2007 CHEVROLET CORVETTE maintenance

A. Engine Oil Drain Plug
B. Seal
1. Remove the two engine oil drain plugs
from the bottom of the engine oil pan.
One drain plug drains the external oil tank
via the oil transfer supply line. The other
drain plug drains residual oil from the
crankcase sump. Allow the oil to drain.2. Once the oil has been drained from the
engine, remove the engine oil lter and
allow the oil to drain.
3. Re-install both drain plugs and tighten them
to 18 lb ft (25
Y).
4. Replace the oil lter and tighten it to
18 lb ft (25
Y). SeeNormal Maintenance
Replacement Parts on page 445for the
correct lter.
5. Oil is lled through the opening in the top
of the external engine oil tank. Remove the
oil ll cap.
6. Add eight quarts (7.6 L) of oil to the oil tank.
SeeCapacities and Specications on
page 426.
7. Install the oil ll cap and insert the dipstick,
if removed.
8. Start the engine and let it run at idle for at
least 15 seconds. This will circulate the
fresh engine oil through the lubrication system.
9. Shut off the engine and check the oil level
as described under “Checking Engine Oil
(Z06 Only).”
338

When to Inspect the Engine
Air Cleaner/Filters
Inspect the air cleaner/lters at the MaintenanceII
intervals and replace them at the rst oil change
after each 50,000 mile (83 000 km) interval.
SeeScheduled Maintenance on page 433for
more information. If you are driving in dusty/dirty
conditions, inspect the lters at each engine
oil change.
How to Inspect the Engine
Air Cleaner/Filters (6.0L V8 Engine)
To inspect the air cleaner/lters, remove the lters
from the vehicle and lightly shake the lters to
release loose dust and dirt. If the lters remain
caked with dirt, new lters are required.
To inspect or replace the engine air cleaner/lters,
do the following:1. Pull the latches on each side of the cover to
open, then move the latches up and out of
the way.
2. Push the air cleaner/lter cover toward the front
of the vehicle and then pull it up and away.
3. Inspect or replace the lter. SeeNormal
Maintenance Replacement Parts on page 445.
4. Reverse Steps 1 and 2 to replace the
air cleaner/lter cover.
5. Repeat the procedure for the second
air cleaner/lter.
343

How to Inspect the Engine
Air Cleaner/Filters (7.0L V8 Engine)
To inspect the air cleaner/lters, remove the lters
from the vehicle and lightly shake the lters to
release loose dust and dirt. If the lters remain
caked with dirt, new lters are required.
To inspect or replace the engine air cleaner/lters,
do the following:
1. Remove the screws holding the lter element
in place.
2. Pull on latches found on either side of the lter.3. Inspect or replace the lter. SeeNormal
Maintenance Replacement Parts on page 445.
4. Reverse Steps 1 and 2 to replace the
air cleaner/lter cover.
{CAUTION:
Operating the engine with the
air cleaner/lter off can cause you or
others to be burned. The air cleaner not
only cleans the air; it helps to stop ames
if the engine backres. If it is not there
and the engine backres, you could be
burned. Do not drive with it off, and be
careful working on the engine with the
air cleaner/lter off.
Notice:If the air cleaner/lter is off, a backre
can cause a damaging engine re. And, dirt
can easily get into your engine, which will
damage it. Always have the air cleaner/lter
in place when you are driving.
344

Hydraulic Clutch
It is not necessary to regularly check clutch uid
unless you suspect there is a leak in the system.
Adding uid will not correct a leak.
A uid loss in this system could indicate a
problem. Have the system inspected and repaired.
When to Check and What to Use
The hydraulic clutch
uid reservoir cap
has this symbol
on it. SeeEngine
Compartment Overview
on page 330for
reservoir location.Refer to the Maintenance Schedule to determine
how often you should check the uid level in
your clutch master cylinder reservoir and for
the proper uid to use. SeeOwner Checks
and Services on page 438andRecommended
Fluids and Lubricants on page 443.
How to Check and Add Fluid
Make sure the uid level is at the MIN (Minimum)
line on the side of the reservoir. If it is not,
remove the cap and add the proper uid until
the level reaches the MIN line.
346

