2007 CADILLAC STS Owners Manual

If the engine is off, the windows may be closed
from outside the vehicle using the lock button
on the keyless access transmitter. Press and hold
the lock button for more than two seconds to
close any open window(s) on your vehicle. If any
window is unable to close completely, it will
reverse and the horn will chirp. See “Anti-Pinch
Feature” underPower Windows on page 105
for more information.
You can program your vehicle so the turn signal
indicators will not ash and the horn will not sound
when pressing the lock button on the keyless
access transmitter. For more information
see “Lights Flash at Lock” and “Horn Chirps at
Lock” underVehicle Personalization on page 148.
/(Remote Start):Press this button to operate
the remote start feature. See “Remote Vehicle
Start” at the end of this section for more detailed
information.
"(Unlock):Press this button once to unlock
the driver’s door. The turn signal indicators will
ash twice. Press the unlock button twice within
ve seconds to unlock all the doors. If it is dark
enough outside, your interior lamps will come on.You can program your vehicle so the turn signal
indicators will not ash and the fog lamps and
reverse lamps remain on steady for about
20 seconds when the keyless access transmitter is
used to unlock the vehicle. See “Lights Flash at
Lock” and “Ext. (Exterior) Lights at Unlock” under
Vehicle Personalization on page 148.
If your vehicle has the memory feature you can
program and recall memory settings when you
press the unlock button on the keyless access
transmitter. SeeMemory Seat, Mirrors and Steering
Wheel on page 169for more information.
G(Trunk):Press and hold this button for
about one second to open the trunk while
the engine is turned off or the shift lever is in
PARK (P).
L(Vehicle Locator/Panic Alarm):Press and
release this button to locate your vehicle. The horn
will chirp three times and the turn signal lamps
will ash three times. Press and hold the button for
three seconds to sound the panic alarm. The
horn will chirp and the turn signal lamps will ash
for 30 seconds. Press and release the button
again to cancel the panic alarm.
89

Matching Transmitter(s) to Your
Vehicle
Each Keyless Access System is coded to allow
only transmitters programmed to your vehicle
to work. If a transmitter is lost or stolen, a
replacement can be purchased and programmed
through your dealer. Your dealer can reprogram
your vehicle so lost or stolen transmitters no longer
work with your vehicle. Each vehicle can have a
maximum of four transmitters matched to it.
To match a new transmitter to your vehicle when
you have a recognized transmitter, do the
following. Two recognized transmitters are required
for Canadian owners.
1. The vehicle must be off.
2. Have the recognized transmitter and the new,
unrecognized transmitter(s) with you.
3. Insert the vehicle key into the key lock
cylinder located on the outside of the
driver’s door.4. Turn the key to the unlock position
ve times within ve seconds.
5. The Driver Information Center (DIC)
will display READY FOR FOB X,
where X can be 2, 3 or 4.
90

6. Place the new, unrecognized transmitter into
the transmitter pocket with the transmitter
buttons facing the front of the vehicle.
The transmitter pocket is inside the center
console storage area located between
the driver and front passenger seats.7. Once the transmitter is programmed,
a beep will sound. The DIC will display
READY FOR X, where X can be 3 or 4,
or MAX # FOBS LEARNED.
8. Remove the transmitter from the transmitter
pocket and press the unlock button on the
keyless access transmitter two times.
The Canadian immobilizer standard requires
Canadian owners to see their dealer for matching
new transmitters when a recognized transmitter
is not available. United States owners are
permitted to match a new transmitter to their
vehicle when a recognized transmitter is
not available.
91

The procedure will require three, ten minute cycles
to complete the matching process. Do the following:
1. The vehicle must be off.
2. Place the new, unrecognized transmitter into
the transmitter pocket with the transmitter
buttons facing the front of the vehicle.
The transmitter pocket is inside the center
console storage area located between
the driver and front passenger seats.
3. Insert the vehicle key into the key lock
cylinder located on the driver’s door.
92

