2006 YAMAHA VX CRUISER cooling

E
2
EJU10070
FEATURES AND
FUNCTIONS
Location of main components .............. 2-1
Operation of controls and other
functions ................................................... 2-5
Seat ........................................................ 2-5
Hood ....................................................... 2-6
Fuel tank filler cap .................................. 2-6
Remote control transmitter
(for VX110 Deluxe) ................................ 2-7
Engine stop switch ................................. 2-9
Engine shut-off switch ............................ 2-9
Start switch ........................................... 2-10
Throttle lever ........................................ 2-10
Cooling water pilot outlet ..................... 2-11
Steering system ................................... 2-12
Shift lever (for VX110 Deluxe) ............. 2-13
Handgrip ............................................... 2-14
Yamaha Engine Management System
(YEMS) ................................................. 2-15
Yamaha Security System/Low-RPM
mode (for VX110 Deluxe) .................... 2-15
Multifunction meter ............................... 2-18
Storage compartments ........................ 2-24
E_F1K-70.book Page 1 Thursday, October 20, 2005 1:30 PM

2-1
E
EJU10080
Location of main components
1Handlebars
Use to control direction.
2Seat
3Footwell
Use to place feet for balance.
To keep proper balance while facing to the rear
to watch the skier.
4Sponsons
5Gunwale
6Cooling water pilot outlet
Use to verify cooling water flow.
7Fuel tank filler cap
8Bow eye
Use to attach rope for transporting, mooring or
towing the watercraft in an emergency.
9Hood
E_F1K-70.book Page 1 Thursday, October 20, 2005 1:30 PM

2-4
E
1Air filter case
2Water separator
3Fuel tank
4Battery
5Flush hose connector
Use to flush the engine cooling water pas-
sages.
6Electrical box
Protects electrical components from water.
7Oil tank8Muffler
9Spark plugs/Spark plug caps/Ignition coils
E_F1K-70.book Page 4 Thursday, October 20, 2005 1:30 PM

2-11
E
EJU11301
Cooling water pilot outlet
This watercraft is equipped with a cooling
water pilot outlet.
When the engine is running, cooling
water is circulated in the engine, and then it
is discharged from the pilot outlet.
To check for proper operation of the cool-
ing system, check that water is being dis-
charged from the pilot outlet. If water is not
being discharged from the outlet, cooling
water may not be circulating in the engine.
When this occurs, stop the engine and
check for the cause. (See pages 2-22 and
5-3 for more information.)
NOTE:@
If the cooling water passages are dry, it
will take about 60 seconds for the water to
reach the outlet after the engine is
started.

Water discharge may not be constant at
idle, therefore, open the throttle a little to
check that water discharges properly.
@
E_F1K-70.book Page 11 Thursday, October 20, 2005 1:30 PM

2-22
E
EJU21183
Engine overheat warning indicator
This model is equipped with an engine
overheat warning system.
If the engine starts to overheat, the warn-
ing light and the overheat warning indicator
blink, and then come on. The buzzer also
begins to sound intermittently, and then it
sounds continuously. After the light and indi-
cator start to blink and the buzzer sounds,
the engine speed is limited to help prevent
damage.
If this occurs, immediately reduce the
engine speed, return to shore, and then
check for water discharge at the port (left)
cooling water pilot outlet. If there is no dis-
charge of water, check the intake grate and
impeller for clogging.
WARNING@ Before attempting to remove weeds or
debris from the intake grate or impeller,
shut the engine off and remove the clip
from the engine shut-off switch. Severe
injury or death could result from coming
in contact with the rotating parts of the
jet pump.
@
CAUTION:@ If you cannot locate and correct the
cause of the overheating, consult a
Yamaha dealer. Continuing to operate at
higher speeds could result in severe
engine damage.
@
NOTE:@ Press the select button 1 on the multifunc-
tion meter to stop the buzzer.
@
E_F1K-70.book Page 22 Thursday, October 20, 2005 1:30 PM

