Item Number Item Remarks
4 Pivot Points and Hinges Apply chassis lubricant.
5 Pivot Points and Hinges Apply chassis lubricant.
6 Slack Adjuster** One fitting.
7Brake Cam Roller Pins at interface of pin
and shoe**Apply engine oil.
8 Front Steering KnucklesOne fitting each side, lower bushing.
(Hand-operated grease gun only.) Hand-pack
upper bearing.
9 Front Wheel Bearings Hand-pack or lubricate.
10 Steering Tie Rod Ends One fitting each end.
11 Spring Slip Pads* (Multi-Leaf Only) Apply chassis lubricant.
12 Clutch Release Bearing* Cup or fitting.
13 Battery Terminal (except “ST” type) Keep coated with petroleum jelly.
14 Transmission Fill to level of filler plug.
15 Propshaft U-JointsLubricate with GM Part No. 1051344 Wheel
Bearing Lubricant.
16 Parking Brake Clevis Pin$ Apply chassis lubricant.
17 Parking Brake Lever Pivot*, $ Apply chassis lubricant.
18Clutch Release Cross Shaft, Master
Cylinder$Apply chassis lubricant, fill to 1/4 inch (6 mm)
below opening.
19 Release Bearing, Clutch Cross Shaft Two fittings, apply chassis lubricant.
20 Clutch Release Fork Two fittings.
* Applies to some vehicles.
** Applies to air brakes only.
$ Applies to hydraulic brakes only.
303
(2)= An Emission Control Service.
(3)= A Noise Emission Control Device.
(4)= Applies to vehicles sold in the United States
and is recommended for vehicles sold in Canada.
(5)= Check fluid level in brake master cylinder,
power steering pump, front and rear axles,
transmission, and hydraulic spring parking brake
pump (if equipped). A low fluid level in the
brake master cylinder can indicate worn brake
linings and should be checked accordingly.
(6)= Inspect brake lines and hoses for proper
hook-up, binding, leaks, cracks, chafing, etc.
Inspect disc brake pads for wear and rotors for
surface condition. Inspect caliper assemblies.
Check brake pedal for excessive free play or
travel (or every 6 months, whichever occurs first)
and have serviced if needed. Check brakes
more often if driving habits and conditions result
in frequent braking.(7)= This vehicle has the Engine Oil Life System.
This system will show you when to change the
engine oil and filter — usually between 3,000 miles
(5 000 km) and 12,000 miles (20 000 km) since
your last oil change. Under severe conditions,
the indicator may come on before 3,000 miles
(5 000 km). Never drive your 7.8L diesel engine
vehicle more than 12,000 miles (20 000 km),
or 12 months, or 600 engine hours, without an
oil and filter change.
Remember to reset the Engine Oil Life System
whenever the oil is changed. For more information,
seeEngine Oil Life System (Gasoline Engine)
on page 276orEngine Oil Life System
(DURAMAX
®Diesel) on page 278orEngine
Oil Life System (Caterpillar®Diesel Engine)
on page 279.
384
(11)= Chassis Lubrication Service: Lubricate all
grease fittings in front suspension, front axle,
and steering linkage. DO NOT lubricate kingpin
bushings with air pressure equipment; instead,
use a hand grease gun to ensure complete purge
and eliminate sealer cap distortion. Front axle
tie rod ends, both upper and lower kingpin fittings,
and both steering linkage relay rod ends should
be greased with the vehicle loaded on the ground
and wheels turned straight ahead, NOT with
the vehicle on a hoist. Apply kingpin bushing
lubricant to both upper and lower kingpin grease
fittings until new lubricant purges from between
the upper shim pack and thrust bearing. Lubricate
transmission and shift linkage, hood latches
and hood hinges, parking brake lever pivot, clevis
pins and linkage, disc brake caliper rails, clutch
linkage and release bearing (if equipped), bearing
pads, propshaft universal joints, brake camshaft
bracket, slack adjusters, pedal shaft, clutch
cross shaft, clutch pedal springs, and clutch cable
bushing at transmission. Lubricate suspension,
axle, and steering linkage more often when
operating under dusty or muddy conditions and in
excessive off-road use. Frequently power-washed
vehicles will require more frequent lubrication.(12)= Check steering system:
•Look for damaged, loose, or missing parts.
Inspect the steering linkage relay rod and
tie rod ends for looseness or lack of lubricant.
Also look for parts showing signs of wear
or lack of lubrication. Replace parts as
needed. Also check steering gear mounting
bolts, pitman arm nut, gear housing upper
cover and side cover attaching bolts, steering
column mounting bolts and cardan joint
clamp bolts; tighten if necessary. See the
service manual.
•Inspect power steering hoses, tubes, and
fittings for leaks. Hoses and lines must not
be twisted, kinked, or tightly bent. Make sure
clips, clamps, supporting tubes, and hoses
are in place and properly secured.
•Check steering gear for leakage around
pitman shaft and housing. If leakage is evident
(lubricant oozing out, not just oily film), leak
should be corrected immediately.
386