2007 CADILLAC STS V display

Make sure the Head-Up Display is on and
properly adjusted. If the HUD is not on, FCA will
not be enabled and you will not be provided
with FCA audible and visual warnings. See
Head-Up Display (HUD) on page 223for more
information.
{CAUTION:
On winding roads, FCA may not detect
a vehicle ahead. You could crash into
a vehicle ahead of you. Do not rely on
FCA on winding roads.
When weather limits visibility, such as
in fog, rain, or snow, FCA performance
is limited. There may not be enough
warning distance to the vehicle in front
of you. Do not rely on FCA in low
visibility conditions.
{CAUTION:
When FCA is enabled, the Adaptive Cruise
Control switch is on. If you press another
Adaptive Cruise Control button, you might
go into cruise when you do not want to.
You could be startled and even lose
control. Be careful not to press adaptive
cruise buttons unless you want to use
cruise control.
186

The mist and wash cycles operate as normal and
are not affected by the Rainsense™ function.
The Rainsense™ system can be overridden at any
time by manually turning the wiper band to low
or high speed.
When Rainsense™ is active, the headlamps will
turn on automatically. The headlamps will turn
off again once the wipers turn off if it is light
enough outside. If it is dark, they will remain on.
SeeWiper Activated Headlamps on page 215.
Notice:Do not place stickers or other items
on the exterior glass surface directly in front of
the moisture sensor. Doing this could cause
the moisture sensor to malfunction.
Windshield Washer
K(Washer Fluid):The lever on the right side
of the steering column also controls the windshield
washer. There is a button at the end of the
lever. To spray washer uid on the windshield,
press the button and hold it. The washer will spray
until you release the button. The wipers will
continue to clear the window for about six seconds
after the button is released and then stop or
return to your preset speed.
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
If the uid in the windshield washer uid reservoir
is low, the message CHECK WASHER FLUID
will appear on the Driver Information Center (DIC)
display. It will take 60 seconds after the bottle
is relled for this message to turn off. For
information on the correct washer uid mixture to
use, seeWindshield Washer Fluid on page 404
andRecommended Fluids and Lubricants on
page 516.
191

Engaging Adaptive Cruise Control With
the Set Button
{CAUTION:
If you leave your Adaptive Cruise Control
switch on when you are not using cruise,
you might hit a button and go into cruise
when you do not want to. You could be
startled and even lose control. Keep the
Adaptive Cruise Control switch off until
you want to use cruise control.
{CAUTION:
If you operate Adaptive Cruise Control
without your Head-up Display (HUD)
properly adjusted, your Adaptive Cruise
Control settings may not be visible. You
could forget your settings and be startled
by Adaptive Cruise Control response and
even lose control. Keep your HUD on and
properly adjusted when using Adaptive
Cruise Control.
The set speed is selected by the driver. This is the
speed you will travel if there is no vehicle
detected in your path.
200

To set Adaptive Cruise Control, do the following:
1. Make sure the Head-Up Display (HUD) is
on and properly adjusted. You cannot
engage Adaptive Cruise Control unless the
HUD is on. SeeHead-Up Display (HUD)
on page 223for more information.
2. Move the switch to on.
3. Get up to the speed you want.
4. Press in the set button at the end of the lever
and release it.
5. Take your foot off the accelerator pedal.
Once Adaptive Cruise Control is set, it may
immediately apply the brakes if it detects a vehicle
ahead is too close or moving slower than your
vehicle.This symbol will
appear on the Head-Up
Display (HUD) to
indicate that Adaptive
Cruise Control is active.
The number indicates
the set speed.
SeeHead-Up Display (HUD) on page 223for
more information.
Make sure the set speed is visible on the HUD so
you know the speed your vehicle will accelerate to if
a vehicle is not detected in your path. Keep in mind
speed limits, surrounding traffic speeds and
weather conditions when adjusting your set speed.
If your vehicle is in Adaptive Cruise Control when
the traction control system begins to limit wheel
spin, the Adaptive Cruise Control will automatically
disengage. SeeTraction Control System (TCS) on
page 323andStabiliTrak
®System on page 326.
When road conditions allow you to safely use it
again, you may turn the Adaptive Cruise Control
back on.
United States version
shown, Canada similar
201

Increasing Set Speed While Using Adaptive
Cruise Control
There are two ways to increase the set speed:
Use the accelerator to get to the higher speed.
Press the set button at the end of the lever,
then release the button and the accelerator
pedal. You will now cruise at the higher speed.
Move the Adaptive Cruise Control switch from
on to resume/increase. Hold it there until the
desired set speed is displayed in the HUD,
then release the switch. To increase your set
speed in very small amounts, move the
switch briey to resume/increase. Each time
you do this, your vehicle set speed will
increase by 1 mph (1.6 km/h).
Your vehicle will not reach the set speed until the
system determines there is not a vehicle in
front of you. At that point, your vehicle speed will
increase to the set speed.
Decreasing Set Speed While Using
Adaptive Cruise Control
Press in the set/decrease button on the end of the
lever until you reach the lower speed you want,
then release it.
To slow down in very small amounts, briey press
the set/decrease button. Each time you do this,
your set speed will be 1 mph (1.6 km/h) slower.
Resuming a Set Speed
Suppose you set your Adaptive Cruise Control at
a desired speed and then you apply the brake.
This will disengage the Adaptive Cruise Control.
But you do not need to reset it.
Once you are going about 25 mph (40 km/h) or
more, move the Adaptive Cruise Control
switch briey from on to resume/increase. Adaptive
Cruise Control will be engaged with the previously
chosen set speed.
202

