2007.5 Peugeot 307 service indicator
[x] Cancel search: service indicatorPage 27 of 212
INSTRUMENTS and CONTROLS
26
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
reset button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
t h e v e h i c l e a n d w a i t f o r a t l e a s t i v e
minutes, otherwise the zero re-set
will not be registered.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information.
Oil level correct
O i l l e v e l g a u g e f a u l t Flashing of " O I L - - "
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
T h e l e v e l r e a d w i l l o n l y b e c o r r e c t
i f t h e v e h i c l e i s o n l e v e l g r o u n d
a n d t h e e n g i n e h a s b e e n o f f f o r
m o r e t h a n 1 5 m i n u t e s .
Flashing of
"OIL" ,
linked with the
service warning
light, accompa-
nied by an audible
signal and a mes-
sage on the multifunction display, in-
dicates a lack of oil which could dam-
age the engine.
I f t h e l a c k o f o i l i s c o n i r m e d b y a
check using the dipstick, it is essen-
tial that the level is topped up.
L a c k o f o i l D i p s t i c k
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up t h e l e v e l v i a t h e o i l i l l e r
cap, using the type of
oil suited to your en-
gine.
A = max.
B = min.
S e r v i c e i n d i c a t o r z e r o r e - s e t
Page 67 of 212
ACCESS
64
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by any-
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi-
ble.
If the system does not function
correctly, the service warning light
comes on, accompanied by an audi-
ble signal and a message on the mul-
tifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
A heavy object attached to the key
(key ring, ...), weighing down on the
shaft of the key in the switch, may
cause a malfunction.
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y l a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible sig-
nal and a message on the multifunc-
tion display.
To replace the battery, unclip the cas-
ing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Key in ignition
A buzzer sounds on opening the driv-
er’s door, if the key has been left in
the ignition.
control battery or in the event of a re-
mote control malfunction, the remote
control must be reinitialised.
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few sec-
onds.
Switch off the ignition and remove
the remote control key from the
ignition lock.
The remote control is now working
again.
Locating your vehicle
Using the key
Turn the key in the lock on the
driver’s door to lock the vehicle.
T u r n t h e k e y a g a i n w i t h i n i v e
seconds to deadlock the vehicle.
E a c h a c t i o n i s c o n i r m e d b y i x e d
lighting of the direction indicators for
approximately two seconds.
When the vehicle is locked,
if unlocking is activated inad-
vertently without a door being
opened within 30 seconds,
the vehicle will lock automatically.
The folding and unfolding of the ex-
terior mirrors can be deactivated by
a PEUGEOT dealer.
To locate your vehicle, if
you have locked it, in a
car park:
press button B , the courtesy lights
come on and the direction indica-
t o r s l a s h f o r a f e w s e c o n d s .
Changing the remote control
battery
Reprogramming the remote
control
Following disconnection of the vehi-
cle’s battery, replacement of the remote
Page 69 of 212
ACCESS
64
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by any-
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi-
ble.
If the system does not function
correctly, the service warning light
comes on, accompanied by an audi-
ble signal and a message on the mul-
tifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
A heavy object attached to the key
(key ring, ...), weighing down on the
shaft of the key in the switch, may
cause a malfunction.
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y l a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible sig-
nal and a message on the multifunc-
tion display.
To replace the battery, unclip the cas-
ing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Key in ignition
A buzzer sounds on opening the driv-
er’s door, if the key has been left in
the ignition.
control battery or in the event of a re-
mote control malfunction, the remote
control must be reinitialised.
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few sec-
onds.
Switch off the ignition and remove
the remote control key from the
ignition lock.
The remote control is now working
again.
Locating your vehicle
Using the key
Turn the key in the lock on the
driver’s door to lock the vehicle.
T u r n t h e k e y a g a i n w i t h i n i v e
seconds to deadlock the vehicle.
E a c h a c t i o n i s c o n i r m e d b y i x e d
lighting of the direction indicators for
approximately two seconds.
When the vehicle is locked,
if unlocking is activated inad-
vertently without a door being
opened within 30 seconds,
the vehicle will lock automatically.
The folding and unfolding of the ex-
terior mirrors can be deactivated by
a PEUGEOT dealer.
To locate your vehicle, if
you have locked it, in a
car park:
press button B , the courtesy lights
come on and the direction indica-
t o r s l a s h f o r a f e w s e c o n d s .
Changing the remote control
battery
Reprogramming the remote
control
Following disconnection of the vehi-
cle’s battery, replacement of the remote
Page 82 of 212
VISIBILITY
74
A u t o m a t i c s w i t c h i n g o n o f t h e
lights
Side lights and dipped beam
headlamps switch on automatically if
the light is poor, or during operation of
the windscreen wipers. They switch
off as soon as the light becomes
bright enough or the windscreen
wipers stop.
