2006 YAMAHA TTR50 height

SPEC
2 - 1
EC200000
SPECIFICATIONS
EC211000
GENERAL SPECIFICATIONS
Model name: TT-R50EV (USA, CDN, AUS, NZ)TT-R50E (Europe, ZA)
Model code number: 1P61 (USA) 1P62 (CDN)
1P63 (Europe, AUS, NZ, ZA)
Dimensions: Overall length 1,305 mm (51.4 in)
Overall width 595 mm (23.4 in)
Overall height 775 mm (30.5 in)
Seat height 555 mm (21.9 in)
Wheelbase 925 mm (36.4 in)
Minimum ground clearance 135 mm (5.31 in)
Dry weight: Without oil and fuel 54.0 kg (119 lb)
Engine: Engine type Air cooled 4-stroke, SOHC
Cylinder arrangement Forward-inclined single cylinder
Displacement 49.5 cm
3 (3.02 cu.in)
Bore × stroke 36.0 × 48.6 mm (1.42 × 1.91 in)
Compression ratio 9.5 : 1
Compression pressure (STD) 1,300 kPa (13 kg/cm
2, 185 psi) at 600 r/min
Starting system Electric starter
Lubrication system: Wet sump
Oil type or grade: Engine oil
(For USA and CDN)
At –10 °C (14 °F) or higher È
Yamalube 4 (10W-30) or SAE 10W-30 type
SE/SF/SG motor oil
At 5 °C (41 °F) or higher É
Yamalube 4 (20W-40) or SAE 20W-40 type
SE/SF/SG motor oil
(Except for USA and CDN)
API “SE/SF/SG ” or higher grade
0 10 30 50 70 90 110 130
-20 -10 0 10
20
30 40 50
È
É
˚F
˚C
GENERAL SPECIFICATIONS

SPEC
2 - 9
Carburetor:
I. D. mark 1P61 00 ----
Main jet (M.J) #62.5 ----
Main nozzle (N.J) E-2M ----
Main air jet (M.A.J) ø 1.4 ----
Jet needle (J.N) 4DL22-1 ----
Cutaway (C.A) 2.5 ----
Pilot outlet (P.O) ø 0.8 × 1.5 ----
Pilot jet (P.J) #12.5 ----
Valve seat size (V.S) ø 1.2 ----
Starter jet 1 (G.S.1) #20 ----
Starter jet 2 (G.S.2) ø 0.6 ----
Float height (F.H) 18.5 mm (0.73 in) ----
Fuel level (F.L) 2.0 ~ 3.0 mm (0.08 ~ 0.12 in) ----
Engine idle speed 1,600 ~ 1,800 r/min ----
Lubrication system: Oil filter type Wire mesh type ----
Oil pump type Trochoid type ----
Inner-rotor-to-outer-rotor-tip clearance 0.15 mm or less (0.0061 in or less)0.20 mm
(0.0079 in)
Outer-rotor-to-oil-pump-housing clearance 0.07 mm (0.0028 in)0.15 mm
(0.0059 in)
Oil-pump-housing-to-inner-rotor-and-outer-
rotor clearance 0.06 ~ 0.10 mm
(0.0024 ~ 0.0039 in)0.17 mm
(0.0067 in)
Item Standard Limit
MAINTENANCE SPECIFICATIONS

4 - 8
ENGCARBURETOR
Float height
1. Measure:Float height a
Out of specification → Adjust.
Float height:
18.5 mm (0.73 in)
Measurement and adjustment steps:
 Hold the carburetor in an upside down
position.
NOTE:
Slowly tilt the carburetor in the opposite
direction, then take the measurement
when the needle valve aligns with the float
arm.
 If the carburetor is level, the weight of the
float will push in the needle valve, resulting
in an incorrect measurement.
 Measure the distance between the mating
surface of the float chamber and top of the
float using a vernier calipers.
NOTE:
The float arm should be resting on the nee-
dle valve, but not compressing the needle
valve.
If the float height is not within specification,
inspect the valve seat and needle valve.
 If either is worn, replace them both.
 If both are fine, adjust the float height by
bending the float tab b on the float.
 Recheck the float height.
a
b
EC464600
Float
1. Inspect:
Float 1
Damage → Replace.
1