Engine Coolant
The cooling system in your vehicle is lled with
DEX-COOL®engine coolant. This coolant is
designed to remain in your vehicle for ve years
or 150,000 miles (240 000 km), whichever
occurs rst, if you add only DEX-COOL
®
extended life coolant.
The following explains your cooling system
and how to add coolant when it is low. If you
have a problem with engine overheating,
seeEngine Overheating on page 350.A 50/50 mixture of clean, drinkable water and
DEX-COOL
®coolant will:
Give freezing protection down to−34°F (−37°C).
Give boiling protection up to 265°F (129°C).
Protect against rust and corrosion.
Help keep the proper engine temperature.
Let the warning lights and gages work as
they should.
Notice:Using coolant other than DEX-COOL
®
may cause premature engine, heater core,
or radiator corrosion. In addition, the engine
coolant may require changing sooner, at
the rst maintenance service after each
30,000 miles (50 000 km) or 24 months,
whichever occurs rst. Any repairs would
not be covered by your warranty. Always
use DEX-COOL
®(silicate-free) coolant in
your vehicle.
347

Brakes
Brake Fluid
The brake master
cylinder reservoir is
lled with DOT-3 brake
uid. SeeEngine
Compartment Overview
on page 330for the
location of the reservoir.
There are only two reasons why the brake uid
level in the reservoir might go down. The rst
is that the brake uid goes down to an acceptable
level during normal brake lining wear. When
new linings are put in, the uid level goes back
up. The other reason is that uid is leaking out of
the brake system. If it is, you should have the
brake system xed, since a leak means that
sooner or later the brakes will not work well.So, it is not a good idea to top off the brake
uid. Adding brake uid will not correct a leak.
If you add uid when the linings are worn,
then you will have too much uid when you get
new brake linings. You should add or remove
brake uid, as necessary, only when work is
done on the brake hydraulic system.
{CAUTION:
If you have too much brake uid, it can
spill on the engine. The uid will burn if
the engine is hot enough. You or others
could be burned, and your vehicle could
be damaged. Add brake uid only when
work is done on the brake hydraulic
system. See “Checking Brake Fluid” in
this section.
Refer to the Maintenance Schedule to determine
when to check the brake uid. SeeScheduled
Maintenance on page 433.
361

Replacing Brake System Parts
The braking system on a vehicle is complex.
Its many parts have to be of top quality and work
well together if the vehicle is to have really good
braking. Your vehicle was designed and tested
with top-quality brake parts. When you replace
parts of the braking system — for example, when
the brake linings wear down and you need new
ones put in — be sure you get new approved
replacement parts. If you do not, the brakes might
not work properly. For example, if someone puts
in brake linings that are wrong for your vehicle,
the balance between the front and rear brakes can
change — for the worse. The braking performance
you have come to expect can change in many other
ways if someone puts in the wrong replacement
brake parts.
Battery
Your vehicle has a maintenance free battery.
When it is time for a new battery, get one that
has the replacement number shown on the
original battery’s label. We recommend an
ACDelco
®replacement battery.For battery replacement, see your dealer or the
service manual. To purchase a service manual,
seeService and Owner PublicationsinService
Publications Ordering Information on page 468.
Warning:Battery posts, terminals, and related
accessories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive harm.
Wash hands after handling.
Vehicle Storage
If you are not going to drive your vehicle for
25 days or more, remove the black, negative (−)
cable from the battery. This will help keep
your battery from running down.
{CAUTION:
Batteries have acid that can burn you and
gas that can explode. You can be badly
hurt if you are not careful. SeeJump
Starting on page 365for tips on working
around a battery without getting hurt.
364

Windshield Replacement
Keep in mind that your windshield is part of the
Head-Up Display (HUD) system. If you ever have
to get your windshield replaced, be sure to get
one that is designed for HUD or your HUD image
may look blurred or out of focus.
Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected for
wear and cracking. SeeScheduled Maintenance
on page 433for more information.
Replacement blades come in different types and
are removed in different ways. For the proper type
and length, seeNormal Maintenance Replacement
Parts on page 445.It is a good idea to clean or replace the wiper
blade assembly every six months.
Allowing the wiper blade arm to touch the
windshield when no wiper blade is installed
could damage the windshield. Any damage that
occurs would not be covered by your warranty.
Do not allow the wiper blade arm to touch
the windshield.
To remove the wiper blade assembly,
do the following:
1. Open the hood to gain access to
the windshield wipers.
2. Lift the wiper arm away from the
windshield.
375