2007 BUICK LUCERNE headlamp

(Unlock): Press this
button to unlock the driver’s
door. Press it again within
five seconds to unlock allremaining doors. The
approach lighting can beprogrammed using the DIC.(Lock): Press this button
when all doors are closed toimmediately lock all the doors.RKE feedback (light flashand/or horn chirp) can be programmed using the DIC.
If the Delayed Lock feature is
enabled and the Lock buttonis pressed while any door isopen, the doors will not lockfor approximately 10 seconds.
Remote Vehicle Start (if equipped) and Remote Keyless Entry
(Remote Vehicle Start): This feature
can be used to start the engine from outside
the vehicle. The remote start capability mustbe turned on using the Driver InformationCenter (DIC).
To remote start the vehicle:
1. Aim the transmitter at the vehicle.
(Extended remote start transmitter
range is within 196 feet (60 meters) of
the vehicle.)
2. Press and release the Lock button on the
transmitter.3. Immediately press and hold the Remote
Start button for about four seconds. Whenthe vehicle starts, the parking lamps will
light. The engine will continue running for10 minutes.
4. Repeat these steps for a 10minute time
extension. Only two consecutive remotestarts are allowed.
When you enter the vehicle after a remote
start, the key must be inserted in the ignitionand turned to the Run position before driving.
5
Your Remote Keyless Entry (RKE) transmitter allows you to lock and unlock your vehicle and
perform other functions from up to 60 feet away from the vehicle.
(Remote Trunk
Release): Press this button
to release the trunk lid. Thetrunk may also be opened by
pressing the Trunk Release button on the left side of theinstrument panel.
See Section 2 of your Owner Manual.
(Remote Alarm):Press this button to sound
the alarm. The horn will
sound and the headlampswill flash for two minutes.Press the button again orturn the ignition key to theRun position to cancel thealarm. The vehicle must be
turned off to use the alarm.
SAFETY & SECURITY

Getting to Know YourLucerne16
Automatic Lamp Control
Your vehicle is equipped with an Automatic Lamp Control system, which automatically turns
on the headlamps and other exterior lamps, and the instrument panel lights, at night or when
necessary.
The Automatic Lamp Control system’s light sensor is located on top of the instrument panel.
To ensure proper system operation, it’s important to avoid placing any objects on or near the
sensor.
The exterior lamps also can be operated manually. The exterior lamp control knob
is located on the left side of the instrument panel.
Exterior Lamps
(On/Off):This position
turns off theexterior lamps,excluding theDaytimeRunningLamps.
(Parking
Lamps): This
position turns onthe parkinglamps, taillampsand instrumentpanel lights.
AUTO (Automatic):This position automati
cally turns on theAutomatic LampControl system.
(Fog Lamps)(if equipped): Push
in the knob to turnon the fog lamps.Push it again to turn
off the fog lamps.
(Headlamps):This posi
tion turns on the headlamps,parking lamps, taillamps andinstrument panel lights.
This feature uses four ultrasonic sensors on
the rear bumpers to help you avoid collidingwith objects when parking the vehicle. Itoperates only at speeds less than 5 mph.
The rear parking assist display is located
near the rear window. The lights on the dis
play provide distance information. As thevehicle approaches an object, the number oflights illuminated increases. Lowtoned
Ultrasonic Rear Park Assist (if equipped)
beeps also sound from the rear speakers
when objects are near the rear bumper.
Be sure to keep the ultrasonic sensors on
the vehicle’s rear bumper clean to ensureproper operation.
The system can be disabled using the Driver
Information Center.
See Section 3 of your Owner Manual.
See Section 3 of your Owner Manual.

The Rainsense™ II windshield wipers use a moisture sensor to automatically operate the
wipers when needed, depending on driving conditions and the sensitivity setting. If the system
is left on for long periods, an occasional wipe may occur without any moisture on the windshield to indicate the system is activated.
The headlamps and parking lamps also will be turned on automatically when the Rainsense
wipers are active if the exterior lamp control switch is in the AUTO position. The controls for thewindshield wipers are located on the multifunction stalk on the left side of the steering column.
Rainsense™ II Windshield Wipers (if equipped) and Heated Washer
Fluid (if equipped)
(Washer Fluid):Push the paddle on
top of the multifunction lever to spray washerfluid on the windshield.
(Sensitivity Setting): Rotate
the control band up to one of thesensitivity levels to activate the
Rainsense function. The wipersactivate more often as the bandis rotated upward.
(High):Rotate the
control band
up to this position to turn thewipers on the High setting.
17
(Heated Washer
Fluid): Slide and
release this switch tostart four automaticheated wash/wipecycles.The first cycle may take up to 45 seconds tooccur before thewasher fluid
is heated. Theremaining cycles
may take up to 20
seconds to occur.
The system determines the amount offluid and activates
the wipers. To cancelany remainingwash/wipe cycles,slide and release theswitch again.
(Low):Rotate the
control band
up to this position to turn thewipers on the Low setting.
(Off):Rotate the
control band to this posi
tion to turn off the wipers.(Mist):Rotate the
control band down tothis position to turn thewipers on for one wipe.
See Section 3 of your Owner Manual.
Note: Turn off the
Rainsense wipers beforeentering an automaticcar wash to preventwiper damage.