2007 BUICK LUCERNE ignition

• Trip A and Trip B
• Fuel Range (until empty)
• Average Fuel Economy
• Instantaneous
Fuel Economy
• Average Speed
(Trip/Fuel):Press this button to
scroll through the following trip and fuelinformation:(Set/Reset):Press this button to reset
DIC information while it is displayed or toacknowledge a warning message.
Getting to Know YourLucerne4
Your vehicle’s Driver Information Center
(DIC) provides vehicle feature customization,vehicle information, and vehicle warning
messages. The DIC messages will be shown
on your instrument panel cluster display. TheDIC buttons are located on the instrument
panel to the left of the steering wheel. Tooperate the DIC, the ignition switch must bein the Run position.
See Section 3 of your Owner Manual.
(Vehicle Information):Press this
button to scroll through the following vehicleinformation:
• Oil Life Remaining
• Units (English/Metric)(Customization):Press this button to
scroll through the customization settings.
To program customization settings:
1. Place the vehicle in Park (P).
2. Press the (Customization) button to
enter the Feature Settings menu andscroll through the available features.
3. Press the (Set/Reset) button to
access the settings for the feature beingdisplayed.
4. Press the button to scroll through the
available settings.
5.Press the button to choose the set
ting being displayed and move to the nextfeature.
Driver Information Center

(Unlock): Press this
button to unlock the driver’s
door. Press it again within
five seconds to unlock allremaining doors. The
approach lighting can beprogrammed using the DIC.(Lock): Press this button
when all doors are closed toimmediately lock all the doors.RKE feedback (light flashand/or horn chirp) can be programmed using the DIC.
If the Delayed Lock feature is
enabled and the Lock buttonis pressed while any door isopen, the doors will not lockfor approximately 10 seconds.
Remote Vehicle Start (if equipped) and Remote Keyless Entry
(Remote Vehicle Start): This feature
can be used to start the engine from outside
the vehicle. The remote start capability mustbe turned on using the Driver InformationCenter (DIC).
To remote start the vehicle:
1. Aim the transmitter at the vehicle.
(Extended remote start transmitter
range is within 196 feet (60 meters) of
the vehicle.)
2. Press and release the Lock button on the
transmitter.3. Immediately press and hold the Remote
Start button for about four seconds. Whenthe vehicle starts, the parking lamps will
light. The engine will continue running for10 minutes.
4. Repeat these steps for a 10minute time
extension. Only two consecutive remotestarts are allowed.
When you enter the vehicle after a remote
start, the key must be inserted in the ignitionand turned to the Run position before driving.
5
Your Remote Keyless Entry (RKE) transmitter allows you to lock and unlock your vehicle and
perform other functions from up to 60 feet away from the vehicle.
(Remote Trunk
Release): Press this button
to release the trunk lid. Thetrunk may also be opened by
pressing the Trunk Release button on the left side of theinstrument panel.
See Section 2 of your Owner Manual.
(Remote Alarm):Press this button to sound
the alarm. The horn will
sound and the headlampswill flash for two minutes.Press the button again orturn the ignition key to theRun position to cancel thealarm. The vehicle must be
turned off to use the alarm.
SAFETY & SECURITY

Automatic Recall of the Easy Exit Seat
The easy exit seat can be programmed using
the Driver Information Center (DIC) to automatically recall the seat exit setting when thekey is removed from the ignition.
To program the easy exit seat:
1.Press the (Customization) button
until Easy Exit Seat appears on the DIC
display.
2.Press the (Set/Reset) button to
access the feature settings.
3. Press the button to scroll through the
settings of Off, On, or No Change.
4. With your choice displayed, press the
button to change the setting.
Automatic Recall of the Memory Seat
The memory seat can be programmed using
the Driver Information Center (DIC) to automatically recall the memory seat settingwhen the Remote Keyless Entry transmitterunlock button is pressed.
To program the memory seat:
1. Press the (Customization) button until
Memory Seat Recall appears on the DIC
display.
2. Press the (Set/Reset) button to
access the feature settings.
3. Press the button to scroll through the
settings of Off, On, or No Change.
4. With your choice displayed, press the
button to change the setting.
9
See Section 3 of your Owner Manual.