3-5
E
EJU13460
Pre-operation checks
EJU13470
Pre-operation check list
Before operating this watercraft, perform the checks in the following check list. See the
accompanying text in this chapter for details on how to perform the checks.
WARNING@ If any item in the pre-operation check list is not working properly, have it inspected
and repaired before operating the watercraft, otherwise an accident could occur.
@
NOTE:@ Pre-operation checks should be made thoroughly each time the watercraft is used. This pro-
cedure can be completed in a short time. It is worth the time spent to assure safety and reli-
ability.
@
ITEM ROUTINE PAGE
Engine compartment Remove the seat to ventilate the engine compartment.
Check for fuel vapors and loose electrical connections.3-6
Bilge Check for water and fuel and remove if necessary. 3-9
Stern drain plugs Check for proper installation. 3-9
Throttle lever Check that the throttle lever springs back smoothly. 3-11
Steering system Check for proper operation. 3-12
Shift lever and reverse gate
(VX110 Deluxe)Check for proper operation.
3-12
Fuel and oil Check fuel and oil levels and add if necessary.
Check the hoses and tanks for leakage.3-6, 3-7
Water separator Check for water and drain if necessary. 3-8
Battery Check electrolyte level, battery terminal connections,
breather hose connection, and battery condition.3-10
Hood Check that the hood is properly secured. 2-6
Seat Check that the seat is properly secured. 2-5
Hull and deck Check the hull and deck for cracks or other damage. 3-6
Jet unit Check for debris and remove if necessary. 3-13
Fire extinguisher Check condition and replace if necessary. 3-11
Engine shut-off cord Check condition and replace if frayed or broken. 3-13
Switches Check the start switch, engine stop switch, and engine
shut-off switch for proper operation.3-14
Cooling water pilot outlet Check that water is discharged while the engine is run-
ning and the watercraft is in the water.3-14
Multifunction meter Check for warning indications and proper operation. 3-14
E_F1K-70.book Page 5 Thursday, October 20, 2005 1:30 PM

3-7
E
EJU21230
Engine oil level
Check the engine oil level before each
use.
CAUTION:@
When checking the engine oil level on
water, be careful of other watercraft,
boats, swimmers, and obstacles. The
water current and wind can cause the
watercraft to move and lead to a colli-
sion.

When checking the engine oil level on
land, supply water to the cooling water
passages. (See page 4-1 for proce-
dures on supplying water.)

Make sure that the engine has enough
oil but do not overfill it. If there is too
little oil, the engine can be damaged. If
there is too much oil, the air filter can
become saturated with oil, perma-
nently damaging the filter and reduc-
ing engine performance. Follow the
checking procedure carefully.

Make sure that debris and water do not
enter the oil tank filler hole. Debris and
water in the engine oil can cause seri-
ous engine damage.
@
To check the engine oil level:
1. Place the watercraft in a horizontal posi-
tion or launch the watercraft, and then
start the engine.
2. Run the engine at trolling speed for
6 minutes or more, and then stop the
engine.
NOTE:@ If the ambient temperature is 20 °C (68°F)
or less, warm up the engine for an additional
5 minutes.
@
3. Remove the seat. (See page 2-5 for seat
removal and installation procedures.)
E_F1K-70.book Page 7 Thursday, October 20, 2005 1:30 PM

3-13
E
EJU10580
Jet unit
Carefully check the jet intake for weeds,
debris, or anything else that might restrict
the intake of water. If the intake is clogged,
cavitation could occur, reducing jet thrust,
and possibly damaging the jet pump.
In some cases, the engine may overheat
because of lack of cooling water, and dam-
age to the engine could result. Engine cool-
ing water is fed to the engine by the jet
pump. (See page 5-3 for jet intake cleaning
procedures.)
WARNING@
Keep away from intake grate while
engine is on. Items such as long hair,
loose clothing, or PFD straps can
become entangled in moving parts
resulting in severe injury or drowning.

Stop the engine and remove the clip
from the engine shut-off switch before
removing any debris or weeds, which
may have collected around the jet
intake.
@
EJU10590
Engine shut-off cord (lanyard)
Check that the engine shut-off cord is not
frayed or broken. If the cord is damaged,
replace it; never try to repair it or tie it
together.
E_F1K-70.book Page 13 Thursday, October 20, 2005 1:30 PM