Low-Speed Deactivation
If your speed falls below 20 mph (32 km/h) while
following a vehicle ahead, Adaptive Cruise Control
will begin to disengage. The driver alert symbol
on the HUD will ash and the warning beep
will sound. The driver must take action since
Adaptive Cruise Control will not slow the vehicle
to a stop.
Deactivation When Head-Up Display is
Turned Off
If you turn the HUD off when Adaptive Cruise
Control is engaged, it will begin to disengage. A
warning beep will sound and the message RADAR
CRUISE NOT READY will appear on the Driver
Information Center (DIC). SeeDIC Warnings
and Messages on page 264for additional
information. If Adaptive Cruise Control was braking
when the HUD is turned off, the braking will
continue briey.
Passing a Vehicle/Adaptive Cruise
Control Override
If you need to increase speed to pass a vehicle, use
the accelerator pedal. While you are doing this, the
system will not automatically apply the brakes. A
PEDAL APPLIED ACC OVERRIDE message will
appear on the HUD. SeeHead-Up Display (HUD)
on page 223for additional information. Once you
pass the vehicle and remove your foot from the
accelerator pedal, Adaptive Cruise Control will
return to normal operation and be able to apply the
brakes, if needed.
{CAUTION:
If you rest your foot on the accelerator
pedal, the system will not automatically
apply the brakes. You could crash into a
vehicle ahead of you. Do not rest your
foot on the accelerator pedal when using
Adaptive Cruise Control.
207

The high-beam headlamps are manually
turned on or you use the ash-to-pass feature.
SeeHeadlamp High/Low-Beam Changer on
page 183andFlash-to-Pass on page 188.
When either of these conditions occur,
the IntelliBeam™ feature is temporarily
disabled until the high-beam stalk is returned
to the neutral position. If either of these
conditions occur and IntelliBeam™ already
has the high-beam headlamps on, the
IntelliBeam™ feature is disabled and the
IntelliBeam™ light in the mirror turns off.
The exterior lamp control is turned to any
setting except AUTO.
When this occurs, IntelliBeam™ is disabled
until the control is turned back to the
AUTO position and the AUTOMATIC LIGHTS
ON message displays on the DIC.
The IntelliBeam™ system is turned off at the
inside rearview mirror.
The vehicle’s speed drops below
15 mph (24 km/h).IntelliBeam™ may not turn off the high-beams if
the system cannot detect other vehicle’s lamps
because of any of the following:
The others vehicle’s lamp(s) are missing,
damaged, obstructed from view, or otherwise
undetected.
The other vehicle’s lamp(s) are covered with
dirt, snow and/or road spray.
The other vehicle’s lamp(s) cannot be detected
due to dense exhaust, smoke, fog, snow, road
spray, mist, or other airborne obstructions.
Your vehicle’s windshield is dirty, cracked, or
obstructed by something that blocks the view
of the IntelliBeam™ light sensor.
Your vehicle’s windshield is covered with ice,
dirt, haze, or other obstructions.
Your vehicle is loaded such that the front end
of the vehicle points upward, causing the
IntelliBeam™ sensor to aim high and
not detect headlamps and taillamps.
You are driving on winding or hilly roads.
You might need to manually disable or cancel the
high-beam headlamps by turning the low-beam
headlamps on, if any of the above conditions exist.
214

Instrument Panel Brightness
This feature controls the
brightness of the
instrument panel lights.
Press in the center knob on the DIC control panel
until the knob pops out. Then turn the knob
clockwise to brighten the lights or counterclockwise
to dim them. If you turn the knob completely
clockwise, the interior lamps will turn on.
Entry Lighting
The entry lighting system turns on the reading and
dome lamps and the backlighting to the exterior
lamp control when a door is opened or if you
press the remote keyless entry transmitter
unlock button. If activated by the transmitter, the
lighting will remain active for about 25 seconds.
The entry lighting system uses the light sensor; it
must be dark outside in order for the lamps to
turn on. The lamps turn off about 25 seconds after
the last door is closed. They will dim to off if the
ignition is on, or immediately deactivate if the
power locks are activated.
Parade Dimming
This feature prohibits dimming of the instrument
panel displays and backlighting during daylight
hours when the key is in the ignition and the
headlamps are on. This feature operates with the
light sensor and is fully automatic. When the
light sensor reads darkness outside and the
parking lamps are active, the instrument panel
displays can be adjusted by turning the instrument
panel brightness knob. SeeInstrument Panel
Brightness on page 220for additional information.
Base Level Shown,
Uplevel Similar
220