2007.5 Peugeot 307 brake
[x] Cancel search: brakePage 128 of 212
CHECKS
116
CHECKS
Where the handbrake travel
is too great or there is a re-
duction in the performance
of the system, the hand-
brake should be adjusted,
even between services.
Have the system checked by a
PEUGEOT dealer.
Particle emission filter
(Diesel)
It is imperative that the particle emis-
s i o n i l t e r i s m a i n t a i n e d i n a c c o r d a n c e
with the manufacturer’s servicing
schedule, by a PEUGEOT dealer.
Note: following prolonged operation
of the vehicle at very low speed or at
idle, you may, in exceptional cases,
notice discharges of water vapour
at the exhaust on acceleration. This
has no effect on the behaviour of the
vehicle or on the environment. Brake pad wear depends
on the style of driving, in
particular for vehicles which
are used in town, over short
distances.
D i s c a n d d r u m w e a r s t a t u s
For any information relating to the wear
status of the surfaces of the discs and
drums, contact a PEUGEOT dealer
.
Only use products recom-
mended by PEUGEOT or
products of equivalent qual-
ity and characteristics.
To ensure best performance
from components as important as the
power steering and the braking sys-
tem, PEUGEOT selects and offers
q u i t e s p e c i i c p r o d u c t s .
To prevent damage to the electrical
units, high pressure washing to clean
the engine compartment is strictly
prohibited .
Oil filter
Used products
Avoid all prolonged contact of the
used oil with the skin.
B r a k e l u i d i s h a r m f u l t o h e a l t h a n d
very corrosive.
Air filter and passenger
compartment filter
Do not dispose of used oil,
b r a k e l u i d o r c o o l a n t i n t o
drains or onto the ground.
Empty the used oil into the
containers provided for this
purpose in the PEUGEOT network.
Battery
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Brake pads
It may be necessary to
check the thickness of the
pads, even between ser-
vices.
Handbrake
C h a n g e t h e i l t e r r e g u l a r l y ,
in accordance with the ser-
vicing schedule.
Manual gearbox
This does not require an oil
change. Have the level checked
in accordance with the manu-
facturer’s servicing schedule.
To check the main levels
a n d c e r t a i n c o m p o n e n t s ,
i n a c c o r d a n c e w i t h t h e
manufacturer’s servicing
s c h e d u l e , r e f e r t o t h e
pages of the servicing booklet
w h i c h c o r r e s p o n d t o y o u r v e h i -
cle’s engine.
H a v e t h e i l t e r e l e m e n t s r e -
placed regularly.
If you drive
i n d u s t y c o n d i t i o n s , c h a n g e
t h e m t w i c e a s o f t e n .
Page 129 of 212
CHECKS
116
CHECKS
Where the handbrake travel
is too great or there is a re-
duction in the performance
of the system, the hand-
brake should be adjusted,
even between services.
Have the system checked by a
PEUGEOT dealer.
Particle emission filter
(Diesel)
It is imperative that the particle emis-
s i o n i l t e r i s m a i n t a i n e d i n a c c o r d a n c e
with the manufacturer’s servicing
schedule, by a PEUGEOT dealer.
Note: following prolonged operation
of the vehicle at very low speed or at
idle, you may, in exceptional cases,
notice discharges of water vapour
at the exhaust on acceleration. This
has no effect on the behaviour of the
vehicle or on the environment. Brake pad wear depends
on the style of driving, in
particular for vehicles which
are used in town, over short
distances.
D i s c a n d d r u m w e a r s t a t u s
For any information relating to the wear
status of the surfaces of the discs and
drums, contact a PEUGEOT dealer
.
Only use products recom-
mended by PEUGEOT or
products of equivalent qual-
ity and characteristics.
To ensure best performance
from components as important as the
power steering and the braking sys-
tem, PEUGEOT selects and offers
q u i t e s p e c i i c p r o d u c t s .
To prevent damage to the electrical
units, high pressure washing to clean
the engine compartment is strictly
prohibited .
Oil filter
Used products
Avoid all prolonged contact of the
used oil with the skin.
B r a k e l u i d i s h a r m f u l t o h e a l t h a n d
very corrosive.
Air filter and passenger
compartment filter
Do not dispose of used oil,
b r a k e l u i d o r c o o l a n t i n t o
drains or onto the ground.
Empty the used oil into the
containers provided for this
purpose in the PEUGEOT network.
Battery
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Brake pads
It may be necessary to
check the thickness of the
pads, even between ser-
vices.
Handbrake
C h a n g e t h e i l t e r r e g u l a r l y ,
in accordance with the ser-
vicing schedule.
Manual gearbox
This does not require an oil
change. Have the level checked
in accordance with the manu-
facturer’s servicing schedule.
