2007 Acura MDX turn signal

Press and release the Talk button.
Af ter the beep, say ‘‘Yes.’’ The
HFL response is ‘‘Preparing to
delete Eric’s phone.’’ Say ‘‘OK’’ to
continue. Otherwise, say ‘‘Go back,’’
or ‘‘Cancel.’’
Press and release the Talk button.
If you say ‘‘OK’’ af ter the beep, the
HFL response is ‘‘The phone has
been deleted. Returning to the
main menu.’’ If you say ‘‘Go back,’’
or ‘‘Cancel,’’ the phone will not be
deleted.
Press and release the Talk button.
Af ter the beep, say ‘‘Phone setup.’’
The HFL response is ‘‘Phone
setup options are status, pair, edit,
delete, and list.’’
Press and release the Talk button.
Af ter the beep, say ‘‘List.’’ The
HFL responds by listing the name
of each paired phone. When allphones paired to the system have
been read, the HFL response is
‘‘The entire list has been read.
Returning to the main menu.’’
Press and release the Talk button.
Af ter the beep, say ‘‘Phone setup.’’
The HFL response is, ‘‘Phone
setup options are status, pair, edit,
delete, and list.’’
Press and release the Talk button.
After the beep, say ‘‘Status.’’ An
example of the HFL response is,
‘‘Eric’s phone is linked. Battery
strength is three bars. Signal
strength is f ive bars, and the
phone is roaming. Returning to the
main menu.’’
Press and release the Talk button.
Af ter the beep, say ‘‘Next phone.’’
The HFL response is ‘‘Searching
f or the next phone.’’ The HFL
then disconnects the linked phone
and searches for another paired
phone. If no other phones are
f ound, the f irst phone remains
linked.
1.
2. 1. 2.
1.
4.
5.
To list all paired phones, do this: To f ind out the status of the phone being
used, do this: To change f rom the currently linked
phone to another paired phone, do this:
HandsFreeL ink
Features
285
TM
——y
y
()-yy

Your vehicle is equipped with a tire
pressure monitoring system (TPMS)
that turns on every time you start the
engine and monitors the pressure in
your tires while driving.
Each tire has its own pressure
sensor. If the air pressure of a tire
becomes signif icantly low, the
sensor in that tire immediately sends
a signal that causes the low tire
pressure indicator in the instrument
panel to come on. If this happens,
you will see which tire is losing
pressure on the multi-inf ormation
display along with a ‘‘CHECK TIRE
PRESSURE’’ message.When the low tire pressure indicator
is on, one or more of your tires is
signif icantly underinf lated. You
should stop and check your tires as
soon as possible, and inf late them to
the proper pressure as indicated on
the vehicle’s tire inf ormation placard.
It is possible that the pressures
shown on the multi-inf ormation
display and the pressures you
manually measure are slightly
dif f erent.
If the dif f erence is signif icant or you
cannot make the low tire pressure
indicator and message on the multi-
inf ormation display go out af ter
inf lating the tires to the specif ied
values, have your dealer check the
system as soon as possible.
Becausetirepressurevariesby
temperature and other conditions,
the low tire pressure indicator may
come on unexpectedly. Driving on a signif icantly under-
inf lated tire causes the tire to
overheat and can lead to tire failure.
Under-inf lation also reduces f uel
efficiency and tire tread life, and may
af f ect the vehicle’s handling and
stopping ability. If the tire is f lat, or if the tire
pressure is too low to continue
driving, replace the tire with the
compact spare tire.
CONT INUED
Tire Pressure Monitoring System (TPMS)
Low Tire Pressure
Indicator
Driving
343
——y
y
()-yy

µ
´
Trailer lights and equipment must
comply with f ederal, state, province,
and local regulations. Check trailer
light requirements f or the areas
where you plan to tow, and use only
equipment designed f or your vehicle. If you use a non-Acura trailer
lighting harness and converter, you
cangetthematingconnectorand
pins that mate with the connector in
your vehicle f rom your dealer.
Since lighting and wiring vary with
trailer type and brand, you should
also have a qualif ied mechanic install
a suitable connector between the
vehicle and the trailer.
Your vehicle is equipped with a
connector to install an optional trailer
lighting connector that mates with
your vehicle. You can get this
optional connector f rom your dealer. Ref er to the above illustration f or
wiring information.
We recommend that you have your
dealer install an Acura wiring
harness and converter. This harness
has been designed f or your vehicle.
Towing a Trailer
Trailer Lights
Driving
363
BACK-UPLIGHT ( )
TAILLIGHTS ELECTRIC BRAKE
ACCESSORY OPTION
TRAILER HAZARD
LIGHT
RIGHT TURN
SIGNAL BRAKE
DIAGNOSTIC
TRAILER BACK-UP LIGHT
B CHARGE
LEFT TURN
SIGNAL
ILLUMINATION
LIGHTS
——y
y
()-yy

