2007 Acura RDX display

ÛÝÛ
Ý
When
you set the temperature to its
lowest limit ( ) or its highest
limit ( ), the system runs at
full cooling or heating only. It does
not regulate the interior temperature.
In cold weather, the fan will not
come on automatically until the
heater starts to develop warm air. Press
the DUAL button to select
dual temperature control mode (see
page ). The indicator in the
DUAL button comes on.
You can manually select various
f unctions of the climate control
system when it is in the AUTO mode.
All other f eatures remain
automatically controlled.
Making any manual selection causes
thewordAUTOinthedisplaytogo
out.
To adjust the desired temperature,
push or of the temperature
control buttons. Select the f an speed by pressing the
fan control buttons ( or
). The f an speed is
represented by vertical bars in the
display. When you press the DUAL button
again (indicator turns of f ), both
sides adjust to the driver’s side
temperature.
Press the A/C button to turn the air
conditioningonandoff.Youwillsee
A/C ON or A/C OFF in the display.
When you turn the A/C of f , the
system cannot regulate the inside
temperature if you set the
temperature control below the
outside temperature.175
Climate Control System
Dual Button
Semi-automatic Operation
T emperature Control Fan Control A ir Conditioning (A /C) Button
172
——
y

y
() y
y

If you press the OFF button, the
climate control system shuts of f
completely.
Air flows from the center
and corner vents in the dashboard.
Airf low is divided between
the vents in the dashboard and the
f loor vents.
Air f lows f rom the f loor
vents.
Airf low is divided between
the f loor vents and the def roster
vents at the base of the windshield. To keep stale air and mustiness
f rom collecting, you should have
the f an running at all times. Keep the system of f f or short
periods only.
The mode indicator in the display
changes to the current mode each
time you press the button.
When the climate control system is
turned off, the temperature in the
display will also turn of f .
Use the MODE button to select the
vents the air flows from. Some air
will f low f rom the dashboard corner
vents in all modes.
To Turn Everything Off
Mode Button
Climate Control System
174
——
y

y
() y
y

Û
Ý When you set the temperature to its
lower or upper limit, it is displayed as or .
Push AUTO or . The selected
temperatures appear in the display.
When the indicator in the DUAL
button is off, you can adjust both
sides to the same temperature by
adjusting the driver’s side
temperature control buttons ( or ).
Dual Temperature Control
176
DRIVER’S SIDE PASSENGER’S SIDE
——
y
y
() y

y

XM satellite radio information is
available on page .
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM or
FM button. On the FM band, ‘‘ST’’
will be shown on the center display if
the station is broadcasting in stereo.
Stereo reproduction on AM is not
available. The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Turn the system on by
pushing the PWR/VOL knob, or the
AM or FM button. Adjust the volume
by turning the PWR/VOL knob.
193
On U.S. models
On RDX model
Audio System
To Play the AM/FM Radio
180
STEREO
INDICATOR
FM BUTTON
SCAN BUTTON
TUNE/FOLDER BAR AM BUTTONSCAN
INDICATOR
A.SEL
INDICATOR
A.SEL/RDM BUTTON VOLUME
LEVEL
PWR/VOL KNOB
PRESET BARS
SEEK/SKIP BAR
U.S. model is shown.
——
y
y
() y
y

µ
µ µµ
µ
µ
CONT INUED
You can use any of f ive methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN, the
preset bars, and AUTO SELECT. Use the TUNE/FOLDER
bar to tune the radio to a desired
f requency. Press the side of the
bar to tune to a higher f requency,
and the side of the bar to tune
to a lower f requency.
The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
SEEK/SKIP bar, then release it. If youpressandholdthe or side of the bar, the f requency
will begin to change rapidly. It will
stop when you release it. The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see ‘‘SCAN’’
on the center display. The system
will scan f or a station with a strong
signal. When it f inds one, it will stop
and play that station for about 10
seconds.
If you do nothing, the system will
then scan f or the next strong station
andplayitfor10seconds.Whenit
plays a station you want to listen to,
press the SCAN button again. Each side of the bars (1
6) can store one f requency on AM
and two f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each side of
the preset bar.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Pick the preset number (1 6), f or
the station you want to store.
Press the lef t or right side of the
bar,andholdituntilyouheara
beep.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
1.
2.
3.
4.
To Select a Station
TUNE
SEEK
SCA N
Preset
Audio System
Features
181
——
y

