2007 Citroen C6 DAG wheel
[x] Cancel search: wheelPage 147 of 216
150
VI
A
B
Use a tool to detach the bulb-hold-ers and change the bulbs.Note: The tool for undoing the screws is to be found in the toolbox i n t h e s p a r e w h e e l . S e e “ C h a n g i n g a wheel”.
REAR CENTRAL LENSA Reversing lampB Foglamp
The bulbs for lamps A and B have a common bulb-holder. Contact a CITROËN dealer.
THIRD STOPLAMP
Contact a CITROËN dealer.
To gain access to the bulb-hold-ers, open the boot and undo the four screws on the bodywork. Then lower the boot lid in order to be able to pull out the two rear lamp units, without pulling on the electric cables.
NUMBER PLATE
Detach the transparent shield, then pull out the bulb. Bulb: W 5 W.
After each operation, check that the lamps work.
C H A N G I N G B U L B S
Page 150 of 216
153
VI
A
S A F E T Y R E C O M M E N D A T I O N S
It is recommended that you have your towbar installed and r e m o v e d b y a C I T R O Ë N d e a l e r .It is recommended that you have recommended that
If you are towing another vehicle, the latter must be free-wheeling (gearbox in neutral).
Dimensions ( i n m e t r e s ):
A: 0.971
TOWBAR
( B o a t , c a r a v a n , e t c . )
It is recommended that you have your towbar installed and r e m o v e d b y a C I T R O Ë N d e a l e r .have your towbar installed and towbar installed
If you are climbing a steep gradient and the engine gets excessively hot, certain functions become una-vailable (e.g. sequential control of the automatic gearbox, the air con- d i t i o n i n g ) .
If you are towing, it is necesaary to deactivate the parking assist-ance by pressing the control on the dashboard. See “Parking assist-ance”.
It is recommended that you remove the towing ball, so that it does not interfere with the functioning of the proximity sensors, when you are not using a trailer.
MAINTENANCE
if cleaning the vehicle with a high pressure systemYour P i l o t e d D e fl e c t o r h a s t o b e ourclosed.
It is not advisable to clean the underside of the vehicle, for fear of damaging the electric parking brake.As water may penetrate into the vehicle interior via the door apertures, do not target these areas.
Page 153 of 216
156
VI
4
3
8
9
61
2
5
7
C H A N G I N G A W H E E L
ACCESS TO THE SPARE WHEEL
To access the spare wheel1. L i f t t h e b o o t fl o o r b y m e a n s o f t h e s t r a p .2. Anchor the strap on the roof of the boot.3. To remove the spare wheel, detach the belt then push the wheel for-wards so as to be able to lift it.
TO REPOSITION THE SPARE WHEEL
To put the spare wheel back in the boot1. P o s i t i o n t h e s p a r e w h e e l fl a t i n t h e b o o t , t h e n p u l l i t t o w a r d s y o u .2. Next place the toolbox inside the wheel, then secure the a ssembly with the belt.3. R e l e a s e t h e s t r a p t o r e t u r n t h e b o o t fl o o r t o i t s i n i t i a l p o s i t i o n .
Tyre pressures
Tyre pressures are indicated on the label which is positioned l ow down on t h e f r o n t p i l l a r . S e e “ V e h i c l e i d e n t i fi c a t i o n ” a n d “ U s e r P r e c a u t i o n s ” . ( O n t h i s label you will see a pressure for normal speeds and a pressure for high s p e e d s ) .
1. Handle2. Jack3. T o o l f o r r e m o v i n g / r e fi t t i n g t h e wheel bolts4. Tool for removing the anti-theft bolt protector5. Centring guide6. Tool for removing foglamps and reversing lamps7. Handle extension8. Towing eye9. Movable chock
TOOLS
The tools are to be found in a pro-tective holder inside the spare wheel. Pull back the retaining strap to have access.
Page 154 of 216
157
VI
4
Before positioning the jack, always adjust the vehicle's ground clearance to the “maximum height” position and reta in this adjustment for as long as the jack is under the vehicle (do not use the hydraulic adjustments).
Never get underneath the vehicle if it is supported only by the jack.
T h e j a c k a n d a l l t h e t o o l s a r e d e s i g n e d s p e c i fi c a l l y f o r u s e o n y o u r particular vehicle. Do not use them for any other a pplications.
Have the original wheel repaired and refitted as so on as possible.
It is imperative not to exceed a speed of 80 km / h (50 mph) on the spare wheel.
REMOVAL1. P a r k t h e v e h i c l e o n s t a b l e , fi r m g r o u n d t h a t i s n o t s l i p p e r y . A p p l y t h e parking brake.2. With the engine idling, adjust the ground clearance to maximum height. See “Comfort” and “Adjusting the ground clearance”. Switch off the igni- t i o n a n d e n g a g e fi r s t g e a r o r r e v e r s e g e a r d e p e n d i n g o n a n y s l o p e ( f o r a v e h i c l e w i t h a u t o m a t i c g e a r b o x , s e l e c t p o s i t i o n P ) .3. Position the chock at the wheel that is diametrically opposite the one to be replaced.4. Position the jack at one of the four jacking-points provided on the sub-frame close to the wheels, then use the handle to unwind the jack until it reaches the ground.5. Slide the removal tool 4 into the notch and lever vigorously to detach the anti-theft bolt protector. See illustration. You can use the handle at the extremity of the tool 4.6. Slacken the wheel bolts.7. Continue to extend the jack until the wheel is a few cen timetres off the ground.8. Undo the bolts, remove the wheel.
C H A N G I N G A W H E E L
Page 155 of 216
158
VI
It is imperative not to exceed a speed of 80 km / h (50 mph) on the spare wheel.
