2007 BUICK RANDEZVOUS tow

3. The seat can then be lifted off the front
oor pins.
4. Remove the seat by rocking it slightly toward
the rear of the vehicle and then pulling it out.
Installing the Captain Chairs
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not
provide the protection needed in a crash.
The person wearing the belt could be
seriously injured. After installing the seat,
always check to be sure that the safety
belts are properly routed and attached,
and are not twisted.
24

3. Push the rear of the seat down to lock the
rear latches onto the rear set of oor pins.
{CAUTION:
A seat that is not locked into place
properly can move around in a collision or
sudden stop. People in the vehicle could
be injured. Be sure to lock the seat into
place properly when installing it.4. Push and pull on the seat to check that it is
properly attached.
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
5. Return the seatback to the upright position.
Stowable Seat
The stowable seat is a two passenger bench seat
that comes with the rear convenience center.
SeeRear Convenience Center on page 165. The
stowable seat can be removed or, with the
seatback folded, lie at with the convenience
center.
26

Folding the Seatback
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
To fold the seatback
forward, lift the lever
located on the back of
the seat. Push the
seatback down until it is
locked into place.
Push and pull on the seatback to make sure that it
is locked into place.To raise the seatback, do one of the following:From the rear of the vehicle, lift the lever
to release the seatback. Then pull the
strap, located on the right side of the seat, to
lift the seatback up. The seatback has a
pocket on the side to stow the strap.
From the passenger’s side door, lift the lever
to release the seatback. Lift the seatback
and push it until it locks in place.
Push and pull on the seatback to make sure that it
is locked into place.
27

Removing the Stowable Seat
1. Remove the convenience center, if it is in the
vehicle. SeeRear Convenience Center on
page 165.
2. Make sure all items are off the stowable seat.
3. From the front of the seat, remove the
two nuts, located on the oor on each side of
the seat.
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
4. From behind the bench seat, fold the seatback
down. See “Folding the Seatback” previously.
5. Remove the rear nuts located on the oor on
each side of the seat.
6. Remove the seat by rocking it slightly toward
the rear of the vehicle and then pulling it out
the vehicle. This should be done in one
motion.
7. Put the nuts back onto the screws so the nuts
do not get misplaced.
Installing the Stowable Seat
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not
provide the protection needed in a crash.
The person wearing the belt could be
seriously injured. After installing the seat,
always check to be sure that the safety
belts are properly routed and attached,
and are not twisted.
Do not put the stowable seat in so that it faces
rearward. The stowable seat has to be installed
before the rear convenience center. SeeRear
Convenience Center on page 165for more
information.
28

The stowable seat has seat position labels,
located on the back of the seat, showing where
the seat must go. The seat must be placed in the
proper location for the legs to attach correctly.
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
1. Make sure that the seatback is folded forward
before beginning this procedure. See “Folding
the Seatback” previously.
2. Remove the nuts from the screws.
3. Place the stowable seat on the vehicle oor
so that the seat brackets are placed over the
screws.
4. Reinstall the nuts onto the screws. Torque to
approximately 18 lb ft (25
Y).
{CAUTION:
A seat that is not locked into place
properly can move around in a collision or
sudden stop. People in the vehicle could
be injured. Be sure to lock the seat into
place properly when installing it.
5. Try to raise the seat to make sure that it is
locked into place.
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
6. Raise the seatback to its upright position.
Push and pull on the seatback to make
sure that it is locked into place.
29

Center Rear Passenger Position
Lap-Shoulder Belt
If your vehicle has a bench seat, someone can sit
in the center position.
When you sit in the center seating position, you
have a lap safety belt, which has no retractor. You
also have a shoulder belt, which has a retractor.
In order to have the protection of the shoulder belt,
you must rst connect it to the lap belt.
1. Remove the shoulder belt from its stowage
location in the roof and pull it all the way
down to the lap belt.
51

{CAUTION:
Never do this.
Here two children are wearing the same
belt. The belt can not properly spread the
impact forces. In a crash, the two children
can be crushed together and seriously
injured. A belt must be used by only one
person at a time.
Q:What if a child is wearing a lap-shoulder
belt, but the child is so small that the
shoulder belt is very close to the child’s
face or neck?
A:If the child is sitting in a seat next to a
window, move the child toward the center of
the vehicle. Also seeRear Safety Belt
Comfort Guides on page 53. If the child is
sitting in the center rear seat passenger
position, move the child toward the safety belt
buckle. In either case, be sure that the
shoulder belt still is on the child’s shoulder, so
that in a crash the child’s upper body would
have the restraint that belts provide.
58

Child Restraint Systems
An infant car bed (A), a special bed made for use
in a motor vehicle, is an infant restraint system
designed to restrain or position a child on a
continuous at surface. Make sure that the infant’s
head rests toward the center of the vehicle.A rear-facing infant seat (B) provides restraint with
the seating surface against the back of the
infant. The harness system holds the infant in
place and, in a crash, acts to keep the infant
positioned in the restraint.
64