Page 17 of 82
moving, otherwise the electrical
systems will be switched off, which
may result in loss of control or an
accident. Make sure that the vehi-
cle is stopped before turning the
key to “OFF” or “LOCK”.EAU33461
Indicators, indicator lights
and warning light
1. Fuel level warning light “x”
2. High beam indicator light “j”
3. Left turn signal indicator light “c”
4. Immobilizer system indicator light “”5. Right turn signal indicator light “d”
EAU11030
Turn signal indicator lights “c” and
“
d”
The corresponding indicator light flas-
hes when the turn signal switch is
pushed to the left or right.
EAU11080
High beam indicator light “j”
This indicator light comes on when
the high beam of the headlight is swit-
ched on.
EAU11350
Fuel level warning light “ ”
This warning light comes on when the
fuel level drops below approximately
2 L (0.53 US gal) (0.44 Imp gal). When
this occurs, refuel as soon as possi-
ble.
The electrical circuit of the warning
light can be checked by turning the
key to “ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical
circuit.
EAU27020
Immobilizer system indicator light
“”
The electrical circuit of the indicator
light can be checked by turning the
key to “ON”.
If the indicator light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical
circuit.
When the key is turned to “OFF” and
30 seconds have passed, the indica-
tor light will start flashing indicating
the immobilizer system is enabled.
After 24 hours have passed, the indi-
c
dj
y
x12345
3
INSTRUMENT AND CONTROL FUNCTIONS
3-3
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-3
Page 18 of 82
cator light will stop flashing, however
the immobilizer system is still ena-
bled.
NOTE:
This model is also equipped with a
self-diagnosis device for the immobi-
lizer system. If the immobilizer system
is defective, the indicator light will
start flashing a pattern when the key
is turned to “ON”. When this occurs,
have a Yamaha dealer check the self-
diagnosis system. However, if the
indicator light slowly flashes five
times, and then quickly flashes two
times repeatedly, this error could be
caused by signal interference. If this
occurs, try the following.
1. Use the code re-registering key
to start the engine.
NOTE:
Make sure there are no other immobi-
lizer keys close to the main switch,
and do not keep more than one
immobilizer key on the same key ring!
Immobilizer system keys may cause
signal interference, which may pre-
vent the engine from starting.
2. If the engine starts, turn it off, and
try starting the engine with the
standard keys.
3. If one or both of the standard
keys do not start the engine, take
the vehicle, the code re-registe-
ring key and both standard keys
to a Yamaha dealer and have the
standard keys re-registered.
EAU12110
Fuel gauge
1. Fuel gauge
2. Fuel level warning light “x”
The fuel gauge indicates the amount
of fuel in the fuel tank. The needle
moves towards “E” (Empty) as the
fuel level decreases. When the needle
reaches “E”, approximately 2 L (0.53
US gal) (0.44 Imp gal) of fuel remain in
the fuel tank. If this occurs, refuel as
soon as possible.
cj
x
12
3
INSTRUMENT AND CONTROL FUNCTIONS
3-4
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-4
Page 19 of 82
NOTE:
Do not allow the fuel tank to empty
itself completely.EAU12171
Coolant temperature gauge
1. Red zone
2. Temperature gauge
With the key in the “ON” position, the
coolant temperature gauge indicates
the temperature of the coolant. The
coolant temperature varies with chan-
ges in the weather and engine load. If
the needle reaches or enters the red
zone, stop the vehicle and let the
engine cool. (See page 6-30.)
ECA10020
CAUTION:
Do not operate the engine if it is
overheated.
EAUS1340
Speedometer
1. Speedometer
2. Red zone
The speedometer shows the riding
speed.
ECAS0010
CAUTION:
Do not operate the scooter in the
speedometer red zone.Red zone:
150 km/h (93 mph) and above
c
dj
x
1
2
d
y
1
2
3
INSTRUMENT AND CONTROL FUNCTIONS
3-5
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-5
Page 20 of 82
EAUM1480
Multi-function display
1. “MODE” button
2. Multi-function display
3. “SET” button
The multi-function display is equip-
ped with the following:
an odometer (which shows the
total distance traveled)
two tripmeters (which show the
distance traveled since they were
last set to zero, the time passed
since the tripmeters were set to
zero, and the average speed tra-
veled during this time)
a fuel reserve tripmeter (which
shows the distance traveled sin-
ce the fuel level warning light
came on)
a clock
an ambient temperature display
a service indicator (which is dis-
played when periodic maintenan-
ce and lubrication is necessary)
NOTE:
For the UK, the distance traveled
is displayed in miles and the tem-
perature reading is displayed in
°F.
For other countries, the distance
traveled is displayed in kilome-
ters and the temperature reading
is displayed in °C.
1. Total
2. Trip 1
2. Trip 2
4. Trip/Fuel
Odometer and tripmeter modes
Pushing the “MODE” button switches
the display between the odometer
mode “Total” and the tripmeter
modes “Trip” in the following order:
Total
Trip 1 Trip 2 Trip/fuel
Total
1. Distance
2. Time
3. Average speed
NOTE:
The Trip/fuel odometer is only
activated if the fuel level warning
light comes on.
