❑Cooling system service. Clean the cooling
system filler cap with clean water, clean
the core, pressure test the cap and the
system for proper pressure capability, and
inspect condition of cooling and heater
hoses and clamps. Replace hoses if cracked,
swollen, or damaged.
❑Replace fuel filter(s) (or every 12 months,
whichever occurs first).(2)
❑Steering system service.(12)
❑Front and rear suspension service.(13)
❑Spring-to-axle U-bolts and shackle bolts
service.(15)
❑Exhaust system service (or every 6 months,
whichever occurs first).(2) (3) (16)
❑Inspect door hinge pins and bushings and
replace as necessary.
❑Wheel bearing (grease type) service (and
whenever hubs are removed).(22) (36)
❑Wheels and tires service.(14)
❑Hydraulic brake service (or every 6 months,
whichever occurs first).(6) (36)
❑Parking brake service (or every 6 months,
whichever occurs first).(21)❑Air brake service (or every 6 months, whichever
occurs first).(32)
❑Air brake automatic slack adjuster service (or
every 500 hours, whichever occurs first).(33)
❑Check air brake relay valve operation and check
for leaks (or every month, or every 300 hours,
whichever occurs first).
❑Clean air brake application valve (or every
3 months, or every 300 hours, whichever
occurs first). Lubricate linkage.
❑Air brake chamber service (or every 2 months,
whichever occurs first).(34)
❑Air brake system valve service (or every
3 months, or every 900 hours, whichever
occurs first).(37)
❑C600, C700, and C800 Gasoline Engines
Only: Engine drive belts service (or every
12 months, whichever occurs first).(17)
❑Thermostatically controlled engine cooling
fan service.(3) (19)
❑Shields and underhood insulation
service.(3) (4) (20)
❑Rear axle air shift motor service.(10)
380
(22)= Wheel bearing service:
•Grease type — Clean, inspect, and lubricate
with the proper wheel bearing grease at
designated intervals or when hubs are
removed. SeePart C: Recommended Fluids
and Lubricants on page 397.
•Oil-filled type — Some wheel bearings are
lubricated by axle lubricant. When you
have oil-filled hubs, use lubricant identical
to that used in the axle. Lubricant change
intervals are the same for front and rear
axles. However, you must maintain the proper
oil level between change intervals. See
Front Wheel Bearings with Oil-Filled Hubs
on page 319andPart C: Recommended
Fluids and Lubricants on page 397.
(23)= Check the air intake system installation
to see that gaskets are seated properly and
all hose connections, fasteners, and other
components are tight. Tighten connections
and fasteners or replace parts as required.(24)= Evaporative Control System Service,
if equipped: Check all fuel and vapor lines and
hoses for proper connections and correct routing
(or every 24 months, whichever occurs first).
Replace parts as needed.
(25)= Replace spark plugs. Inspect wires for
damage. Check the wire boot and boot heat
shield fit at spark plugs and coil. Replace parts
as needed.
(26)= Check the fuel tank, fuel cap and fuel lines
for damage which could cause leakage. Inspect
fuel cap for correct sealing ability and any
indications of damage. Check fuel cap gasket
for even filler neck imprint. Replace parts as
needed.
(27)= Check Exhaust Gas Recirculation (EGR)
system as described in the service manual.
SeeService Publications Ordering Information
on page 415.
388
