2006 YAMAHA MAJESTY 180 warning light

EAU10430
Controls and instruments
DESCRIPTION
2-3
224
21
17
23
22
2619201827
182516
15
28
15. Rear brake lever (page 3-6)
16. Left handlebar switch (page 3-4)
17. Speedometer (page 3-3)
18. Turn indicator lights (page 3-1)
19. High beam indicator light (page 3-1)
20. Coolant temperature warning light (page 3-1)
21. Fuel gauge (page 3-3)22. Front brake lever (page 3-5)
23. Right handlebar switch (page 3-4)
24. Battery voltage (page 3-3)
25. Odometer/Clock (page 3-4)
26. Main switch/Steering lock (page 3-1)
27. Front compartment (page 3-7)
28. Coolant level gauge window (page 6-10)
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 14

EAU10450
Main switch
The main switch controls the ignition
and lighting systems. The various
main switch positions are described
below.
EAU10630
ON
All electrical systems are supplied
with power, and the engine can be
started. The key cannot be removed.
EAU10660
OFF
All electrical systems are off. The key
can be removed.
EAUM1020
“h”
The coolant temperature warning light
should come on when the key is tur-
ned to “h”. (See page 3-2.)
EAU10700
LOCK
The steering is locked, and all electri-
cal systems are off. The key can be
removed.
T
o lock the steering
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF”
position, release it, and then turn
it to “LOCK”.
3. Remove the key.
T
o unlock the steering
Insert the key and turn it to “OFF”.
EWA10060
s s
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is
moving, otherwise the electrical
systems will be switched off, which
may result in loss of control or an
accident. Make sure that the vehi-
cle is stopped before turning the
key to “OFF” or “LOCK”.
EAU10980
Indicator lights
1. Turn signal indicator lights
2. High beam indicator light
121
3
INSTRUMENT AND CONTROL FUNCTIONS
3-1
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 15

EAU11030
Turn signal indicator lights “c” and
“
d”
The corresponding indicator light flas-
hes when the turn signal switch is
pushed to the left or right.
EAU11080
High beam indicator light “j”
This indicator light comes on when
the high beam of the headlight is swit-
ched on.
EAU11390
Oil change indicator light “z”
1. Oil change indicator
2. Coolant temperature warning light
This indicator light comes on at the
initial 1000 km (600 mi) and every
3000 km (1800 mi) thereafter to indi-cate that the engine oil should be
changed.
If the engine oil is changed before the
oil change indicator comes on (i.e.
before the periodic oil change interval
has been reached), the indicator light
must be reset after the oil change for
the next periodic oil change to be
indicated at the correct time. (See
page 6-8.)
The electrical circuit of the indicator
light can be checked according to the
following procedure.
1. Set the engine stop switch to “h”
and turn the key to “ON”.
2. Check that the indicator comes
on for a few seconds and then
goes off.
3. If the indicator light does not
come on, have a Yamaha dealer
check the electrical circuit.
NOTE:
The oil change indicator light may
flash when the engine is revved with
the scooter on the centerstand, but
this does not indicate a malfunction.
EAUM1080
Coolant temperature warning light
“
y”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and
allow the engine to cool.
The electrical circuit of the warning
light can be checked according to the
following procedure.
1. Turn the key to “h”.
2. If the warning light does not
come on, have a Yamaha dealer
check the electrical circuit.
ECA10020
CAUTION
Do not operate the engine if it is
overheated.
12
3
INSTRUMENT AND CONTROL FUNCTIONS
3-2
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 16

EAU20011
Final gear oil
1. Oil filler cap
The final gear case must be checked
for oil leakage before each ride. If any
leakage is found, have a Yamaha dea-
ler check and repair the vehicle. In
addition, the final gear oil must be
changed as follows at the intervals
specified in the periodic maintenance
and lubrication chart.
EWA10370
s s
WARNING
Make sure that no foreign
material enters the final gear
case.
Make sure that no oil gets on
the tire or wheel.
To check the final gear oil level
1. Place the vehicle on the centers-
tand.
1. Drain bolt
NOTE:
The final gear oil level must be
checked on a cold engine.
Make sure that the vehicle is posi-
tioned straight up when checking
the oil level. A slight tilt to the side
can result in a false reading.
2. Remove the oil filler bolt, and
then check the oil level in the final
gear case.
NOTE:
The oil level should be at the brim of
the filler hole.
3. If the oil is below the brim of the
filler hole, add sufficient oil of the
recommended type to raise it to
the correct level.
4. Install the oil filler bolt, and then
tighten it to the specified torque.
To change the final gear oil
1. Place an oil pan under the final
gear case to collect the used oil.
2. Remove the oil filler bolt and
drain bolt to drain the oil from the
final gear case.
3. Install the final gear oil drain bolt,
and then tighten it to the speci-
fied torque.
Tightening torque:
Final gear oil filler bolt:
22 Nm (2,2 m•kgf, 15,91 ft•lbf)
1
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 38

ECA10600
CAUTION
If the breather hose is positioned in
such a way that the frame is expo-
sed to electrolyte or gas expelled
from the battery, the frame could
suffer structural and external
damages.
EAUS1180
Replacing the fuse
1. Main fuse
The fuse holder is located beside the
battery case.
If the fuse is blown, replace it as
follows.1. Turn the key to “OFF” and turn off
all electrical circuits.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
ECA10640
CAUTION
Do not use a fuse of a higher ampe-
rage rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.
3. Turn the key to “ON” and turn on
the electrical circuits to check if
the devices operate.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
EAUS1110
Replacing the headlight bulb
or a front turn signal light
bulb
If a bulb burns out, replace it as
follows.
ECA10670
CAUTION
It is advisable to have a Yamaha
dealer perform this job.
Headlight bulb
1. Remove the front panel by remo-
ving the screws.
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
2. Remove the defective bulb from
the socket.
3. Insert a new bulb into the socket.
Specified fuse:
20 A
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-20
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 49

Rear tireType
Tubeless
Size
130/70-12 51L
Manufacturer/model
MICHELIN
GHENG SING
PIRELLI
LoadingMaximum load
183 kg
183 kg
Tire air pressure (measured on cold
tires)
Front
190 kPa
Rear
220 kPa
Front wheelWheel type
Cast wheel
Rim size
12 x MT3.50
Rear wheelWheel type
Cast wheel
Rim size
12 x MT3.50
Front brakeType
Single disc brake
Operation
Right hand operationRecommended fluid
DOT 4
Rear brakeType
Single disc brake
Operation
Left hand operation
Recommended fluid
DOT 4
Front suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
90.0 mm
Rear suspensionType
Unit swing
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
90 mm
Electrical systemIgnition system
CDI
Charging system
AC magneto
BatteryModel
CB7L-B2
Voltage, capacity
12 V, 8 Ah
Bulb voltage, wattage x quantityHeadlight
12 V, 35 W / 35 W x 2
Tail/brake light
12 V, 21 W / 5 W x 2
Front turn signal light
12 V, 21 W x 2
Rear turn signal light
12 V, 10 W x 2
Meter lighting
12 V, 1.2 W x 2
High beam indicator light
12 V, 1.2 W x 1
Oil level warning light
LED
Fuel level warning light
NONE
FusesMain fuse
20 A
Radiator fan fuse
4 A
Reserve fuse
20 A
Reserve fuse
4 A
8
SPECIFICATIONS
8-2
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 59