2007 Acura TL lock

µ
µ
µµ µ
µ To
avoid transmission damage, come
to a complete stop before shifting
into Park. The shift lever must be in
Park before you can remove the key
from the ignition switch.
Use this position for
your normal driving. The transmis-
sion automatically adjusts to keep
the engine at the best speed for the
driving conditions.
ForfasteraccelerationwheninD,
you can get the transmission to
automatically downshift by pushing
the accelerator pedal to the floor.
The transmission will shift down one,
two or three gears, depending on
your speed.
Press
the brake
pedal to shift from Park to reverse.
To shift from neutral to reverse,
come to a complete stop and then
shift.
Your vehicle has a reverse lockout so
you cannot accidentally shift to
reverse from neutral or any other
driving position when the vehicle
speed exceeds 5 6 mph (8 10
km/h).
If you cannot shift to reverse when
the vehicle is stopped, press the
brake pedal, slowly shift to neutral,
andthenshifttoreverse.
If there is a problem in the reverse
lockout system, or your vehicle’s battery
is disconnected or goes dead,
you cannot shift to reverse. (Refer to
on page ).
Use neutral if you
need to restart a stalled engine, or if
it is necessary to stop briefly with
the engine idling. Shift to the Park
position if you need to leave your
vehicle and apply the parking brake.
Press on the brake pedal when you
are moving the shift lever from
neutral to another gear.
This position mechani-
cally locks the transmission. Use
Park whenever you are turning off or
starting the engine. To shift out of
Park, you must press on the brake
pedal and have your foot off the
accelerator pedal.
If you have done all of the above and
still cannot move the lever out of
Park, see on
page . 258 258
To shift from:
PtoR
RtoN
NtoD DtoL
LtoD
DtoN NtoR RtoP Do this:
Press the brake pedal, then
move the shift lever.
Move the lever.
Drive (D)
Reverse (R)
Shif t L ock Release
Neutral (N)
Park (P)
Shif t L ock Release
Automatic Transmission
254
——
y

y
(%yy

à
à
à
àà
à
à
à
To shift from
21
32
43
54 Speed range
under 29 mph
(47 km/h)
under 56 mph
(90 km/h)
under 93 mph
(150 km/h)
under 130 mph
(209 km/h)
To release the reverse lockout, make
sure the ignition switch is in the
ACCESSORY(I) position.Make sure the ignition switch is in
the LOCK (0) position. Set the parking brake.
This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal does not work. This procedure
is also used to release the reverse
lockout. If you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
rpm below the red zone.
When you are in Sequential
SportShif t mode, and the vehicle is
stopped, push f orward on the shif t
lever to shif t to second gear. You will
see ‘‘2’’ in the display. Starting out in
second gear will help to reduce
wheelspin in deep snow or on a
slippery surf ace. To shift from
21
32
43
54 Speed range
under 37 mph
(54 km/h)
under 61 mph
(98 km/h)
under 93 mph
(150 km/h)
under 130 mph
(209 km/h)
1.
2.
Type S only
Shif t L ock Release Engine Speed L imiter
Starting in Second Gear
Automatic Transmission
258
——
y
y
(%yy

Put a cloth on the edge of the shif t
lock release slot cover. Using a
small f lat-tipped screwdriver or a
metal f ingernail f ile, caref ully pry
on the edge of the cover to remove
it.Remove the key from the shift
lock release slot. Press the brake
pedal, and restart the engine.
If you need to use the shif t lock
release, it means your vehicle is
developing a problem. Have the
vehicle checked by your dealer.
Insert a key into the shift lock
release slot.
Push down on the key and move
the shift lever out of Park to
neutral.
To release the reverse lockout,
move the shift lever from neutral
to reverse, then to Park.
3. 6.
5. 4.
Automatic Transmission
Driving
259
SHIFT LOCK RELEASE SLOT
COVER
——
y
y
(%yy

Always use the parking brake when
you park your vehicle. Make sure
the parking brake is set f irmly, or
your vehicle may roll if it is parked
on an incline.
If your vehicle has an automatic
transmission, set the parking brake
bef ore you put the transmission in
Park. This keeps the vehicle f rom
moving and putting pressure on the
parking mechanism in the
transmission.Make sure the moonroof and the
windows are closed.
Turn of f the lights.
Place any packages, valuables, etc.,
in the trunk or take them with you.
Lock the doors.
Never park over dry leaves, tall
grass, or other f lammable
materials. The hot three way
catalytic converter could cause
these materials to catch on fire.
If the vehicle is f acing uphill, turn
the front wheels away from the
curb. If you have a manual
transmission, put it in f irst gear.If the vehicle is f acing downhill,
turn the front wheels toward the
curb. If you have a manual
transmission, put it in reverse gear.
Make sure the parking brake is
f ully released bef ore driving away.
Driving with the parking brake
partially set can overheat or
damage the rear brakes.
Parking T ips
Parking
260
——
y
y
(%yy

