightness.The types of information selected.

102
III
G R O U N D C L E A R A N C E A D J U S T M E N T
Position changes may only be made when the engine is running.
The ground clearance is adjusted automatically. You can however modify the vehicle height in certain specifi c cases.
To change the position
Press once on one of the adjust-ment controls. The change of posi-tion is indicated at the start of the adjustment by:A message orA
Temporary display of the initial position with the symbol for the position requested.Note: You are recommended to avoid any changing of position while you have your foot on the brake.
Viewing of the position of the vehicle
On completion of the adjustmentyou see either a message or an illustration of the position attained by the vehicle, with the appropriate symbol.

103
III
G R O U N D C L E A R A N C E A D J U S T M E N T
AUTOMATIC CORRECTION OF GROUND CLEARANCE
Your vehicle has active suspension with variable damping which is electronically controlled. This automatically regu-lates the ground clearance according to the vehicle speed and the road surface conditions.
Limits on access to the posi-tions
Maximum height:
Impossible if speed > 10 km / h (6 mph).
Intermediate position:
Impossible if speed > 40 km / h (24 mph).
Normal road position: Always permitted.
Minimum height:
Impossible if speed > 10 km / h (6 mph).Note: If the speed authorised for a particular position is exceeded, the vehicle reverts automatically to the normal road position.
Signalling of a requested position not authorised
On the display:
The display indicates for a short time, via a message or by hatching on the requested position, that the adjustment is impossible.
The vehicle remains in the position that is authorised and the display confi rms this position.
Automatic variation of ground clearanceIf the speed Ifexceeds110 km / h(68 mph), on a good road, the ground clearance is lowered.
The vehicle reverts to the normal road position if the road dete-riorates or if the speed comes below 90 km / h (56 mph).When the vehicle is stationary the ground clearance is low-ered to the parking position.

157
VI
4
Before positioning the jack, always adjust the vehicle's ground clearance to the “maximum height” position and retain this adjustment for as long as the jack is under the veh icle (do not use the hydraulic adjustments).
Never get underneath the vehicle if it is supported only by the jack.
The jack and all the tools are designed specifi cally for use on your particular vehicle. Do not use them for any other applications.
Have the original wheel repaired and refitted as so on as possible.
It is essential not to exceed a speed of 80 km/h (50 mph) on your spare wheel.
REMOVAL1. Park the vehicle on stable, fi rm ground that is not slippery. Apply the parking brake.2. With the engine idling, adjust the ground clearance to maximum height. See “Comfort” and “Adjusting the ground clearance”. Switch off the igni-tion and engage fi rst gear or reverse gear depending on any slope (for a vehicle with automatic gearbox, select position P).3. Position the chock at the wheel that is diametrically opposite the one to be replaced.4. Position the jack at one of the four jacking-points provided on the sub-frame close to the wheels, then use the handle to unwind the jack until it reaches the ground.5. Slide the removal tool 4 into the notch and lever vigorously to detach the anti-theft bolt protector. See illustration. You can use the handle at the extremity of the tool 4.6. Slacken the wheel bolts.7. Continue to extend the jack until the wheel is a few cen timetres off the ground.8. Undo the bolts, remove the wheel.
C H A N G I N G A W H E E L