4. Turn the key to the unlock position ve times
within ve seconds.
5. The DIC message will display OFF/ACC TO
LEARN.
6. Press the Acc. button (ignition switch).
7. The DIC will read WAIT 10 MINUTES and will
count down to zero, one minute at a time.
8. The DIC will display OFF/ACC TO LEARN
again.
9. Press the Acc. button (ignition switch) again.
10. The DIC will again read WAIT 10 MINUTES
and will count down to zero, one minute
at a time.
11. The DIC will display OFF/ACC TO
LEARN again.
12. Press the Acc. button (ignition switch) again.
13. The DIC will again read WAIT 10 MINUTES
and will count down to zero, one minute
at a time.14. A beep will sound and the DIC will read
READY FOR FOB 1. At this time, all
previously known transmitters have been
erased.
15. Once the transmitter is recognized and
programmed, a beep will sound and the
DIC will display READY FOR FOB 2.
16. Remove the keyless access transmitter and
press the unlock button twice to initialize it.
If you have additional transmitters to program, this
process can be repeated until four transmitters
have been programmed. The DIC will then display
MAX # FOBS LEARNED and will exit the
programming mode.
When you are done programming transmitters,
press the unlock button on each keyless access
transmitter twice. After performing this process,
transmitters previously programmed will no longer
work with your vehicle and must be reprogrammed.
93

Battery Replacement
Under normal use, the battery in your keyless
access transmitter should last about three years.
The battery is weak if the transmitter will not
work at the normal range in any location. If you
have to get close to your vehicle before the
transmitter works, it is probably time to change the
battery. The DIC may display KEY FOB
BATTERY LOW.
A weak battery may also cause the DIC to display
NO FOBS DETECTED when you try to start
the vehicle. If this happens, place the transmitter
in the center console storage area transmitter
pocket with the buttons facing to the front of the
vehicle. Then, with the vehicle in PARK (P)
or NEUTRAL (N), press the brake pedal and the
start button. SeeStarting the Engine on page 113,
for additional information about your vehicle’s
electronic keyless ignition with push button start.
Although this will start the vehicle, it is
recommended that you replace the transmitter
battery as soon as possible.Notice:When replacing the battery, use care
not to touch any of the circuitry. Static
from your body transferred to these surfaces
may damage the transmitter.
94

To replace the battery, do the following:
1. Depending on which keyless access
transmitter you have, Insert a at object with a
thin edge into the slot on the side or back
of the transmitter and separate the bottom half
from the top half.
2. Carefully pull the battery out of the transmitter.
3. Put the new battery in the transmitter,
positive (+) side down. Use a battery
type CR2032 or equivalent.4. Reassemble the transmitter. Make sure to put
it together so water will not get inside the
transmitter.
5. Test the transmitter.
Remote Vehicle Start
This feature allows you to start the engine from
outside the vehicle.
Before the remote vehicle start system can be
operated with the keyless access transmitter
it must be activated. The remote start system is
turned on through the vehicle personalization
system.
You can also program the remote vehicle start
system to start up the vehicle’s automatic climate
control system. If this feature is turned on, the
system monitors the outside temperature and turns
on the rear window defogger, front window
defogger, and heated or ventilated seats, if your
vehicle has them. See “Personal Settings
Menu” underVehicle Personalization on page 148.
95

/(Remote Start):To start the vehicle using the
remote start feature, do the following:
1. Aim the remote keyless access transmitter at
the vehicle.
2. Press the transmitter’s lock button, release it,
and then immediately press and hold the
transmitter’s remote start button for at least
three seconds or until the vehicle’s turn signal
lamps ash. The vehicle’s doors will be
locked.
When the vehicle starts, the parking lamps will
turn on and remain on while the vehicle is
running.
3. If it is the rst remote start since the vehicle
has been driven, repeat these steps, while
the engine is still running, to extend the engine
running time by 10 minutes. Remote start
can be extended one time.If the vehicle is left running it will automatically
shut off after 10 minutes unless a time extension
has been done. To manually shut off a remote
start, do any of the following:
Aim the keyless access transmitter at the
vehicle and press the remote start button until
the parking lamps turn off.
Turn on the hazard warning ashers.
Press the Acc. button (ignition switch). See
Ignition Positions on page 111.
Turn on the valet lockout switch. SeeValet
Lockout Switch on page 110.
When you enter the vehicle during a remote start,
press the brake pedal and press the start
button on the keyless ignition switch to transition
from remote start operation to normal vehicle
operation.
Laws in some local communities may restrict the
use of remote starters. For example, laws may
require a person using remote start to have
the vehicle in view when doing so. Check local
regulations for any requirements on remote starting
of vehicles.
96