Check the brakes after driving
through deep water. Apply the
brakes moderate ly to see if they feel
normal. If not, apply them gently and
frequently until they do. Be extra
cautious in your driving.
Your
vehicle is equipped with disc
brakes at all four wheels. A power
assist helps reduce the effort needed
on the brake pedal. The anti-lock
brake system (ABS) helps you retain
steering control when braking very
hard.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their effective-
ness. Use the engine to assist the
brakes by taking your foot off the
accelerator and downshifting to a
lower gear.
Resting
your foot on the brake pedal
applies the brakes slightly. This
builds up heat, and reduces brake
effectiveness and brake pad life. In
addition, fuel economy can be
reduced. It also keeps your brake
lights on all the time, confusing
drivers behind you. The
hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the vehicle (the left-front brake is
connected with the right-rear brake,
etc.). If one circuit should develop a
problem, you will still have braking
at two wheels, but the brake pedal
may not f eel normal (see page f or more inf ormation). If the brake pads need replacing, you
will hear a distinctive, metallic
screeching sound when you apply
the brake pedal. If you do not have
the brake pads replaced, they will
screech all the time and braking
ef f ectiveness could be reduced. It is
normal for the brakes to occasionally
squeal or squeak when you apply
them.
326
Braking System Design
Brake Wear Indicators
Braking System
Driving
261
——
y
y
(%yy

The anti-lock brake system (ABS)
helpspreventthewheelsfrom
locking up, and helps you retain
steering control by pumping the
brakes rapidly, much faster than a
person can do it.
The electronic brake distribution
(EBD) system, which is part of the
ABS, also balances the front-to-rear
braking distribution according to
vehicle loading.
Let the ABS work for you by always
keeping firm, steady pressure on the
brake pedal. This is sometimes
referred to as ‘‘stomp and steer.’’ You
will feel a pulsation in the brake
pedal when the ABS activates, and
may hear some noise. This is normal:
it is the ABS rapidly pumping the
brakes. On dry pavement, you will
need to press on the brake pedal
very hard before the ABS activates.
However, you may feel the ABS
activate immediately if you are trying
to stop on snow or ice. If
this indicator comes on, the anti-
lock function of the braking system
has shut down. The brakes still work
like a conventional system, but
without anti-lock. You should have
your dealer inspect your vehicle as
soon as possible.
If the indicator comes on while
driving, test the brakes as instructed
on page . 326
You should never pump the brake pedal.
ABS Indicator
Anti-lock Brakes (ABS)
262
——
y
y
(%yy

If the ABS indicator and the brake
system indicator come on together,
and the parking brake is fully
released, the EBD system may also
be shut down.
Test your brakes as instructed on
page . If the brakes f eel normal,
drive slowly and have your vehicle
repaired by your dealer as soon as
possible. Avoid sudden hard braking
which could cause the rear wheels to
lock up and possibly lead to a loss of
control.
The VSA indicator will come on
alongwiththeABSindicator. such as trying to take a
corner too f ast or making a sudden
lane change. Always drive at a safe
speed f or the road and weather
conditions.
Always steer moderately
when you are braking hard. Severe
or sharp steering wheel movement
can still cause your vehicle to veer
into oncoming traffic or off the road. on loose or
uneven surf aces, such as gravel or
snow, than a vehicle without anti-
lock.
It only helps with steering
control during braking.
326 Important Saf ety Reminders
A BS will not prevent a skid that
results f rom changing direction
abruptly,
A BS cannot prevent a loss of
stability. A vehicle with A BS may require a
longer distance to stop
A BS does not reduce the time or
distance it takes to stop the
vehicle.
Anti-lock Brakes (ABS)
Driving
263
——
y
y
(%yy

Let the engine run f or several
minutes, then check the drain bolt
and oil f ilter f or leaks. Reinstall the engine oil f ill cap.
Start the engine. The oil pressure
indicator should go out within 5
seconds. If it does not, turn of f the
engine and check your work.
Engine oil change capacity
(including f ilter): Refill the engine with the
recommended oil. Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten the drain bolt to: Install a new oil f ilter according to
the instructions that come with it.
Remove the oil f ilter, and let the
remaining oil drain. A special
wrench (available from your
dealer) is required. Turn of f the engine and let it sit
f or several minutes, then check
the oil level on the dipstick. If
necessary, add more oil.
Make sure the oil f ilter gasket is
not stuck to the engine block. If it
is, remove it bef ore installing a
new oil f ilter.
3. 7.
8.
9.
5.
6. 4.
Changing the Oil and Filter
Maint enance
285
OIL FILTER
4.5 US qt (4.3)
29 lbf·ft (39 N·m , 4.0 kgf·m)
Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container, and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.
——
y
y
(%yy