Page 149 of 216
152
VI
B
C
D
A
C H A N G I N G B U L B S
2. Use a tool to detach the two lugs holding the lens.
3. Without touching the seal, dis-engage the lamp unit upwards and orient it so that the bulbs are pointing outwards.
5. R e p o s i t i o n t h e l e n s , fi r s t i n s e r t -ing the pin furthest forward, then push.Make sure that the rear screen seals and the lamp units are correctly located.
6. Secure the two lugs.
4. Replace bulbs that are faulty.
Page 151 of 216
154
VI
R O O F B A R S
Do not exceed the maximum permitted load.
For the maximum distributed load on the roof bars: see the chapter “General”.
Recommendations:Spread the load evenly, avoiding overloading on one side.
Position the heaviest weight as low down as pos-sible.Tie the load down securely and add warning signs if it is protruding.
Drive conservatively, as the vehicle will be more vul-nerable to side winds.
The stability of your vehicle may be altered.Remove the roof rack or roof bars when you are not using them.
Page 153 of 216
156
VI
4
3
8
9
61
2
5
7
C H A N G I N G A W H E E L
ACCESS TO THE SPARE WHEEL
To access the spare wheel1. L i f t t h e b o o t fl o o r b y m e a n s o f t h e s t r a p .2. Anchor the strap on the roof of the boot.3. To remove the spare wheel, detach the belt then push the wheel for-wards so as to be able to lift it.
TO REPOSITION THE SPARE WHEEL
To put the spare wheel back in the boot1. P o s i t i o n t h e s p a r e w h e e l fl a t i n t h e b o o t , t h e n p u l l i t t o w a r d s y o u .2. Next place the toolbox inside the wheel, then secure the a ssembly with the belt.3. R e l e a s e t h e s t r a p t o r e t u r n t h e b o o t fl o o r t o i t s i n i t i a l p o s i t i o n .
Tyre pressures
Tyre pressures are indicated on the label which is positioned l ow down on t h e f r o n t p i l l a r . S e e “ V e h i c l e i d e n t i fi c a t i o n ” a n d “ U s e r P r e c a u t i o n s ” . ( O n t h i s label you will see a pressure for normal speeds and a pressure for high s p e e d s ) .
1. Handle2. Jack3. T o o l f o r r e m o v i n g / r e fi t t i n g t h e wheel bolts4. Tool for removing the anti-theft bolt protector5. Centring guide6. Tool for removing foglamps and reversing lamps7. Handle extension8. Towing eye9. Movable chock
TOOLS
The tools are to be found in a pro-tective holder inside the spare wheel. Pull back the retaining strap to have access.
Page 155 of 216
158
VI
It is imperative not to exceed a speed of 80 km / h (50 mph) on the spare wheel.
T h e w h e e l b o l t s a r e s p e c i fi c t o t h e t y p e o f w h e e l .
I f t h e t y p e o f w h e e l i s c h a n g e d , c h e c k w i t h y o u r C I T R O Ë N d e a l e r that the wheel bolts are compatible with the new wheels.
Note: take care to note down the code number engrav ed on the head of the anti-theft bolt socket. This will enable you to obtain replacement anti-theft bolt sockets from a dealership.
WHEEL FOR TEMPORARY USE
If your vehicle is equipped with a spare wheel for temporary use o n l y , w h e n fi t t i n g i t i t i s n o r m a l t o observe that the wheel bolts do not come to bear on the wheel rim.
The spare wheel is secured by the conical tapering of the wheel bolt’s shaft. See illustration.
W h e n r e fi t t i n g t h e o r i g i n a l w h e e l , ensure that the wheel bolt contact surfaces are clean and in good condition.
REFITTING A WHEEL1. Fit the wheel on the hub, using the centring guide. Make sure that the contact surface between the hub and the wheel is clean.2. Screw in the bolts but do not fully tighten them.3. Lower the jack and remove it.4. Tighten the wheel bolts, using the wheelbrace.5. R e fi t t h e e m b e l l i s h e r .6. Return the ground clearance to the normal position. See “Adjusting ground clearance”.7. Ensure the tyre pressure is c o r r e c t ( s e e “ V e h i c l e i d e n t i fi c a - t i o n ” ) a n d h a v e t h e b a l a n c i n g checked.
WHEEL EQUIPPED WITH DEFLATION DETECTION SENSOR
Such wheels have tyre pressure sensors. It is essential to have repairs carried out by a CITROËN dealer.
ANTI-THEFT BOLTS
Each wheel is equipped with one anti-theft bolt.
To remove it1. Remove the protector that is covering it by means of the tool 4 for “removing anti-theft protectors”.2. Use the anti-theft socket with the handle.
C H A N G I N G A W H E E L
Page 184 of 216
242424
IIICity hall, City centre
Hospital
PUBLIC AUTHORITIES AND SECURITY
Universities, Colleges, Schools
H OTELS , RESTAURANTS , BUSINESS AND RETAIL PARKS
Hotels
Vineyards
Restaurants
Business centre
Supermakets, Shopping malls
S PORTS AND OPEN AIR CENTRES
Sports centres and complexes
Golf courses
Parks, gardens
Winter sports
Public attractions
C ULTURE , TOURISM , ENTERTAINMENT
Culture, museums and theatres
Tourism, historic monuments
Shows, exhibitions
Cinemas
Skating, Bowling
TRANSPORT AND MOTORING
A i r p o r t s , fl y i n g c l u b s
Rail stations, bus stations
Car hire
Car parks, rest areas
Ferry terminals, port areas
Service stations, garages
Radar zones/High-accident zones (depending on the cou ntry of marketing and availability of the service)
CITROËN Dealer or Repairer
Casinos and night life
M A P
C E N T R E S O F I N T E R E S T
