2006 YAMAHA TTR50 engine

4 - 54
ENGSHIFT FORK, SHIFT CAM AND TRANSMISSION
SHIFT FORK, SHIFT CAM AND TRANSMISSION
0.8~1.3mm
(0.03~0.05 in)
New
New
New
New
M
M
12 13 14
15 16
17 18
19
7
8
9
10
11
4 3
1
2
M
E
5 6
Extent of removal:
1 Shift fork, shift cam, main axle and drive axle removal
2 Main axle disassembly
3 Drive axle disassembly
Extent of removal Order Part name Q ’ty Remarks
SHIFT FORK, SHIFT CAM AND
TRANSMISSION REMOVAL
Preparation for removal Engine assembly Separate the crankcase. Refer to “CRANKCASE AND CRANK-
SHAFT ”section.
1 Guide bar 1
2Shift cam 1
Refer to “REMOVAL POINTS ”.
3 Shift fork 1
“L ” 1
4 Shift fork 2 “R ” 1
5 Main axle assembly 1
6 Drive axle assembly 1
7 2nd pinion gear 1
8 Circlip 1
9 Washer 1
2
1

4 - 57
ENGSHIFT FORK, SHIFT CAM AND TRANSMISSION
2. Install:Main axle assembly 1
 Drive axle assembly 2
 Shift fork 2 “R ” 3
 Shift fork 1 “L ” 4
 Shift cam 5
 Guide bar 6
NOTE:
The embossed marks on the shift forks
should face towards the right side of the
engine and be in the following sequence:
“R ”, “L ”.
 Mesh the shift fork 2 “R ” with the 3rd wheel
gear on the drive axle.
 Mesh the shift fork 1 “L ” with the 2nd pinion
gear on the main axle.
3. Check: Shifter operation
 Transmission operation
Unsmooth operation → Repair.
3
4
5 1
6
2

5 - 1
CHAS
EC500000
CHASSIS
FRONT WHEEL AND REAR WHEEL
FRONT WHEEL AND FRONT BRAKE
Extent of removal:1 Front wheel removal
2 Wheel bearing removal
3 Brake shoe plate assembly removal and disassembly
Extent of removal Order Part name Q ’ty Remarks
FRONT WHEEL REMOVAL
WARNING
Support the machine securely so
there is no danger of it falling over.
Preparation for removal Hold the machine by placing the
suitable stand under the engine.
1 Front brake adjuster 1
2Pin 1
3Spring 1
4 Locknut 1
5 Brake cable 1 Disconnect at the lever side.
6 Front fork guard (left) 1
7 Front fork guard (right) 1
8 Wheel axle nut 1
9 Front wheel axle 1
21
FRONT WHEEL AND REAR WHEEL

5 - 3
CHASFRONT WHEEL AND REAR WHEEL
REAR WHEEL AND REAR BRAKE
Extent of removal:1 Rear wheel removal
2 Wheel bearing removal
3 Brake shoe plate assembly removal and disassembly
Extent of removal Order Part name Q ’ty Remarks
REAR WHEEL REMOVAL
WARNING
Support the machine securely so
there is no danger of it falling over.
Preparation for removal Hold the machine by placing the
suitable stand under the engine.
1 Rear brake adjuster 1
2Pin 1
3Spring 1
4 Drive chain locknut 2
5 Wheel axle nut 1
6 Rear wheel axle 1
7 Drive chain puller 2
8 Rear wheel 1
9 Collar (left) 1
10 Brake shoe plate assembly 1
2
1
3

5 - 10
CHASHANDLEBAR
HANDLEBAR
Extent of removal: 1 Handlebar removal
Extent of removal Order Part name Q ’ty Remarks
HANDLEBAR REMOVAL
1Brake lever 1
2 Brake cable 1 Disconnect at the lever side.
3 Start switch 1
4 Throttle cable 1 Disconnect at the throttle side.
5 Right grip 1
6 Tube guide 1
7 Engine stop switch 1
8Left grip 1
9Starter lever 1
10 Handlebar 1
11 Main switch 1
1

5 - 12
CHAS
3. Install:Engine stop switch 1
NOTE:
Align the tab a on the engine stop switch
holder with the hole b in the handlebar.
a
b
1
4. Install:
Start switch 1
NOTE:
Align the mating surfaces a of the start switch
with the punch mark b on the handlebar.
1
b a
5. Install:
Throttle cable 1
NOTE:
After installing the throttle cable, insert the rub-
ber seal and throttle cable guide completely
into the hole in the start switch housing, mak-
ing sure that the rubber seal flange a, throttle
cable guide flange b, and housing c contact
each other.
a
c b
1
6. Install:
Screws (start switch) 1
WARNING
After tightening the screws, check that the
throttle grip 2 moves smoothly. If it does
not, retighten the screws for adjustment.
2
1
HANDLEBAR

5 - 13
CHASSTEERING AND FRONT SUSPENSION
EC560000
STEERING AND FRONT SUSPENSION
Extent of removal:1 Lower bracket removal
2 Bearing removal
3 Inner table assembly removal
Extent of removal Order Part name Q ’ty Remarks
STEERING AND FRONT SUS-
PENSION REMOVAL
WARNING
Support the machine securely so
there is no danger of it falling over.
Preparation for removal Hold the machine by placing the
suitable stand under the engine.
Front wheel Refer to “FRONT WHEEL AND REAR
WHEEL ” section.
Handlebar Refer to “HANDLEBAR ” section.
1 Cable guide 1
2 Reflector 2 For Canada
3 Steering stem nut 1
4 Upper bracket 1
5 Special washer 1 Use special tool. Refer to “STEERING HEAD INSPEC-
TION AND ADJUSTMENT ” section in
the CHAPTER 3.
6 Upper ring nut 1
7 Rubber washer 1
213

5 - 17
CHASSWINGARM
EC570000
SWINGARM
Extent of removal:1 Swingarm removal
2 Rear shock absorber removal
Extent of removal Order Part name Q ’ty Remarks
SWINGARM REMOVAL
WARNING
Support the machine securely so
there is no danger of it falling over.
Preparation for removal Hold the machine by placing the
suitable stand under the engine.
Seat assembly Refer to “FRONT FENDER, SEAT
ASSEMBLY AND FUEL TANK ” section
in the CHAPTER 4.
Rear wheel Refer to “FRONT WHEEL AND REAR
WHEEL ” section.
Drive chain
1 Rear shock absorber 1
2 Drive chain guard 1
3 Drive chain support 1
4 Drive chain guide 1
1
2