T h e w h e e l b o l t s a r e s p e c i fi c t o t h e t y p e o f w h e e l .
I f t h e t y p e o f w h e e l i s c h a n g e d , c h e c k w i t h y o u r C I T R O Ë N d e a l e r that the wheel bolts are compatible with the new wheels.
Note: take care to note down the code number engrav ed on the head of the anti-theft bolt socket. This will enable you to obtain replacement anti-theft bolt sockets from a dealership.
WHEEL FOR TEMPORARY USE
If your vehicle is equipped with a spare wheel for temporary use o n l y , w h e n fi t t i n g i t i t i s n o r m a l t o observe that the wheel bolts do not come to bear on the wheel rim.
The spare wheel is secured by the conical tapering of the wheel bolt’s shaft. See illustration.
W h e n r e fi t t i n g t h e o r i g i n a l w h e e l , ensure that the wheel bolt contact surfaces are clean and in good condition.
REFITTING A WHEEL1. Fit the wheel on the hub, using the centring guide. Make sure that the contact surface between the hub and the wheel is clean.2. Screw in the bolts but do not fully tighten them.3. Lower the jack and remove it.4. Tighten the wheel bolts, using the wheelbrace.5. R e fi t t h e e m b e l l i s h e r .6. Return the ground clearance to the normal position. See “Adjusting ground clearance”.7. Ensure the tyre pressure is c o r r e c t ( s e e “ V e h i c l e i d e n t i fi c a - t i o n ” ) a n d h a v e t h e b a l a n c i n g checked.
WHEEL EQUIPPED WITH DEFLATION DETECTION SENSOR
Such wheels have tyre pressure sensors. It is essential to have repairs carried out by a CITROËN dealer.
ANTI-THEFT BOLTS
Each wheel is equipped with one anti-theft bolt.
To remove it1. Remove the protector that is covering it by means of the tool 4 for “removing anti-theft protectors”.2. Use the anti-theft socket with the handle.
C H A N G I N G A W H E E L
Page 156 of 216
159
VI
T O W I N G – L I F T I N G
TOWING WITH WHEELS ON THE GROUND
Towing eyes can be used at the front and at the rear of the vehicle.
Detach the cover:For the front cover, lever with a screwdriver at the top of the co ver.For
For the rear cover, press on the right hand side.For
The ignition key must be in position M to retain steering.
Use a bar with attachments to the towing eyes as above.
The towing eye is removable, to be stowed in the jack protect ion box inside the spare wheel.
Page 171 of 216
111111
Ij
e
abc
fgh
d
i
N A V I G A T I O N / G U I D A N C E
Head-up Display (according to model) T h i s f a c i l i t y p r o j e c t s i n t h e d r i v e r ' s fi e l d o f vision all the important types of information, notably the navigation instructions j.when navigation is in operation, direction a r r o w s w i l l fl a s h .See vehicle handbook.
The Multifunction screenDuring a guidance, you have access to the following types of information:
a Manœuvre to be made, or direction to be taken.b Distance to the next manoeuvre.c Next manoeuvre to be made.d N ex t r o a d t o b e t a ke n a n d n a m e o f town.e S y m b o l c o n c e r n i n g T r a f fi c i n f o r m a t i o n o r the services that are in proximity.f Road you are currently on, name of the town.g Estimated time of arrival at destination ( b a s e d o n fl o w i n g t r a f fi c ) .h D i s t a n c e t o fi n a l d e s t i n a t i o n .i Altitude.
Apart from on the screen, the manœuvres t o b e m a d e a r e a n n o u n c e d by a vo i c e synthesiser.
Repeating the last piece of voice infor-mationA few seconds after enunciation of a guid-ance voice instruction, you have the pos-sibility of hearing it again.Keep the end of the lighting control stalk pressed.
How to adjust the volume for the voice instructions ?During enunciation of a voice instruction, press on the volume adjustment but tons either on the control panel or at the steer-ing wheel. A d j u s t m e n t i s a l s o p o s s i b l e i n t h e “ C o n fi g u -ration” menu.
DESCRIPTION OF THE TYPES OF INFORMATION DISPLAYED DURING NAVIGATIONTHE VOICE SYNTHESIS
Depending on the situation of the vehicle and the reception of the GPS information, this information may temporarily be absent from the screen.
Page 187 of 216
272727
IVAB
C
D
S e l e c t i o n o f a p r e - d e fi n e d m u s i c a l a m b i a n c e a u t o m a t i c a l l y a d j u s t s b a s s a n d t r e b l e . S e l e c t t h e m u s i c a l a m b i a n c e “ N o n e ” t o personalise your adjustment of bass and treble. A d j u s t m e n t s o f l o u d n e s s , b a s s a n d t r e b l e ( w h e n t h e y a r e a v a i l a b l e ) a r e s p e c i fi c t o e a c h s o u r c e .The sound volume is automatically corrected as a function of vehicle speed, provided the facility has been activated.
Press on the SOURCE button or on the con-trol at the steering wheel (A) to choose radio source, CD source or Jukebox source
or
Rotate the control or use the buttons at the steering (B) and (C) to increase or decrease the volume.
How to stop the sound momentarily ?Press on the controls at the steering wheel (B) and (C) simultaneously.The sound of the Audio source currently being listened to is cut. The guidance instruc-tions remain activated. To restore sound, press on any of the NaviDrive buttons or on one of the controls at the steering wheel.
or
Press on button (D) to select: t h e p r e - d e fi n e d m u s i c a l a m b i a n c e s ,bass,treble,loudness,front /rear and left /right balanceautomatic correction of the volume as a function of vehicle speed.Rotate the control to modify the value of the parameter displayed.The value is automatically taken into account without the need for validation.