The Trip 2 odometer is automati-
cally reset after turning the key to
“OFF”.
c
dj
x
1
23
3
INSTRUMENT AND CONTROL FUNCTIONS
3-6
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-6
Page 21 of 82
Pushing the “SET” button when in the
tripmeter mode switches the display
between the different tripmeter func-
tions in the following order:
Distance
Time Average speed
Distance
If the fuel level warning light comes on
(See page 3-3.), the display will auto-
matically change to the fuel reserve
tripmeter mode “Trip/fuel” and start
counting the distance traveled from
that point. In that case, pushing the
“SET” button switches the display
between the various tripmeter and
odometer modes in the following
order:
Trip/Fuel
Trip 1 Trip 2 Total
Trip/fuelTo reset a tripmeter, select it by pus-
hing the “MODE” button, and then
push the “SET” button for at least one
second. If you do not reset the fuel
reserve tripmeter manually, it will
reset itself automatically and the dis-
play will return to the prior mode after
refueling and traveling 5 km.
Clock mode
To set the clock:
1. When the display is in the “Total”
mode, push the “SET” button for
at least two seconds.
2. When the hour digits start flas-
hing, push the “SET” button to
set the hours.3. Push the “MODE” button, and
the minute digits will start flas-
hing.
4. Push the “SET” button to set the
minutes.
5. Push the “MODE” button and
then release it to start the clock.
The display will return to the
“Total” mode.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-7
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-7
Page 22 of 82
Ambient temperature display
1. Frost warning indicator“”2. Negative symbol “–”
3. Ambient temperature
This display shows the ambient tem-
perature from-30°C to 50°C.
The frost warning indicator“”
automatically comes on if the tempe-
rature is lower than 3°C
Service indicator
1. Service indicator
When periodic maintenance and
lubrication is necessary (See page 6-
3.), “Service” will appear in the dis-
play until the Service indicator reset is
made.
T
o reset the service indicator:
1. Turn the key to “ON”.
2. Hold the “MODE” and “SET” but-
ton pushed for two to five
seconds.
3. Release the buttons, and the ser-
vice indicator will go off.
NOTE:
The service indicator will come
on at the initial 1000 km and
every 3000 km thereafter.
If periodic maintenance and
lubrication is performed before
the service indicator comes on,
the indicator must be reset as
soon as possible so that it comes
for the next periodic maintenance
and lubrication interval.
EAU12331
Anti-theft alarm (optional)
This motorcycle can be equipped
with an optional anti-theft alarm by a
Yamaha dealer. Contact a Yamaha
dealer for more information.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-8
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-8
Page 23 of 82
EAU12344
Handlebar switches
1. Dimmer switch “jk”
2. Pass switch "PASSING"
3. Turn signal switch “cd”
4. Horn switch “a”
1. Starting switch “g”
2. Hazard switch“”
EAUS1300
Pass switch “PASSING”
Press this switch to flash the head-
light.
EAUS1020
Dimmer switch “j/k”
Set this switch to “
j” for the high
beam and to “
k” for the low beam.
With the headlight on low beam,
press this switch downwards to flash
the headlight.
EAU12460
Turn signal switch “c/d”
To signal a right-hand turn, push this
switch to “
d”. To signal a left-hand
turn, push this switch to “
c”. When
released, the switch returns to the
center position. To cancel the turn
signal lights, push the switch in after it
has returned to the center position.
EAU12500
Horn switch “a”
Press this switch to sound the horn.
EAU12720
Start switch “g”
With the sidestand up, push this
switch while applying the front or rearbrake to crank the engine with the
starter.
ECA10050
CAUTION:
See page 5-1 for starting instruc-
tions prior to starting the engine.
EAUM1990
Hazard switch “ ”, “h”
With the key in the “ON” position, set
this switch to “ ” to turn on the
hazard lighting (simultaneous flashing
of all turn signal lights). To turn off the
hazard lighting, set this switch to “h”
and, then turn the key to “OFF”.
NOTE:
Even if the key is turned from “ON” to
“OFF” with the hazard lighting on, the
hazard lighting will continue to flash
regardless of the hazard switch posi-
tion. To cancel the hazard lighting, the
key must be turned to “ON” and the
hazard switch must be set to the “h”
position.
12
1
2
3
4
3
INSTRUMENT AND CONTROL FUNCTIONS
3-9
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-9
Page 24 of 82
The hazard lighting is used in case of
an emergency or to warn other drivers
when your scooter is stopped where
it might be a traffic hazard.
ECA10060
CAUTION:
Do not use the hazard light for an
extended length of time, otherwise
the battery may discharge.
EAU12900
Front brake lever
1. Front brake lever
The front brake lever is located on the
right handlebar grip. To apply the
front brake, pull this lever toward the
handlebar grip.
EAU12950
Rear brake lever
1. Rear brake lever
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the hand-
lebar grip.
11
3
INSTRUMENT AND CONTROL FUNCTIONS
3-10
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-10
