Page 130 of 212
10PRACTICAL INFORMATION
117
1. Wheelbrace.
2. Jack with handle.
3. Centralising tool.
4. Socket for anti-theft bolt.
5. Removable towing eye.
6. Alloy wheel bolt trim remover.
7.
Alloy wheel trim remover.
Parking the vehicle
If possible, park the vehicle on
level, stable and non-slippery
ground.
Apply the handbrake, switch off
t h e i g n i t i o n a n d e n g a g e i r s t o r
reverse gear (position P for the
automatic gearbox).
To gain access to the spare wheel
a n d t h e j a c k i n t h e b o o t , l i f t t h e l o o r
using the handle.
CHANGING A WHEEL (SALOON)
Tools
The following tools are located in a holder in the cent re of the spare wheel:
A diagram on the holder indicates the location of the to ols.
Page 132 of 212
10PRACTICAL INFORMATION
119
Putting the wheel back in place
Put the wheel back in place.
Unscrew the yellow central bolt a
few turns, then put it in place in
the centre of the wheel.
Tighten the central bolt fully until it
c l i c k s t o s e c u r e t h e w h e e l i r m l y .
Put the tool holder back in the
centre of the wheel and clip it.
P u t t h e b o o t l o o r b a c k i n p l a c e .
W h e e l s i t t e d w i t h t h e T y r e U n d e r -
I n l a t i o n D e t e c t i o n s y s t e m
For further information refer to "Tyre
u n d e r - i n l a t i o n d e t e c t i o n " i n t h e
safety section.
The wheel must be positioned
l a t , i n t h e c e n t r e o f i t s
housing.
F o r y o u r s a f e t y , a l w a y s
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- w i t h i r s t o r r e v e r s e g e a r e n g a g e d (position P for the automatic
gearbox),
- with the vehicle chocked.
N e v e r g o u n d e r n e a t h a v e h i c l e t h a t i s
s u p p o r t e d o n l y b y a j a c k ( u s e a r a m p ) .
* According to model and country. A f t e r c h a n g i n g t h e w h e e l :
- have the tightening of the bolts
and the tyre pressure checked by
a PEUGEOT dealer as soon as
possible,
- have the punctured tyre repaired a n d r e i t i t t o t h e v e h i c l e a s s o o n
as possible.
R e c o m m e n d a t i o n s w h e n u s i n g
t h e t e m p o r a r y s p a r e w h e e l *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, it must be replaced as
quickly as possible.
Observe the following instructions to
avoid altering the behaviour of the
vehicle:
-
do not exceed 50 mph (80 km/h) ,
- d o n o t i t a w h e e l t r i m ,
- drive with care,
- check the tyre pressure indicated
on the label.
Page 134 of 212
10PRACTICAL INFORMATION
120
Parking the vehicle
As far as possible, park the
vehicle on level, stable and non-
slippery ground.
Apply the handbrake, switch off
t h e i g n i t i o n a n d e n g a g e i r s t o r
reverse gear (position P for the
automatic gearbox). Access to the spare wheel
Open the boot.
O p e n t h e l a p u s i n g t h e l u g
to release the winch and gain
access to its control nut.
Unscrew the nut fully, using the
wheelbrace 1 , to unroll the winch
cable.
Tools
The following tools are located:
- in the right-hand trim of the boot,
1. Wheelbrace.
2. Removable towing eye.
3. Socket for anti-theft bolts.
- in the holder in the centre of the spare wheel,
4. Jack with handle.
5. Centralising tool.
6. Bolt cover tool.
CHANGING A WHEEL (ESTATE)
Page 136 of 212
10PRACTICAL INFORMATION
122
Fitting a wheel
Position the wheel using the
centralising tool 5 to assist you.
Tighten the bolts by hand and
remove the centralising tool 5 .
Partly tighten the bolts using the
wheelbrace 1 .
Fold the jack 4 and remove it.
Fully tighten the bolts using the
wheelbrace 1 .
Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.
Put the corresponding tools in the
holder and secure its cover.
Place the holder on the ground
and align the spare wheel on it.
Pass the notched hook into the
holder cover.
R e i t t h e w h e e l u n d e r t h e v e h i c l e
tightening the winch control nut
using the wheelbrace 1 .
Fully tighten and check that
t h e w h e e l i s h o r i z o n t a l l y l u s h
a g a i n s t t h e r e a r l o o r .
C l o s e t h e l a p u s i n g t h e l u g t o
lock the winch.
Store the rest of the tools in the
right-hand trim of the boot.
F o r y o u r s a f e t y , a l w a y s
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- w i t h i r s t o r r e v e r s e g e a r e n g a g e d (position P for the automatic
gearbox),
- with the vehicle chocked.
N e v e r g o u n d e r n e a t h a v e h i c l e t h a t
i s s u p p o r t e d o n l y b y a j a c k ( u s e a
ramp).
N e v e r r e i t t h e h o l d e r u n d e r t h e
vehicle without the spare wheel.
D o n o t u s e a s c r e w d r i v e r i n p l a c e
o f t h e w h e e l b r a c e t o u n w i n d o r
w i n d t h e w i n c h . R e c o m m e n d a t i o n s w h e n u s i n g
t h e t e m p o r a r y s p a r e w h e e l *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, it must be replaced as
quickly as possible.
Observe the following instructions to
avoid altering the behaviour of the
vehicle:
-
do not exceed
50 mph (80 km/h) ,
- d o n o t i t a w h e e l t r i m ,
- drive with care,
- check the tyre pressure indicated
on the label.
A f t e r c h a n g i n g t h e w h e e l :
- have the correct positioning of the
punctured wheel, the tightening
of the bolts and the tyre pressure
checked by a PEUGEOT dealer
as soon as possible,
- have the punctured tyre repaired a n d r e i t i t t o t h e v e h i c l e a s s o o n
as possible,
- have the correct positioning of the spare wheel checked by a
PEUGEOT dealer.
W h e e l s i t t e d w i t h t h e T y r e U n d e r -
I n l a t i o n D e t e c t i o n s y s t e m
For further information refer to "Tyre
u n d e r - i n l a t i o n d e t e c t i o n " i n t h e
safety section.
* According to model and country.
