2007 CHEVROLET KODIAK ignition

Hill and Mountain Roads
Driving on steep hills or mountains is different from
driving in flat or rolling terrain.
Here are some tips that can make your drive
through steep country safer:
•Keep the vehicle in good shape. Check all fluid
levels and also the brakes, tires, cooling
system, and transmission. These parts can
work hard on mountain roads.
{CAUTION:
If you do not shift down, your brakes
could get so hot that they would not work
well. You would then have poor braking or
even none going down a hill. You could
crash. Shift down to let your engine assist
your brakes on a steep downhill slope.
{CAUTION:
Coasting downhill in NEUTRAL (N) or with
the ignition off is dangerous. Your brakes
will have to do all the work of slowing
down. They could get so hot that they
would not work well. You would then have
poor braking or even none going down a
hill. You could crash. Always have your
engine running and your vehicle in gear
when you go downhill.
230

Running Out of Fuel
If the diesel engine stalls and you think that you
have run out of fuel, do this to restart your engine:
{CAUTION:
Diesel fuel is ammable. It could start a
re if it gets on hot engine parts. You
could be burned. Do not let too much fuel
ow from the air bleed valve, and wipe up
any spilled fuel with a cloth.
1. If you are parked on a level surface, add at
least 2 gallons (7.6 liters) of fuel. However, if
you are parked on a slope, you may need
to add up to 5 gallons (18.9 liters) of fuel.
2. Follow the fuel priming procedure earlier in
this section to prime the fuel filter.3. Close the air bleed valve.
4. Turn the ignition key to START for 10 to
15 seconds at a time until your engine
starts. If the engine tries to run, but does not
run smoothly, increase the rpm a little
using the accelerator pedal. This will help
force air through the system.
Your check engine light may come on if the
vehicle has run out of fuel. This light may stay on
for a few drive cycles after the condition is
corrected, but will eventually clear itself.
262

Fuel Filter Replacement
If you want to change the diesel engine fuel filter
yourself, here is how to do it:
{CAUTION:
Diesel fuel is ammable. It could start a
re if something ignites it, and you could
be burned. Do not let it get on hot engine
parts, and keep matches or other ignition
sources away.
First, drain any water from the filter by following
the water draining procedure earlier in this section.
Your vehicle’s engine should be off until the end
of this procedure.
If your vehicle has the 6.6L engine, the fuel filter is
located in the engine compartment on the
driver’s side of the vehicle. If your vehicle has
either the 7.2L or 7.8L engine, the fuel filters are
located in the engine compartment on the
driver’s side of the vehicle, and on the driver’s
side frame rail in front of the fuel tank.
1. Apply the parking brake.2. Unplug the water
sensor wire
connected to the fuel
filter and unscrew
the filter element.
3. Remove the filter element. If there is any dirt
on the filter sealing surface, clean it off.
Remove and reuse the water sensor float
switch located on the bottom of the fuel filter.
4. Install the new filter element.
5. Reinstall and tighten the filter container and
reconnect the water sensor wire to the filter.
6. Use the fuel filter priming procedure earlier in
this section to prime the fuel filter.
7. Tighten the air bleed valve by turning it
clockwise until hand-tight.
8. Start your engine and let it idle for
five minutes. Check your fuel filter and air
bleed valve for leaks.
263

If the system is ever reset accidentally, you must
change your oil at 3,000 miles (5 000 km)
since your last oil change. Remember to reset the
oil life system whenever the oil is changed.
How to Reset the Engine Oil Life
System
The Engine Oil Life System calculates when to
change your engine oil and filter based on vehicle
use. Anytime your oil is changed, reset the
system so it can calculate when the next oil
change is required. If a situation occurs where you
change your oil prior to a change engine oil light
being turned on, reset the system.
To reset the change engine oil light, do the
following:
1. Turn the ignition key to RUN with the
engine off.
2. Fully press and release the accelerator pedal
slowly three times within 10 seconds.
If the change engine oil light flashes for
five seconds, the system is resetting.
3. Turn the key to OFF.
If the change engine oil light comes back on when
you start your vehicle, the engine oil life system
has not reset. Repeat the procedure.
What to Do with Used Oil
Used engine oil contains certain elements that may
be unhealthy for your skin and could even cause
cancer. Do not let used oil stay on your skin for very
long. Clean your skin and nails with soap and
water, or a good hand cleaner. Wash or properly
dispose of clothing or rags containing used engine
oil. See the manufacturer’s warnings about the use
and disposal of oil products.
Used oil can be a threat to the environment. If you
change your own oil, be sure to drain all the oil from
the filter before disposal. Never dispose of oil by
putting it in the trash, pouring it on the ground, into
sewers, or into streams or bodies of water. Instead,
recycle it by taking it to a place that collects used
oil. If you have a problem properly disposing of your
used oil, ask your dealer, a service station or a local
recycling center for help.
277

