2007.5 Peugeot 307 ignition
[x] Cancel search: ignitionPage 117 of 212
DRIVING
104
Cancelling the memorised
reference speed
When the vehicle becomes
stationary, after switching off the
ignition, the system no longer
memorises a speed.
Contact a PEUGEOT dealer to have
the system checked. When changing the memo-
rised reference speed by
means of a maintained press,
pay attention as the speed
can increase or decrease rapidly.
Do not use the cruise control on
s l i p p e r y r o a d s o r i n h e a v y t r a f i c .
In the event of a steep slope,
the cruise control cannot prevent
the vehicle from exceeding the
programmed speed.
In any event, the cruise control cannot
replace the need to comply with
speed limits, nor can it replace the
need for vigilance and responsibility
on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- n e v e r i t o n e m a t o n t o p o f another.
Reactivating the cruise control
After cancellation of the cruise
control,
press button 4 . Your vehicle
will return to the last memorised
speed. The display indicates (e.g. at
70 mph (110 km/h)):
Changing the memorised
reference speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
press button 3 ;
A brief press increases by 1 mph
(1 km/h).
An extended press increases by
5 mph (5 km/h).
A maintained press increases in
steps of 5 mph (5 km/h).
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 . Switching the function off
Place dial 1 in position 0 to switch
the system off.
Operating fault
In the event of a cruise control
malfunction, the memorised speed
i s e r a s e d , t h e d a s h e s l a s h f o r a f e w
seconds:
To memorise a speed lower than the
previous one:
press button 2 ; A brief press decreases by 1 mph (1 km/h). An extended press decreases by 5 mph
(5 km/h).
A maintained press decreases in steps
of 5 mph (5 km/h).
Page 119 of 212
DRIVING
106
Reactivating the cruise control
After cancellation of the cruise
control, press button 4 . Your vehicle
will return to the last memorised
speed. The display indicates (e.g. at
70 mph (110 km/h)):
Cancelling the memorised
reference speed
When the vehicle is stationary,
after the ignition has been
switched off, the system no longer
stores any speed.
Changing the memorised
reference speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
press button 3 ;
A brief press increases by 1 mph
(1 km/h).
An extended press increases by
5 mph (5 km/h).
A maintained press increases in
steps of 5 mph (5 km/h).
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 . Switching the function off
Place dial 1 in the OFF position to
switch the system off.
Operating fault
In the event of a cruise control
malfunction, the memorised speed
i s e r a s e d , t h e d a s h e s l a s h f o r a f e w
seconds:
Contact a PEUGEOT dealer to have
the system checked. When changing the memo-
rised reference speed by
means of a maintained press,
pay attention as the speed
can increase or decrease rapidly.
Do not use the cruise control on
s l i p p e r y r o a d s o r i n h e a v y t r a f i c .
In the event of a steep slope,
the cruise control cannot prevent
the vehicle from exceeding the
programmed speed.
In any event, the cruise control
cannot replace the need to observe
the speed limits, nor can it replace the
need for vigilance and responsibility
on the part of the driver.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is positioned correctly.
- n e v e r i t o n e m a t o n t o p o f another. To memorise a speed lower than the
previous one:
press button 2 ;
A brief press decreases by 1 mph (1 km/h).
An extended press decreases by 5 mph
(5 km/h).
A maintained press decreases in steps
of 5 mph (5 km/h).
Page 127 of 212
CHECKS
115
CHECKING THE LEVELS
There are two marks on
the dipstick:
A = maximum
N e v e r i l l p a s t t h i s m a r k .
B = minimum
Oil change
According to the information given in
the servicing booklet.
Viscosity selection
In all cases, the oil selected must
meet the manufacturer’s require-
ments.
Note: the coolant does not need to
be changed.
Dipstick
Cooling system
U s e t h e l u i d r e c o m m e n d e d b y t h e
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. This fan can oper-
ate with the ignition off.
I n t h e c a s e o f v e h i c l e s i t t e d w i t h
a p a r t i c l e e m i s s i o n i l t e r , t h e f a n
can operate after the vehicle has
s t o p p e d , e v e n w h e n t h e e n g i n e i s
cold.
In addition, as the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying out any work.
Slacken the cap by two turns to re-
lease the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and
top up the level.
Windscreen and headlamp
w a s h l e v e l
Diesel additive level (Diesel
w i t h p a r t i c l e e m i s s i o n f i l t e r )
If the service warning light comes on,
accompanied by a message and an
audible signal, this indicates a low
diesel additive level.
This additive must be topped up.
Contact a PEUGEOT dealer as soon
as possible.
Brake fluid level
* According to engine.
Oil level
To maintain the reliability of
engines and emission control
systems, the use of additives
in engine oil is prohibited.
The level should always be
above the MIN mark and
close to the MAX mark.
P o w e r s t e e r i n g r e s e r v o i r
Remove the style trim * (see §
"Changing a bulb - Front lights").
Open the reservoir, with the engine
at ambient temperature. The level
should always be above the MIN.
mark and close to the MAX. mark.
