2006 YAMAHA YFZ450 oil

8-10
NOTE:
8Recommended brake fluid: DOT 4
8Brake fluid replacement:
9When disassembling the master cylinder or caliper cylinder, replace the brake fluid. Normally
check the brake fluid level and add the fluid as required.
9On the inner parts of the master cylinder and caliper cylinder, replace the oil seals every two
years.
9Replace the brake hoses every four years, or if cracked or damaged.
5TG-9-62 8 5/13/05 1:48 PM Page 8-10

8-25
EBU13932
Engine oil and oil filter element
The engine oil level should be checked before
each ride. In addition, the oil must be changed
and the oil filter element replaced at the intervals
specified in the periodic maintenance and lubri-
cation chart.
To check the engine oil level
1. Place the ATV on a level surface.
2. Start the engine, warm it up until the
engine oil has reached a normal tempera-
ture of 40 ° C, let it continue to idle for ten
seconds or more, and then turn the engine
off.
NOTE:
To achieve the proper engine oil temperature for
an accurate oil level reading, the engine must
have first completely cooled down, and then
warmed up again for several minutes to normal
operating temperature.
5TG-9-62 8 5/13/05 1:48 PM Page 8-25

8-27
3. Remove the engine oil tank filler cap, wipe
the dipstick clean with a clean rag, insert it
back into the filler hole (without screwing it
in), and then remove it again to check the
oil level.
NOTE:
The engine oil should be between the minimum
and maximum level marks.
4. If the engine oil is below the minimum level
mark, add sufficient oil of the recommend-
ed type through the engine oil tank filler
hole to raise it to the correct level.
NOTE:
When adding oil, be careful not to overfill the
engine oil tank; the oil level rises faster starting
from the half-level-portion on the dipstick.
5. Insert the dipstick into the engine oil tank
filler hole, and then tighten the engine oil
tank filler cap.
1. Engine oil tank 2. Engine oil tank filler cap
3. Dipstick 4. Maximum level mark
5. Minimum level mark 6. Engine oil filler cap
1. Réservoir d’huile de moteur
2. Bouchon de remplissage de l’huile de moteur
3. Jauge
4. Repère de niveau maximum
5. Repère de niveau minimum
6. Bouchon de remplissage d’huile de moteur
1. Depósito de aceite de motor
2. Tapa de relleno del depósito de aceite de motor
3. Varilla de medición
4. Marca de nivel máximo
5. Marca de nivel mínimo
6. Tapa del filtro de aceite de motor
5TG-9-62 8 5/13/05 1:48 PM Page 8-27

8-29
cC
Make sure that the engine oil tank filler cap
is securely tightened, otherwise oil may seep
out when the engine is running.
To change the engine oil (with or without oil
filter element replacement)
1. Remove the engine guard by removing the
bolts.
2. Start the engine, warm it up for several
minutes, and then turn it off.
3. Place an oil pan under the engine to collect
the used oil.
1. Engine guard 2. Bolt (×6)1. Protège-carter2. Boulon (×6)1. Protector del motor
2. Perno (×6)
5TG-9-62 8 5/13/05 1:48 PM Page 8-29

8-31
4. Remove the engine oil filler cap and the
crankcase engine oil drain bolt.
5. Remove the engine oil tank filler cap and
the engine oil tank drain bolt.
6. Check the washers for damage, and
replace if necessary.
1. Crankcase engine oil drain bolt1. Boulon de vidange d’huile du carter1. Perno de drenaje de aceite de motor del cárter
1. Engine oil tank drain bolt
1. Boulon de vidange du réservoir d’huile1. Perno de drenaje del depósito aceite de motor
5TG-9-62 8 5/13/05 1:48 PM Page 8-31

8-33
NOTE:
Skip steps 7–10 if the oil filter element is not
being replaced.
7. Remove the oil filter element cover by
removing the bolts, and then remove the
oil filter element.
8. Check the O-rings for damage, and
replace them if necessary.
9. Install a new oil filter element and the O-
rings.
NOTE:
Make sure that the O-rings are properly seated.
10. Install the oil filter element cover by
installing the bolts, and then tighten them
to the specified torque.1. Oil filter element 2. O-ring (×2)1. Élément du filtre à huile 2. Joint torique (×2)1. Filtro de aceite 2. Junta torica (×2) 1. Oil filter element cover 2. Bolt (×3)
1. Couvercle de l’élément du filtre à huile
2. Boulon (×3)
1. Cubierta del elemento del filtro de aceite
2. Perno (×3)
5TG-9-62 8 5/13/05 1:48 PM Page 8-33

8-35
11. Install the crankcase engine oil drain bolt
and the engine oil tank drain bolt, and then
tighten them to the specified torques.
12. Pour the specified amount of recommend-
ed engine oil through the engine oil tank
filler hole, insert the dipstick, and then
tighten the engine oil tank filler cap.
13. Pour the specified amount of recommend-
ed engine oil through the engine oil filler
hole, and then install and tighten the
engine oil filler cap.
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m0kgf)
Tightening torques:
Crankcase engine oil drain bolt:
20 Nm (2.0 m0kgf)
Engine oil tank drain bolt:
19 Nm (1.9 m0kgf)
5TG-9-62 8 5/13/05 1:48 PM Page 8-35

8-37
Recommended engine oil:
See page 10-2.
Oil quantity:
Without oil filter element replacement:
Quantity in oil tank:
1.55 L
Quantity in crankcase:
0.20 L
Total amount:
1.75 L
With oil filter element replacement:
Quantity in oil tank:
1.55 L
Quantity in crankcase:
0.30 L
Total amount:
1.85 L
5TG-9-62 8 5/13/05 1:48 PM Page 8-37