To check the main levels
a n d c e r t a i n c o m p o n e n t s ,
i n a c c o r d a n c e w i t h t h e
manufacturer’s servicing
s c h e d u l e , r e f e r t o t h e
pages of the servicing booklet
w h i c h c o r r e s p o n d t o y o u r v e h i -
cle’s engine.
H a v e t h e i l t e r e l e m e n t s r e -
placed regularly.
If you drive
i n d u s t y c o n d i t i o n s , c h a n g e
t h e m t w i c e a s o f t e n .
Page 130 of 212
10PRACTICAL INFORMATION
117
1. Wheelbrace.
2. Jack with handle.
3. Centralising tool.
4. Socket for anti-theft bolt.
5. Removable towing eye.
6. Alloy wheel bolt trim remover.
7.
Alloy wheel trim remover.
Parking the vehicle
If possible, park the vehicle on
level, stable and non-slippery
ground.
Apply the handbrake, switch off
t h e i g n i t i o n a n d e n g a g e i r s t o r
reverse gear (position P for the
automatic gearbox).
To gain access to the spare wheel
a n d t h e j a c k i n t h e b o o t , l i f t t h e l o o r
using the handle.
CHANGING A WHEEL (SALOON)
Tools
The following tools are located in a holder in the cent re of the spare wheel:
A diagram on the holder indicates the location of the to ols.
Page 132 of 212
10PRACTICAL INFORMATION
119
Putting the wheel back in place
Put the wheel back in place.
Unscrew the yellow central bolt a
few turns, then put it in place in
the centre of the wheel.
Tighten the central bolt fully until it
c l i c k s t o s e c u r e t h e w h e e l i r m l y .
Put the tool holder back in the
centre of the wheel and clip it.
P u t t h e b o o t l o o r b a c k i n p l a c e .
W h e e l s i t t e d w i t h t h e T y r e U n d e r -
I n l a t i o n D e t e c t i o n s y s t e m
For further information refer to "Tyre
u n d e r - i n l a t i o n d e t e c t i o n " i n t h e
safety section.
The wheel must be positioned
l a t , i n t h e c e n t r e o f i t s
housing.
F o r y o u r s a f e t y , a l w a y s
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- w i t h i r s t o r r e v e r s e g e a r e n g a g e d (position P for the automatic
gearbox),
- with the vehicle chocked.
N e v e r g o u n d e r n e a t h a v e h i c l e t h a t i s
s u p p o r t e d o n l y b y a j a c k ( u s e a r a m p ) .
* According to model and country. A f t e r c h a n g i n g t h e w h e e l :
- have the tightening of the bolts
and the tyre pressure checked by
a PEUGEOT dealer as soon as
possible,
- have the punctured tyre repaired a n d r e i t i t t o t h e v e h i c l e a s s o o n
as possible.
R e c o m m e n d a t i o n s w h e n u s i n g
t h e t e m p o r a r y s p a r e w h e e l *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, it must be replaced as
quickly as possible.
Observe the following instructions to
avoid altering the behaviour of the
vehicle:
-
do not exceed 50 mph (80 km/h) ,
- d o n o t i t a w h e e l t r i m ,
- drive with care,
- check the tyre pressure indicated
on the label.
Page 134 of 212
10PRACTICAL INFORMATION
120
Parking the vehicle
As far as possible, park the
vehicle on level, stable and non-
slippery ground.
Apply the handbrake, switch off
t h e i g n i t i o n a n d e n g a g e i r s t o r
reverse gear (position P for the
automatic gearbox). Access to the spare wheel
Open the boot.
O p e n t h e l a p u s i n g t h e l u g
to release the winch and gain
access to its control nut.
Unscrew the nut fully, using the
wheelbrace 1 , to unroll the winch
cable.
Tools
The following tools are located:
- in the right-hand trim of the boot,
1. Wheelbrace.
2. Removable towing eye.
3. Socket for anti-theft bolts.
- in the holder in the centre of the spare wheel,
4. Jack with handle.
5. Centralising tool.
6. Bolt cover tool.
CHANGING A WHEEL (ESTATE)
Page 136 of 212
10PRACTICAL INFORMATION
122
Fitting a wheel
Position the wheel using the
centralising tool 5 to assist you.
Tighten the bolts by hand and
remove the centralising tool 5 .
Partly tighten the bolts using the
wheelbrace 1 .
Fold the jack 4 and remove it.
Fully tighten the bolts using the
wheelbrace 1 .
Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.
Put the corresponding tools in the
holder and secure its cover.
Place the holder on the ground
and align the spare wheel on it.
Pass the notched hook into the
holder cover.
R e i t t h e w h e e l u n d e r t h e v e h i c l e
tightening the winch control nut
using the wheelbrace 1 .
Fully tighten and check that
t h e w h e e l i s h o r i z o n t a l l y l u s h
a g a i n s t t h e r e a r l o o r .
