2007 CHEVROLET KODIAK lock

Priming the 7.8L Isuzu 6H Diesel Engine
If your vehicle is equipped with the 7.8L Isuzu 6H
diesel engine, use the following procedure to
prime the engine:
1. Make sure there is fuel in the fuel tank.
2. Make sure the specified fuel filter is properly
installed.
3. Make sure the fuel lines are securely
connected.
4. Make sure the fuel filter is cool to the touch.
5. Use a clean cloth to remove dirt and oil
from the fuel filter head and breather valve.6. Use the palm of your hand to repeatedly
press and release the plunger (1) at the
top of the fuel filter priming pump. Continue
until the plunger resistance becomes firm. This
may take from 20 to 100 times, depending
upon fuel tank location.
7. Turn the fuel filter breather valve screw (2)
counterclockwise several turns to open the
breather valve.
8. Use the palm of your hand to repeatedly
press and release the plunger (1) at the
top of the fuel filter priming pump until fuel
begins to seep from the breather valve.
9. Tighten the fuel filter breather screw (2) to the
specified torque, 4.9
Y(43 in. lbs).
10. Use the palm of your hand to press and
release the plunger (1) at the top of the
fuel filter priming pump about 20 more times.
This sends fuel to the engine.
11. Use a clean cloth to remove any fuel from the
fuel filter and surrounding area.
12. Start the engine and allow it to idle for a
few minutes.
13. Check the fuel filter for leakage.
261

Fuel Filter Replacement
If you want to change the diesel engine fuel filter
yourself, here is how to do it:
{CAUTION:
Diesel fuel is ammable. It could start a
re if something ignites it, and you could
be burned. Do not let it get on hot engine
parts, and keep matches or other ignition
sources away.
First, drain any water from the filter by following
the water draining procedure earlier in this section.
Your vehicle’s engine should be off until the end
of this procedure.
If your vehicle has the 6.6L engine, the fuel filter is
located in the engine compartment on the
driver’s side of the vehicle. If your vehicle has
either the 7.2L or 7.8L engine, the fuel filters are
located in the engine compartment on the
driver’s side of the vehicle, and on the driver’s
side frame rail in front of the fuel tank.
1. Apply the parking brake.2. Unplug the water
sensor wire
connected to the fuel
filter and unscrew
the filter element.
3. Remove the filter element. If there is any dirt
on the filter sealing surface, clean it off.
Remove and reuse the water sensor float
switch located on the bottom of the fuel filter.
4. Install the new filter element.
5. Reinstall and tighten the filter container and
reconnect the water sensor wire to the filter.
6. Use the fuel filter priming procedure earlier in
this section to prime the fuel filter.
7. Tighten the air bleed valve by turning it
clockwise until hand-tight.
8. Start your engine and let it idle for
five minutes. Check your fuel filter and air
bleed valve for leaks.
263

Fuels in Foreign Countries
If you plan on driving in another country outside the
United States or Canada, the proper fuel may be
hard to find. Never use leaded gasoline or any other
fuel not recommended in the previous text on fuel.
Costly repairs caused by use of improper fuel would
not be covered by your warranty.
To check the fuel availability, ask an auto club, or
contact a major oil company that does business
in the country where you will be driving.
Filling the Tank
{CAUTION:
Fuel vapor is highly ammable. It burns
violently, and that can cause very bad
injuries. Do not smoke if you are near
fuel or refueling your vehicle. Keep
sparks, ames and smoking materials
away from fuel.
The fuel cap can be on either or both sides of
your vehicle depending on option content.
To take off the cap, turn it slowly counterclockwise.
Fuel caps for all
gasoline applications,
and all diesel between
frame rail fuel tank
applicationsFuel caps for all side
mounted diesel
applications
264

{CAUTION:
If you get fuel on yourself and then
something ignites it, you could be badly
burned. Fuel can spray out on you if you
open the fuel cap too quickly. This spray
can happen if your tank is nearly full, and is
more likely in hot weather. Open the fuel
cap slowly and wait for any “hiss” noise to
stop. Then unscrew the cap all the way.
When you put the cap back on, turn it clockwise
until it is tight.
Notice:If you need a new fuel cap, be sure to
get the right type. Your dealer can get one
for you. If you get the wrong type, it may not
t properly. This may cause your malfunction
indicator lamp to light and may damage
your fuel tank and emissions system. See
Malfunction Indicator Lamp on page 174.If you have dual tanks, fill the driver’s side tank, or
forward tank, first. The fuel gage will give better
readings this way. Your gage will show the
total fuel left in both tanks.
If your vehicle is a C4/C5 model and you have
dual tanks, the engine must be off when refueling
or the fuel transfer system may become
inoperable.
If you have a single tank with dual fillers, where
there is a filler on each side of the vehicle, do not
attempt to fill the tank through both fillers at the
same time. Also, do not fill the tank with both caps
removed, as this may result in over-filling the
tank and fuel spillage.
265