y
() y
y

µµ If
you do not like the stations auto
select has stored, you can store
other frequencies on the preset bars.
,pressthe
A. SEL/RDM button. This restores
the presets you originally set. For
information on AM/FM radio
frequencies and reception, see page
.
For information, see page .
If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area.
To activate it, press the A. SEL/
RDM button. ‘‘A. SEL’’ will f lash on
the center display, and the system
will go into scan mode f or several
seconds. It stores the f requencies of
six AM and twelve FM stations in
the preset bars (1 6).
You will see ‘‘0’’ displayed if auto
select cannot f ind a strong station f or
every preset bar. 231
196
To turn of f auto select
Audio System
Radio Frequencies and Reception
Adjusting the Sound
AUTO SELECT
182
——
y

y
() y
y

To load a single disc:Press and release the LOAD
button on the changer unit. You
will see ‘‘BUSY’’ on the center
display, and the disc load indicator
turns red and starts blinking.
Insert a disc into the disc slot
when the disc load indicator turns
green and ‘‘LOAD’’ appears on the
center display at the same time.
Insert the disc only about half way;
the drive will pull it in the rest of
the way. You will see the disc
indicator blinking on the center
display.
To load multiple discs in one
operation:
When the disc load indicator turns
green and ‘‘LOAD’’ appears on the
center display again, insert the
next CD in the slot.
Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
Repeat steps 1 through 3 until all
six positions are loaded. If you are
not loading all six positions, press
the LOAD button again after the
last CD has loaded. ‘‘DISC READ’’
appears on the center display, then
the system begins playing the last
CD loaded.
If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 10 seconds, stop the load
operation, and begin playing the last
disc loaded.
Press and hold the LOAD button
on the changer unit until you hear
a beep. You will see ‘‘BUSY’’ on
the center display, and disc load
indicator turns red and starts
blinking.
Insert the disc into the disc slot
when the disc load indicator turns
green and ‘‘LOAD’’ appears on the
center display at the same time.
Insert it only half way; the drive
will pull it in the rest of the way.
You will see ‘‘BUSY’’ on the center
display, and the disc load indicator
turns red again and blinks as the
CD is loaded.
Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
1.
2.
3.
1.
2. 4.
Audio System
L oading CDs in the Changer
186
——
y
y
() y

y

µ
CONT INUED
The CD changer can play CD-Rs and
CD-RWs compressed in MP3 and
WMA format. When playing a disc in
MP3 or WMA, you will see ‘‘MP3’’ or
‘‘WMA’’ on the center display. A disc
can support more than 99 f olders,
and each folder can hold up to 255
playable f iles.
When there are more than 99 f olders
in a disc, the center display only
shows two digits.
If the disc has a complex structure, it
will be a while to read the disc bef ore
the system begins to play it.
Select the CD changer by pressing
the CD/AUX (U.S. model) or CD
(Canadian model) button. You will
see ‘‘CD’’ on the center display. The
system will begin playing the last
selected CD in the CD changer. You
will see the disc and track numbers
displayed.
When the system reaches the end of
the disc, the system will advance to
the next disc and begin to play. To
select a dif f erent disc, press an
appropriate side of the preset bar (1
6). If you select an empty position
in the CD changer, the system will
try to load the CD in the empty slot.
Youwillsee‘‘DISCREAD’’onthe
center display, then the system
begins to play the CD.
You can load a disc(s) in any mode
(AM,FM,XMradio,orAUX)if you
do not select an empty position.
If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded. You can load a CD into an empty
position while a CD is playing. Select
the empty position (the disc
indicator is not shown on the center
display) by pressing the appropriate
side of the preset bars. The current
CD stops playing and starts the
loading sequence. The CD just
loaded will play. 3.
Audio System
Playing an MP3/WMA Disc
To Play a CD
Features
187
——
y
y
() y
y