To reset the Engine Oil Life System, do the
following:
1. Turn the ignition key to RUN with the
engine off.
2. Fully press and release the accelerator pedal
slowly three times within 10 seconds.
If the change engine oil light flashes for
five seconds, the system is resetting.
3. Turn the key to OFF.
If the change engine oil light comes back on when
you start your vehicle, the Engine Oil Life
System has not reset. Repeat the procedure.
What to Do with Used Oil
Used engine oil contains certain elements that may
be unhealthy for your skin and could even cause
cancer. Do not let used oil stay on your skin for very
long. Clean your skin and nails with soap and
water, or a good hand cleaner. Wash or properly
dispose of clothing or rags containing used engine
oil. See the manufacturer’s warnings about the use
and disposal of oil products.Used oil can be a threat to the environment. If you
change your own oil, be sure to drain all the oil
from the filter before disposal. Never dispose of oil
by putting it in the trash, pouring it on the
ground, into sewers, or into streams or bodies of
water. Instead, recycle it by taking it to a place
that collects used oil. If you have a problem
properly disposing of your used oil, ask your
dealer, a service station, or a local recycling
center for help.
Engine Oil Life System
(Caterpillar
®Diesel Engine)
How to Reset the Engine Oil Life
System
The Engine Oil Life System calculates when to
change your engine oil and filter based on vehicle
use. Anytime your oil is changed, reset the
system so it can calculate when the next oil
change is required. If a situation occurs where you
change your oil prior to a change engine oil light
being turned on, reset the system.
279

To reset the Engine Oil Life System, do the
following:
1. Turn the ignition key to RUN with the
engine off.
2. Fully apply and hold the brake pedal while
you fully press and release the accelerator
pedal, pausing slightly at each press and each
release, three times within five seconds.
3. Turn the key to OFF.
If the change engine oil light comes back on when
you start your vehicle, the Engine Oil Life
System has not reset. Repeat the procedure.
Engine Air Cleaner/Filter
The engine air
cleaner/filter is located
in the center of the
engine compartment.
When to Inspect the Engine Air
Cleaner/Filter
If your vehicle has an
air cleaner/filter change
indicator, inspect the
indicator at every
oil change and replace
the filter when the
indicator tells you to.
For vehicles without a change indicator, inspect
the air cleaner/filter at every oil change and
replace the filter at the first oil change after
25,000 miles (40 000 km).
How to Inspect the Engine Air
Cleaner/Filter
Locate the filter change indicator. When the
change indicator turns black or is in the red/orange
change area, replace the filter and reset the
indicator.
280

Brakes
Brake Fluid
If your vehicle has
hydraulic brakes, there
is a brake master
cylinder in the engine
compartment on the
driver side of the vehicle.
Refer to the
Maintenance Schedule
to determine when to
check the brake fluid.
{CAUTION:
Do not add brake uid before you check
the level. If you do, you could get too
much brake uid. Brake uid could spill
on the hot engine and it can catch re.
You could be burned and your vehicle
could be damaged. See “Checking Brake
Fluid” in this section.
Checking Brake Fluid
Apply the brake pedal several times with the
ignition off. The brake fluid reservoir is in
the engine compartment on the driver side of the
vehicle. Clean one of the reservoir caps and
the area around the cap, and remove it.
The fluid level should be
even with the bottom
ring of the filler opening.
If it is low, add enough
fluid to fill the reservoir to
the proper level.
297

Notice:Ignoring these steps could result in
costly damage to your vehicle that would
not be covered by your warranty.
Trying to start your vehicle by pushing or
pulling it will not work, and it could damage
your vehicle.
1. Check the other vehicle. It must have a
12-volt battery (or batteries) with a negative
ground system.
Notice:If the other vehicle’s system is not a
12-volt system with a negative ground,
both vehicles can be damaged. Only use
vehicles with 12-volt systems with negative
grounds to jump start your vehicle.
If you have a diesel engine vehicle with
two batteries (or more), you should know
before you begin that, especially in cold
weather, you may not be able to get enough
power from a single battery in another
vehicle to start your diesel engine.
If your vehicle has more than one battery, use
the one closest to the starter — this will
reduce electrical resistance.2. Get the vehicles close enough so the jumper
cables can reach, but be sure the vehicles are
not touching each other. If they are, it could
cause a ground connection you do not
want. You would not be able to start your
vehicle, and the bad grounding could damage
the electrical systems.
To avoid the possibility of the vehicles rolling,
set the parking brake firmly on both vehicles
involved in the jump start procedure. Put
an automatic transmission in PARK (P) or a
manual transmission in NEUTRAL before
setting the parking brake. If you have a
four-wheel-drive vehicle, be sure the transfer
case is in a drive gear, not in NEUTRAL.
Notice:If you leave your radio or other
accessories on during the jump starting
procedure, they could be damaged. The repairs
would not be covered by your warranty.
Always turn off your radio and other
accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the
cigarette lighter or accessory power outlets.
306