2007 CADILLAC XLR V buttons

Power Lumbar
The driver’s and
passenger’s seatback
lumbar support switches
are located on the
outboard sides of
the seats.
Use the power seat controls rst to get the proper
position, then continue with the lumbar adjustment.
Use the top lumbar switch to adjust support to
the middle seatback and the bottom lumbar switch
to adjust support to the lower seatback. Press
the front of the switch to increase support and the
rear of the switch to decrease support.
Keep in mind that as your seating position
changes, as it may during long trips, so should the
position of your lumbar support. Adjust the seat
as needed.
Heated and Cooled Seats
The buttons for the heated and cooled seats are
located on the climate control system.
((Heated/Cooled Seat):Press this button to
turn the feature on. The button on the left controls
the driver’s seat and the button on the right
controls the passenger’s seat. Each press of the
button will take you to a different setting. The
settings available in order are HI HEAT, LO HEAT,
OFF, HI COOL, LO COOL and OFF. You will be
able to feel the temperature change in a few
minutes.
The feature will automatically turn off when the
vehicle is turned off. SeeDual Climate Control
System on page 178for more information.
9

Memory Seat, Mirrors and Steering
Wheel
Your vehicle is equipped with the memory
package. The controls for these features are
located on the driver’s seat, and are used
to program and recall memory settings for the
driver’s seating positions.Use the following steps to program each button:
1. Adjust the driver’s seat including the seatback
recliner, lumbar, both outside mirrors and the
steering wheel to a comfortable position.
2. Press and hold button 1 until two beeps are
heard, then release the button.
A second mirror, seating and steering wheel
position can be programmed by repeating
the above steps and pressing button 2 (for
driver 2). Each time a memory button is pressed
and released, a single beep will sound. Each
time button 1 or 2 is pressed and released while
the vehicle is in PARK (P), the memory positions
will be recalled after a brief delay. If the vehicle
is not in PARK (P), three beeps will be heard and
the memory position will not be recalled.
When the engine is started, the seat, mirrors, and
steering wheel may automatically adjust to their
programmed positions.
To stop recall movement of the memory feature at
any time, press one of the power seat controls,
power mirror control buttons, memory buttons, or
power steering column control.
10

Two personalized exit positions can be set by rst
recalling the driving position (by pressing 1 or 2),
then positioning the steering wheel and seat in the
desired exit positions and then pressing and
holding the exit button until two beeps are heard.
The exit button is located between buttons 1 and 2.
With the vehicle in PARK (P), the exit position
for the previously set driver can be recalled
by pressing the exit button.
When you use the keyless access transmitter to
unlock your vehicle, automatic seat and steering
wheel movement to the exit position may
occur. The numbers on the back of the
transmitter, 1 and 2, corresponds to the numbers
on the memory buttons.
Further programming for automatic seat and mirror
movement can be done using the Driver
Information Center (DIC).
For programming information, seeDIC Vehicle
Personalization on page 220.Power Reclining Seatbacks
Your seats have power
reclining seatbacks.
Use the vertical power seat control located on the
outboard side of the seat to operate them.
To recline the seatback, press the control
toward the rear of the vehicle.
To raise the seatback, press the control
toward the front of the vehicle.
11

5. Turn the key ve times within ve seconds.
6. The Driver Information Center (DIC) will
display READY FOR FOB #X. X can be
2,3or4.
7. Place the new, unrecognized transmitter in
the glove box transmitter pocket with the
buttons facing to the right.
8. Once the transmitter is programmed, a beep
will sound. The DIC will display READY FOR
#X, where X can be 3 or 4, or MAX #
FOBS LEARNED.
9. Press the Acc. button.The Canadian immobilizer standard requires
Canadian owners to see their GM dealer
for matching new transmitters when a recognized
transmitter is not available. United States
owners are permitted to match a new transmitter
to their vehicle when a recognized transmitter
is not available. The procedure will require
three ten minute cycles to complete the matching
process. Do the following:
1. The vehicle must be off.
2. Place the new, unrecognized transmitter in
the glove box transmitter pocket with the
buttons facing to the right.
70