Under these conditions, trailer
stability assist begins to stabilize the
vehicl e/trailer combination by
reducing the vehicle speed. The
control unit sends signals to
selectively apply the brakes and
regulate the engine output. The
brake lights of your vehicle will be
turned on automatically by the
system even if you do not keep the
pressu re on the brake pedal.
Your
vehicle is equipped with trailer
stability assist function. This
function works on the same sensors
as the vehicle stability assist (VSA)
system. This function helps to
stabilize the vehicl e/trailer
combination when the trailer
severely sways or oscillates. For
more information of the VSA system,
see page .
When the brakes are applied, the
trailer’s brake lights come on along
wi th the vehicle brake lights.
When the trailer stability assist
activates, you will see the VSA
activation indicator blink. There may
also be some noise from the VSA
hydraulic system. Trailer
stability assist cannot prevent
a loss of control. Always reduce the
ve hicle speed and steer firmly. Do
not brake suddenly or make quick
steering motion. It could cause the
trailertojackknifeorturnoverand
the system becomes ineffective.
Trailer stability assist cannot prevent
swaying that can occur in crosswinds
and in normal and emergency
driving maneuvers. It helps only to
stabilize the vehicl e/trailer
combination in these conditions,
after the oscillation becomes severe.
If
the function detects the vehicle/
trailer instability, it checks if the
swaying is caused by the trailer, and
if the trailer swaying or oscillation is
increasing.
The vehicle/trailer combination is
more affected by crosswinds,
buffeting, and improper tongue load.
These conditions can make the
trailer unstable, and cause it to sway. Always obey the recommended
speed limits f or towing a trailer, see
page . Trailer stability assist will also be
inef f ective while driving at high
speed or towing a trailer with a high
center or gravity.
351
365
T railer Stability A ssist
Driving
367
——y
y
()-yy

Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Insert
the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working.
Open the hood.
Remove the f ront bulkhead cover
(see page ).
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
1.
2.
3.
4.
5.
5.
6.
7.
6.
7.
386
Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
Lights
398
BULB
BULB
SOCKET
FRONT TURN SIGNAL LIGHT
PARKING LIGHT
SOCKET
——y
y
()-yy

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb f rom the f og
light assembly by turning it one-
quarter turn counterclockwise.Remove the two bolts, and remove
the rear light assembly f rom the
rear pillar.
Open the tailgate. Use a
screwdriver protected with a cloth
to pry open the two covers.
Determine which of the two bulbs
is burned out: turn signal/hazard
lights or side marker light.
1. 2.
3.
3.
4.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
400
CONNECTOR
INNER FENDER COVER
BOLT
BOLT
——y
y
()-yy

Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working. Place the cover back into the light
assembly. Push it up until it locks
in place. Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
4.
5. 6.
2.
3. 7.
Lights
Side T urn Signal L ight
Rear L icense Plate Bulb
402
BULB
SOCKET
——y
y
()-yy

µ µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Î
Î
Specifications
T
echnical Inf ormat ion
447
Battery Engine Fuses
Tires Alignment
Lights
60 W
12 V
12 V 35 W
12 V 5 W
12 V 5 W
8W
5W
2W
3.4 W
12
V
12 V
12 V
12 V
The low beam headlights are high voltage discharged type.
Replacement of a low beam headlight bulb should be performed by
your dealer.
Capacity 12 V Type
BorexStroke
Displacement
Compression
ratio
Spark plugs 11.0
: 1
223.5
cu-in (3,664 cm
)
3.54
x 3.78 in (90.0 x 96.0 mm)
Water
cooled 4-stroke SOHC
VTEC V6 gaso line engine
Interior
Rear
Under-hood
12
V
12
V
21 W
3CP
SKJ20DR-M11
12
V 3 CP
12
V 18 W
12
V 3 CP
21
W
12 V
12
V 3.4 W
55
W
12 V
12
V 3 CP
60
W
12 V
12 V 65
AH/5 HR
76 AH/20 HR
Size
Pressure
60 psi (420 kPa , 4.2 kgf/cm
)
32
psi (220 kPa , 2.2 kgf/cm)
T165/80D17
104M
P255/55R18
104H
Toe-in
Camber
Caster
4°12’0°30’ 0°30’
0.08
in (2.0 mm)
0.00
in (0.0 mm)
Headlights
Daytime
running light
Front side marker lights
Front turn signal lights
Parking lights
Fog light
Front foot lights
Rear turn signal lights
Rear side marker light
Backup lights
License plate lights
Individual map lights
Cargo area light
Tailgate light
Vanity mirror light
Door light IZFR6K-11
See page442or the fuse label
attached to the inside of the fuse
box lid.
See page441or the fuse label
attached to the inside of the fuse
box lid.
See page440and441or the fuse
box cover.
Front/Rear
Spare
Front/Rear
Spare
Front
Rear
Front
Rear
Front
Front
Rear High
Low
: (H11) (HB3)
(D2S)
(HB3)
DENSO:
NGK:IN
——y

y
()-yy