C l o s e t h e l a p u s i n g t h e l u g t o
lock the winch.
Store the rest of the tools in the
right-hand trim of the boot.
F o r y o u r s a f e t y , a l w a y s
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- w i t h i r s t o r r e v e r s e g e a r e n g a g e d (position P for the automatic
gearbox),
- with the vehicle chocked.
N e v e r g o u n d e r n e a t h a v e h i c l e t h a t
i s s u p p o r t e d o n l y b y a j a c k ( u s e a
ramp).
N e v e r r e i t t h e h o l d e r u n d e r t h e
vehicle without the spare wheel.
D o n o t u s e a s c r e w d r i v e r i n p l a c e
o f t h e w h e e l b r a c e t o u n w i n d o r
w i n d t h e w i n c h . R e c o m m e n d a t i o n s w h e n u s i n g
t h e t e m p o r a r y s p a r e w h e e l *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, it must be replaced as
quickly as possible.
Observe the following instructions to
avoid altering the behaviour of the
vehicle:
-
do not exceed
50 mph (80 km/h) ,
- d o n o t i t a w h e e l t r i m ,
- drive with care,
- check the tyre pressure indicated
on the label.
A f t e r c h a n g i n g t h e w h e e l :
- have the correct positioning of the
punctured wheel, the tightening
of the bolts and the tyre pressure
checked by a PEUGEOT dealer
as soon as possible,
- have the punctured tyre repaired a n d r e i t i t t o t h e v e h i c l e a s s o o n
as possible,
- have the correct positioning of the spare wheel checked by a
PEUGEOT dealer.
W h e e l s i t t e d w i t h t h e T y r e U n d e r -
I n l a t i o n D e t e c t i o n s y s t e m
For further information refer to "Tyre
u n d e r - i n l a t i o n d e t e c t i o n " i n t h e
safety section.
* According to model and country.
Page 140 of 212
10PRACTICAL INFORMATION
126
1. D i r e c t i o n i n d i c a t o r s ( P 2 1 W ) .
2. R e v e r s i n g l i g h t s ( P 2 1 W ) ,
l e f t - h a n d s i d e .
F o g l a m p ( P 2 1 W ) , r i g h t - h a n d
s i d e .
3. Brake lights (P 21 W).
4. S i d e l i g h t s ( x 2 ) ( R 5 W ) .
Using a 10 mm box spanner,
u n s c r e w t h e 2 i x i n g n u t s 1 .
Release the lamp unit by pushing
it outwards.
Squeeze the two tabs 2 to release
the bulb holder.
Change the faulty bulb.
W h e n r e i t t i n g , e n s u r e t h a t t h e
lamp unit seal has been put back
in place correctly.
These 6 bulbs are changed from
inside the boot:
Move aside the boot trim to
access the bulb holder,
Press the two tabs and remove
the bulb holder,
Change the faulty bulb.
W h e n r e i t t i n g , t a k e c a r e t o p a s s t h e
trim under the seal.
Rear lights (saloon) T h i r d b r a k e l i g h t ( s a l o o n )
(4 W 5 W bulbs)
Page 141 of 212
10PRACTICAL INFORMATION
127
Remove the tailgate upper trim
carefully by unclipping it on either
side, perpendicular to its direction
of engagement.
Insert a screwdriver into the two
outer holes B to press on the two
tabs C .
Push the light unit outwards while
maintaining the pressure on the
tabs.
Pull the light unit outwards while
tilting it.
Change the faulty bulb.
W h e n r e i t t i n g , e n s u r e t h a t t h e
light unit tabs are engaged
correctly and that the tailgate
upper trim has been put back in
place correctly.
1. Brake lights (P 21 W).
2. S i d e l i g h t s ( x 2 ) ( R 5 W ) .
3. D i r e c t i o n i n d i c a t o r s ( P 2 1 W ) .
4. R e v e r s i n g l i g h t ( P 2 1 W ) ,
l e f t - h a n d s i d e .
F o g l a m p ( P 2 1 W ) , r i g h t - h a n d
s i d e .
These 6 bulbs are changed by
removing the light:
Remove the corresponding boot
side trim to access the light,
R e m o v e t h e l i g h t i x i n g n u t i n s i d e
the boot,
R e m o v e t h e l i g h t i x i n g n u t o u t -
side the boot,
Remove the light,
Unclip the harness,
Remove the bulb holder pressing
on the tabs A ,
Change the faulty bulb.
Note: if necessary, use the wheel-
brace to remove the nuts.
W h e n r e i t t i n g , t a k e c a r e t o p o s i t i o n
the bulb holder and the light
correctly.
Number plate lights
(W 5 W)
Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Change the faulty bulb.
Rear lights (estate) T h i r d b r a k e l i g h t ( e s t a t e )
(4 W 5 W bulbs)