For best quality cleaning and
for your safety, we would ad-
vise that you use products
recommended by PEUGEOT.
Check the level regularly and
top up between changes. The
maximum consumption is 0.5 l
per 600 miles (1 000 km).
Check the level with the ve-
hicle level, engine cold, using the oil
level gauge on the instrument panel
or the dipstick. Replacement must be car-
ried out according to the
manufacturer’s servicing
schedule.
U s e l u i d s r e c o m m e n d e d b y
t h e m a n u f a c t u r e r , w h i c h f u l i l D O T 4
standards.
Page 132 of 212
10PRACTICAL INFORMATION
119
Putting the wheel back in place
Put the wheel back in place.
Unscrew the yellow central bolt a
few turns, then put it in place in
the centre of the wheel.
Tighten the central bolt fully until it
c l i c k s t o s e c u r e t h e w h e e l i r m l y .
Put the tool holder back in the
centre of the wheel and clip it.
P u t t h e b o o t l o o r b a c k i n p l a c e .
W h e e l s i t t e d w i t h t h e T y r e U n d e r -
I n l a t i o n D e t e c t i o n s y s t e m
For further information refer to "Tyre
u n d e r - i n l a t i o n d e t e c t i o n " i n t h e
safety section.
The wheel must be positioned
l a t , i n t h e c e n t r e o f i t s
housing.
F o r y o u r s a f e t y , a l w a y s
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- w i t h i r s t o r r e v e r s e g e a r e n g a g e d (position P for the automatic
gearbox),
- with the vehicle chocked.
N e v e r g o u n d e r n e a t h a v e h i c l e t h a t i s
s u p p o r t e d o n l y b y a j a c k ( u s e a r a m p ) .
* According to model and country. A f t e r c h a n g i n g t h e w h e e l :
- have the tightening of the bolts
and the tyre pressure checked by
a PEUGEOT dealer as soon as
possible,
- have the punctured tyre repaired a n d r e i t i t t o t h e v e h i c l e a s s o o n
as possible.
R e c o m m e n d a t i o n s w h e n u s i n g
t h e t e m p o r a r y s p a r e w h e e l *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, it must be replaced as
quickly as possible.
Observe the following instructions to
avoid altering the behaviour of the
vehicle:
-
do not exceed 50 mph (80 km/h) ,
- d o n o t i t a w h e e l t r i m ,
- drive with care,
- check the tyre pressure indicated
on the label.
Page 136 of 212
10PRACTICAL INFORMATION
122
Fitting a wheel
Position the wheel using the
centralising tool 5 to assist you.
Tighten the bolts by hand and
remove the centralising tool 5 .
Partly tighten the bolts using the
wheelbrace 1 .
Fold the jack 4 and remove it.
Fully tighten the bolts using the
wheelbrace 1 .
Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.
Put the corresponding tools in the
holder and secure its cover.
Place the holder on the ground
and align the spare wheel on it.
Pass the notched hook into the
holder cover.
R e i t t h e w h e e l u n d e r t h e v e h i c l e
tightening the winch control nut
using the wheelbrace 1 .
Fully tighten and check that
t h e w h e e l i s h o r i z o n t a l l y l u s h
a g a i n s t t h e r e a r l o o r .
C l o s e t h e l a p u s i n g t h e l u g t o
lock the winch.
Store the rest of the tools in the
right-hand trim of the boot.
F o r y o u r s a f e t y , a l w a y s
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- w i t h i r s t o r r e v e r s e g e a r e n g a g e d (position P for the automatic
gearbox),
- with the vehicle chocked.
N e v e r g o u n d e r n e a t h a v e h i c l e t h a t
i s s u p p o r t e d o n l y b y a j a c k ( u s e a
ramp).
N e v e r r e i t t h e h o l d e r u n d e r t h e
vehicle without the spare wheel.
D o n o t u s e a s c r e w d r i v e r i n p l a c e
o f t h e w h e e l b r a c e t o u n w i n d o r
w i n d t h e w i n c h . R e c o m m e n d a t i o n s w h e n u s i n g
t h e t e m p o r a r y s p a r e w h e e l *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, it must be replaced as
quickly as possible.
Observe the following instructions to
avoid altering the behaviour of the
vehicle:
-
do not exceed
50 mph (80 km/h) ,
- d o n o t i t a w h e e l t r i m ,
- drive with care,
- check the tyre pressure indicated
on the label.
A f t e r c h a n g i n g t h e w h e e l :
- have the correct positioning of the
punctured wheel, the tightening
of the bolts and the tyre pressure
checked by a PEUGEOT dealer
as soon as possible,
- have the punctured tyre repaired a n d r e i t i t t o t h e v e h i c l e a s s o o n
as possible,
- have the correct positioning of the spare wheel checked by a
PEUGEOT dealer.
W h e e l s i t t e d w i t h t h e T y r e U n d e r -
I n l a t i o n D e t e c t i o n s y s t e m
For further information refer to "Tyre
u n d e r - i n l a t i o n d e t e c t i o n " i n t h e
safety section.