To inspect the engine air cleaner/filter, remove the
filter from the vehicle and lightly shake the filter
to release loose dust and dirt. If the filter remains
caked with dirt, a new filter is required.
{CAUTION:
Operating the engine with the air cleaner/
lter off can cause you or others to be
burned. The air cleaner not only cleans the
air; it helps to stop ames if the engine
backres. If it is not there and the engine
backres, you could be burned. Do not
drive with it off, and be careful working on
the engine with the air cleaner/lter off.
Notice:If the air cleaner/lter is off, a backre
can cause a damaging engine re. And, dirt
can easily get into your engine, which will
damage it. Always have the air cleaner/lter in
place when you are driving.
Hood Inlet Seal
If your vehicle is being used in heavy snow
conditions or for snow plowing, there is a
possibility of snow and ice build up in the inlet to
the air cleaner, blocking airflow to the engine
and negatively impacting engine performance.
To prevent the blocking of air, remove the
hood inlet seal, by doing the following:
1. Loosen the clamp that holds the seal to the
air cleaner.
2. Slide Seal off.
281

{CAUTION:
You can be burned if you spill coolant on
hot engine parts. Coolant contains
ethylene glycol and it will burn if the
engine parts are hot enough. Do not spill
coolant on a hot engine.
1. You can remove the
coolant surge tank
pressure cap when
the cooling system,
including the coolant
surge tank pressure
cap and upper
radiator hose, is no
longer hot.
Turn the pressure cap slowly counterclockwise
about one full turn. If you hear a hiss, wait
for that to stop. A hiss means there is
still some pressure left.2. Then keep turning the pressure cap slowly,
and remove it.
3. Fill the coolant surge tank with the proper
mixture, to the FULL COLD mark.
293

Rear Axle Shift Motor
When to Check and Change Fluid
If you have an optional air-shift two-speed,
controlled traction, or locking differential type rear
axle, a good time to check the fluid level in the axle
shift motor is when the rear axle lubricant is
checked.
How to Check Fluid
Remove the plug on the front plate of the axle
shift motor, add enough fluid to raise the level to
the bottom of the filler plug hole, then replace
the plug.
What to Use
Refer to your Maintenance Schedule to determine
what kind of lubricant to use. SeePart C:
Recommended Fluids and Lubricants on page 397.
Four-Wheel Drive
Transfer Case
When to Check Lubricant
It is not necessary to regularly check transfer case
fluid unless you suspect there is a leak or you
hear an unusual noise. A fluid loss could indicate
a problem. Have it inspected and repaired.
How to Check Lubricant
A. Fill Plug
B. Drain Plug
312

To change an empty ether cylinder, follow
these steps.
1. Loosen the screw head on the
cylinder-to-bracket clamp.
2. Spread the clamp apart.
3. Clean any dirt from the neck of the cylinder
and the top of the valve before you take out
the cylinder.
4. Check the inside of the valve for any foreign
matter. Clean the valve as necessary.
5. Cover the valve to protect it from dirt and take
out the cylinder.
6. Install a new gasket whenever you take out
the cylinder. Use only one gasket and spread
a light film of clean oil on it before installation.
7. Put in the new cylinder. Turn it clockwise until
it just starts to contact the gasket.
8. Tighten the cylinder another half turn
(180 degrees). Don’t over-tighten.
9. Retighten the cylinder clamp.Front Wheel Bearings with
Oil-Filled Hubs
Notice:If you drive your vehicle through deep
water that is higher than the front or rear
axle, water may enter the axle housing and
cause the axle lubricant to break down.
This could damage the gears inside. Avoid
driving your vehicle through deep water.
You should avoid driving your vehicle through
deep puddles or standing water. If you must drive
through water that is higher than the front or
rear axle, see your dealer immediately afterward
to have the condition of the axle lubricant checked.
319