Note: in foggy weather or in snow,
the brightness sensor can detect
s u f i c i e n t l i g h t . A s a c o n s e q u e n c e , t h e
lights will not come on automatically.
Deactivation
Turn ring A to a position other
than "AUTO" . Switching off is
accompanied by a message on
the multifunction display.
I f t h e b r i g h t n e s s s e n s o r d o e s n o t
f u n c t i o n c o r r e c t l y , the lights come
on accompanied by the service
warning light, an audible signal and
a message on the multifunction
display.
Contact a PEUGEOT dealer.
M a n u a l " F o l l o w - m e - h o m e "
lighting
W h e n t h e a u t o m a t i c s w i t c h i n g o n
o f t h e l i g h t s f u n c t i o n i s d e a c t i v a t e d ,
the side lights and dipped headlamps
remain on for the duration selected
for the automatic "follow-me-home"
lighting.
I f t h e v e h i c l e i s n o t i t t e d w i t h t h e
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
f u n c t i o n , when you leave your vehicle,
the side lights and dipped headlamps
remain on for thirty seconds.
D i r e c t i o n i n d i c a t o r s ( l a s h e r s )
L e f t : downwards.
Right: upwards.
Note: if you forget to cancel the
direction indicator, the volume of the
audible signal will increase, if you
are driving at a speed greater than
50 mph (80 km/h).
A u t o m a t i c " F o l l o w m e h o m e "
lighting
With the ignition off, when you leave
your vehicle with the automatic
s w i t c h i n g o n o f t h e l i g h t s f u n c t i o n
activated , the side lights and dipped
headlamps remain on for the selected
duration. Activation:
switch off the engine,
" l a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
" l a s h " t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
To deactivate or activate this
function, go to the multifunction
d i s p l a y c o n i g u r a t i o n m e n u .
The duration of the timed
period must also be set (15,
30, 60 seconds), via the multifunction
d i s p l a y c o n i g u r a t i o n m e n u , e x c e p t i n
the case of the monochrome screen
A for which it is pre-set.
C a n c e l l i n g :
" l a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it. Activation
Turn ring A to the "AUTO"
position. The automatic lighting
is accompanied by a message on
the multifunction display.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen, behind
the interior mirror. It is used for the
automatic switching on of the lights.
Page 83 of 212
VISIBILITY
74
A u t o m a t i c s w i t c h i n g o n o f t h e
lights
Side lights and dipped beam
headlamps switch on automatically if
the light is poor, or during operation of
the windscreen wipers. They switch
off as soon as the light becomes
bright enough or the windscreen
wipers stop.
Note: in foggy weather or in snow,
the brightness sensor can detect
s u f i c i e n t l i g h t . A s a c o n s e q u e n c e , t h e
lights will not come on automatically.
Deactivation
Turn ring A to a position other
than "AUTO" . Switching off is
accompanied by a message on
the multifunction display.
I f t h e b r i g h t n e s s s e n s o r d o e s n o t
f u n c t i o n c o r r e c t l y , the lights come
on accompanied by the service
warning light, an audible signal and
a message on the multifunction
display.
Contact a PEUGEOT dealer.
M a n u a l " F o l l o w - m e - h o m e "
lighting
W h e n t h e a u t o m a t i c s w i t c h i n g o n
o f t h e l i g h t s f u n c t i o n i s d e a c t i v a t e d ,
the side lights and dipped headlamps
remain on for the duration selected
for the automatic "follow-me-home"
lighting.
I f t h e v e h i c l e i s n o t i t t e d w i t h t h e
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
f u n c t i o n , when you leave your vehicle,
the side lights and dipped headlamps
remain on for thirty seconds.
D i r e c t i o n i n d i c a t o r s ( l a s h e r s )
L e f t : downwards.
Right: upwards.
Note: if you forget to cancel the
direction indicator, the volume of the
audible signal will increase, if you
are driving at a speed greater than
50 mph (80 km/h).
A u t o m a t i c " F o l l o w m e h o m e "
lighting
With the ignition off, when you leave
your vehicle with the automatic
s w i t c h i n g o n o f t h e l i g h t s f u n c t i o n
activated , the side lights and dipped
headlamps remain on for the selected
duration. Activation:
switch off the engine,
" l a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
" l a s h " t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
To deactivate or activate this
function, go to the multifunction
d i s p l a y c o n i g u r a t i o n m e n u .
The duration of the timed
period must also be set (15,
30, 60 seconds), via the multifunction
d i s p l a y c o n i g u r a t i o n m e n u , e x c e p t i n
the case of the monochrome screen
A for which it is pre-set.
C a n c e l l i n g :
" l a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it. Activation
Turn ring A to the "AUTO"
position. The automatic lighting
is accompanied by a message on
the multifunction display.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen, behind
the interior mirror. It is used for the
automatic switching on of the lights.