* According to model and country.
Page 146 of 212
10PRACTICAL INFORMATION
131
* For fuse box 1 only.
** The maxi-fuses provide additional protection for the electrical systems. All work on the maxi-fuses must be carried out by
a PEUGEOT dealer.
Fuse N° Rating
Functions
F8 25 A Starter control.
F9 10 A Additional heating unit (Diesel), coolant level switch.
F10 30 A Engine control unit actuators (ignition coil, solenoid valves,
oxygen sensors, control units,
injectors, heaters), purge canister solenoid valve (1.4 litre petro l and 1.6 litre petrol).
F11 40 A Air conditioning blower.
F12 30 A Windscreen wipers low/high speed.
F13 40 A Built-in systems interface supply (ignition positive).
F14 30 A Air pump (2 litre petrol).
F 1 5 * 10 A Right main beam headlamp.
F 1 6 * 10 A Left main beam headlamp.
F 1 7 * 15 A Left dipped headlamp.
F 1 8 * 15 A Right dipped headlamp.
F41 15 A Six speed automatic gearbox control unit.
Page 148 of 212
10PRACTICAL INFORMATION
S p e c i a l f r o n t w i n d s c r e e n
wiper position
Within one minute of switching off
the ignition, operate the wipers
stalk to position the wiper blades
in the centre of the windscreen
(maintenance position).
C h a n g i n g a w i p e r b l a d e
Lift the wiper arm, then unclip the
blade and remove it.
Fit the new blade and push back
the arm.
Note: t h e s h o r t e s t b l a d e i s i t t e d o n
the vehicle’s right-hand windscreen
wiper arm.
T o r e t u r n t h e w i n d s c r e e n w i p e r s
t o t h e i r n o r m a l p o s i t i o n , s w i t c h o n
t h e i g n i t i o n a n d o p e r a t e t h e w i p e r
stalk.
BATTERY
T o c h a r g e t h e b a t t e r y u s i n g a
b a t t e r y c h a r g e r :
- Disconnect the battery starting
with the negative (-) terminal,
- Follow the instructions for use given by the battery charger
manufacturer,
- Check that the terminals and connectors are clean; if they are
covered with sulphate (white or
greenish deposit), disconnect
them and clean them,
- Reconnect the battery starting with the negative (-) terminal. Before disconnecting the
battery, you must wait for
2 minutes after switching off
the ignition.
Never disconnect a terminal when
the engine is running.
N e v e r c h a r g e a b a t t e r y w i t h o u t i r s t
disconnecting the terminals.
Close the windows and sunroof
before disconnecting the battery.
If they do not operate normally
following reconnection of the
battery, they must be reinitialised
(see sections "Reinitialisation of the
electric windows" and "Sunroof").
After every reconnection of the
battery, switch on the ignition and
wait 1 minute before starting to
allow the electronic systems to be
i n i t i a l i s e d . I f s l i g h t d i f i c u l t i e s a r e
experienced after this, please contact
a PEUGEOT dealer.
Following disconnection of the battery,
the remote control key and the GPS
satellite navigation system must
be reinitialised (see corresponding
section).
I t i s a d v i s a b l e t o d i s c o n n e c t t h e
b a t t e r y i f t h e v e h i c l e i s n o t t o b e
u s e d f o r a p e r i o d o f m o r e t h a n
one month.
T o s t a r t t h e v e h i c l e f r o m a n o t h e r
b a t t e r y :
- Connect the red cable to the positive (+) terminals of the two
batteries,
- Connect one end of the green or black cable to the negative (-)
terminal of the slave battery,
- Connect the other end of the green or black cable to an earth point on
the broken down vehicle as far as
possible from the battery,
-
Operate the starter, let the engine run,
- Wait for the engine to return to idle, then disconnect the cables. The batteries contain harmful
substances such as sulphuric
acid and lead. They must be
disposed of in accordance
with regulations and must never be
discarded with household waste.
Take used remote control and vehicle
batteries to an approved collection
point.
C H A N G I N G A W I N D S C R E E N
W I P E R B L A D E
Page 189 of 212
174
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
7
pqrs
0 #
ESC
MENU LIST
ESC
MENU LIST
ESC
MENU LIST
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
7
pqrs
0 #
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0
#
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0
#
1
2
3 1
2
06
TELEPHONE
INSTALLING YOUR SIM CARD ENTERING THE PIN CODE
Access the slot by pressing the button
using the tip of a pen.
Install the SIM card
in the holder and
then insert it in the
slot.
To remove the SIM card, repeat step 1.
Your SIM card must be installed and removed with th e RT4 GPS
audio/telephone switched off and the ignition off. Enter the PIN code on the keypad.
C o n i r m t h e P I N c o d e b y p r e s s i n g
button #.
PIN CODE
When entering your PIN code, tick the STORE PIN tab to gain
access to the telephone without having to enter thi s code when it is
used subsequently.
(NOT SUPPLIED)