Battery Replacement
Under normal use, the battery in your keyless
access transmitter should last about three years.
You can tell the battery is weak if the transmitter
will not work at the normal range in any location. If
you have to get close to your vehicle before the
transmitter works, it is probably time to change the
battery.
A weak battery may also cause the DIC to display
NO FOB DETECTED when you try to start the
vehicle. If this happens, place the transmitter in the
glove box transmitter pocket with the buttons facing
to the right. Then, with the vehicle in PARK (P) or
NEUTRAL (N), press the brake pedal and the
START button. Although this will start the vehicle, it
is recommended that you replace the transmitter
battery as soon as possible. The DIC may display
FOB BATTERY LOW.
Notice:When replacing the battery, use care
not to touch any of the circuitry. Static
from your body transferred to these surfaces
may damage the transmitter.1. Insert a at object with a thin edge into the
slot on the side of the transmitter and
separate the bottom half from the top half.
2. Gently pull the battery out of the transmitter.
3. Put the new battery in the transmitter,
positive (+) side up. Use a battery, type
CR2032, or equivalent.
4. Reassemble the transmitter. Make sure to put
it together so water will not get in.
5. Test the transmitter.
72

From the inside, use the power door lock buttons
located at the top of the door panel near the
window. SeePower Door Locks on page 75for
more information.
To open a door from the inside, press the button in
front of the door handle and push the door open.
If power to the vehicle or the keyless access
transmitter is lost, there are two ways to open
the door.If you are inside the vehicle, use the door release
handle located on the oor next to each seat.
Pull the handle up to unlock and unlatch the door.
74

OnStar®service cannot work unless your vehicle
is in a place where OnStar®has an agreement
with a wireless service provider for service in that
area. OnStar
®service also cannot work unless
you are in a place where the wireless service
provider OnStar
®has hired for that area
has coverage, network capacity and reception
when the service is needed, and technology that
is compatible with the OnStar
®service. Not all
services are available everywhere, particularly in
remote or enclosed areas, or at all times.
OnStar
®service that involves location information
about your vehicle cannot work unless GPS
satellite signals are unobstructed and available in
that place as well.
Your vehicle must have a working electrical
system (including adequate battery power) for the
OnStar
®equipment to operate. There are other
problems OnStar®cannot control that may prevent
OnStar®from providing OnStar®service to you
at any particular time or place. Some examples are
damage to important parts of your vehicle in an
accident, hills, tall buildings, tunnels, weather
or wireless phone network congestion.
Your Responsibility
You may need to increase the volume of your
radio to hear the OnStar®advisor. If the light next
to the OnStar®buttons is red, this means that
your system is not functioning properly and should
be checked by a dealer. If the light appears
clear (no light is appearing), your OnStar
®
subscription has expired. You can always press
the OnStar®button to conrm that your OnStar®
equipment is active.
Universal Home Remote
System
Universal Home Remote System
(With One Triangular LED)
The Universal Home Remote System provides a
way to replace up to three hand-held
radio-frequency (RF) transmitters used to activate
devices such as garage door openers, security
systems, and home lighting.
110

This device complies with RSS-210 of Industry
Canada. Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation of the device.
The Canadian Registration ID number is
3521A-GTV06A.
Changes or modications to this system by other
than an authorized service facility could void
authorization to use this equipment.Universal Home Remote System
Operation (With Three Round LED)
Your vehicle may have the Universal Home Remote
System. If there are three round Light Emitting
Diode (LED) above the Universal Home Remote
System buttons, follow the instructions below. If
there is one triangular LED above the Universal
Home Remote System buttons, follow the
instructions under Universal Home Remote System
Operation (with one triangular LED).
This system provides a way to replace up to three
remote control transmitters used to activate
devices such as garage door openers, security
systems, and home lighting.
112