2007 Acura RDX audio

µµThe SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
SEEK/SKIP bar, then release it. The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see ‘‘SCAN’’
on the upper display. To activate the scan function with
the interf ace dial, press the AUDIO
button to view the audio control
display, then push down the selector
on the interf ace dial, and push the
selector to the right. You will see
‘‘SCAN’’ on the audio control display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 10 seconds. If you do
nothing, the system will then scan
f or the next strong station and play it
f or 10 seconds. When it plays a
station that you want to listen to,
press the SCAN button again, or
push the interface selector to the
right again.
To activate the seek function with
the interf ace dial, press the AUDIO
button to view the audio control
display, then push the selector on
the interface dial to the right or left.
CONT INUED
SEEK SCA N
Audio System
Features
203
SEEK ICONS
SCAN INDICATORSCAN ICON
——
y
y
() yy

µµ
Each preset button/icon
can store one f requency on AM and
two f requencies on FM. To view the
preset icons on the audio control
display, push the AUDIO button. Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button (icon).
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Pick a preset number (1 6), you
want for that station. Press the
preset button, and hold it until you
hear a beep.
To store the f requency on a preset
icon, turn the interf ace dial to
select a desired preset icon. The
selected preset icon will be
highlighted. Press and hold
ENTER on the selector f or more
than 2 seconds to store the
f requency.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
1.
2.
3.
4.
Audio System
Preset
204
PRESET ICONS
——
y
y
() yy

µTo
activate AUTO SELECT, press
the AUDIO button to view the audio
control display. Push the interface
selector down to scroll down the
display, turn the dial to A. SEL, then
press ENTER on the interface
selector. You will see ‘‘AUTO SEL’’
fl ashing in the audio control display,
and ‘‘A. SEL’’ on the upper display.
Then, the system goes into scan
mode for several seconds.
If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area. If
you do not like the stations auto
select has stored, you can store
other frequencies on the preset
buttons (icons) as previously
described.
To turn off auto select, press
ENTER on the interface selector
(press the A.SEL button) again. This
restores the presets you originally
set.
For information on AM/FM radio
frequencies and reception, see page
.
For information, see page .
You will see ‘‘0’’ displayed if auto
select cannot f ind a strong station f or
every preset button. Press the A.SEL button. You will see
AUTO SEL on the screen, and the
system goes into scan mode f or
several seconds. The system stores
the f requencies of six AM and
twelve FM stations in the preset
buttons. 227
231
On Canadian models
Audio System
AUTO SELECT
Radio Frequencies and Reception
Adjusting the Sound
Features
205
AUTO SEL INDICATOR
A.SEL ICON
——
y

y
() y
y

On RDX with Technology Package model
Audio System
Operating the CD Changer
206
Normal modeMP3/WMA mode
SCAN INDICATOR FOLDER NUMBER
WMA MODE INDICATOR
MP3 MODE INDICATOR
U.S. model is shown. DISC NUMBER
TRACK NUMBER
SCAN INDICATOR
——
y
y
() y

y

CONT INUED
Audio System
Features
207
INTERFACE DIAL
AUDIO BUTTON
LOAD BUTTON SCAN BUTTON DISP/MODE BUTTON
EJECT BUTTON
TUNE/FOLDER BAR
DISC/AUX BUTTON
DISC LOAD INDICATOR
PRESET BUTTONS
DISC SLOT
PWR/VOL KNOB
U.S. model is shown.
SEEK/SKIP BAR
——
y
y
() y
y

Your vehicle’s audio system has an
in-dash disc changer with the same
controls used for the radio. To
operate the disc changer, the ignition
switch must be in the ACCESSORY
(I) or the ON (II) position.
The disc changer can play these disc
formats: CD (CD-DA)
CD-R/RW
DVD-A
DTS
The disc packages or jackets should
have one of these marks. DVD-A
discs not meeting DVD
verifica tion standards may not be
playable.
The changer cannot play DVD-V or
DVD-R/RW formats.
Some CD-DA and CD-ROM mixed
discs are not playable.
‘‘DTS’’ and ‘‘DTS Digital Surround’’
are registered trademarks of Digital
Theater Systems, Inc.
You cannot load and play 3-inch
(8-cm)discsinthissystem. The changer can also play MP3 or
WMA format (see page ). 212
Audio System
208
TM
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.
——
y
y
() y
y

To load multiple discs in one
operation:Press and hold the LOAD button
on the changer unit until you hear
a beep. You will see ‘‘BUSY’’ on
the upper display, and the disc
load indicator turns red and starts
blinking.
Insert the disc into the disc slot
when the disc load indicator turns
green and ‘‘LOAD’’ appears in the
upper display at the same time.
Insert it only half way; the drive
will pull it in the rest of the way.
You will see ‘‘BUSY’’ on the upper
display, and the disc load indicator
turns red again and blinks as the
CD is loaded.
When the disc load indicator turns
green and ‘‘LOAD’’ appears on the
upper display again, insert the
next CD in the slot. Repeat steps 1 through 3 until all
six positions are loaded. If you are
not loading all six positions, press
the LOAD button again after the
last CD has loaded. ‘‘DISC READ’’
appears on the upper display, then
the system begins playing the last
loaded.
If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 10 seconds, stop the load
operation, and begin playing the last
disc loaded.
To load a single disc: Press and release the LOAD
button on the changer unit. You
will see ‘‘BUSY’’ on the upper
display, and the disc load indicator
turns red and starts blinking. Insert a disc into the disc slot
when the disc load indicator turns
green, and ‘‘LOAD’’ appears on
the upper display at the same time.
Insert the disc only about half way;
the drive will pull it in the rest of
the way. You will see the disc
number blinking on the upper
display, and the disc load indicator
turns red again and blinks as the
CD is loaded.
Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
Youwillsee‘‘DISCREAD’’onthe
upper display, then the system
begins to play the CD. Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
1.
2.
3. 4.
1.
3. 2.
CONT INUED
L oading CDs in the Changer
Audio System
Features
209
——
y

y
() y
y

You can load a CD into an empty
position while a CD is playing. Press
the AUDIO button to view the audio
control display. Select the empty
position (‘‘No Disc’’ is shown on the
audio control display) by rotating the
interf ace dial. Then press ENTER on
the selector to enter your selection.
The current CD stops playing and
starts the loading sequence. The CD
just loaded will play.You can also select the empty
position by pressing the appropriate
preset button.
You can load a disc(s) in any mode
(AM,FM,XMradio,orAUX)if you
do not select an empty position.
You cannot select the empty position
if there is no disc in the changer.
Audio System
210
EMPTY POSITION
——
y

y
() y
y