2006 YAMAHA DT125R wheel torque

EAU22960
To adjust the drive chain slack
1. Axle nut
2. Chain tensioner
1. Loosen the axle nut.
2. To tighten the drive chain, turn
the adjusting plate on each side
of the swingarm in direction (a).
To loosen the drive chain, turn
the adjusting plate on each side
of the swingarm in direction (b),
and then push the rear wheel for-
ward.
NOTE:
Make sure that both adjusting plates
are in the same position for proper
wheel alignment.
ECA10570
CAUTION
Improper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.
3. Tighten the axle nut to the speci-
fied torque.
Tightening torque:
Axle nut:
90 Nm (9,0 m•kgf)
EAU23021
Lubricating the drive chain
The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly
wear out, especially when riding in
dusty or wet areas. Service the drive
chain as follows.
ECA10581
CAUTION
The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.
1. Clean the drive chain with kero-
sene and a small soft brush.
ECA11120
CAUTION
To prevent damaging the O-rings,
do not clean the drive chain with
steam cleaners, high-pressure
washers or inappropriate solvents.
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant.
ECA11110
CAUTION
Do not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-20
1 2
1D0-F8199-E2.qxd 20/9/04 11:32 Página 51

EWA10820
s s
WARNING
It is advisable to have a Yama-
ha dealer service the wheel.
Securely support the motorcy-
cle so that there is no danger of
it falling over.
1. Disconnect the speedometer
cable from the front wheel.
2. Loosen the wheel axle holder
nuts, then the wheel axle.
3. Lift the front wheel off the ground
according to the procedure on
page 6-26.
4. Pull the wheel axle out, and then
remove the wheel.
ECA11070
CAUTION
Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
EAU24950
To install the front wheel
1. Install the speedometer gear unit
into the wheel hub so that the
projections mesh with the slots.
2. Lift the wheel up between the
fork legs.
NOTE:
Make sure that there is enough space
between the brake pads before inser-
ting the brake disc and that the slot in
the speedometer gear unit fits over
the retainer on the fork leg.
3. Insert the wheel axle.
4. Lower the front wheel so that it is
on the ground.
5. Tighten the wheel axle to the
specified torque.
Tightening torque:
Wheel axle:
55 Nm (5,5 m•kgf)
6. Tighten the axle holder nuts to
the specified tightening torque. Tigh-
ten the upper nuts first and then lower
ones. When tightened in this sequen-
ce, there should be a gap formed at
the bottom of the axle holder.
Tightening torque:
Axle holder nut:
10 Nm (1,0 m•kgf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-27
1D0-F8199-E2.qxd 20/9/04 11:32 Página 58

ECA11070
CAUTION
Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
EAU25530
To install the rear wheel
1. Install the drive chain onto the
rear sprocket, and then insert the
wheel axle from the left-hand
side.
NOTE:
Make sure that there is enough space
between the brake pads before inser-
ting the brake disc between the brake
pads.
2. Install the drive chain adjusting
plates.
NOTE:
Make sure that the drive chain adjus-
ting plates are installed with the pun-
ched side facing to the outside.
3. Install the swingarm end bolts.4. Adjust the drive chain slack. (See
page 6-19.)
5. Tighten the axle nut and the
swingarm end bolts to the speci-
fied torques, and then install the
cotter pin.
EWA10700
s s
WARNING
Always use a new cotter pin for the
axle nut.
Tightening torque:
Axle nut:
90 Nm (9,0 m•kgf)
Swingarm end bolt:
3 Nm (0,3 m•kgf)
EAU25850
Troubleshooting
Although Yamaha motorcycles recei-
ve a thorough inspection before ship-
ment from the factory, trouble may
occur during operation. Any problem
in the fuel, compression, or ignition
systems, for example, can cause poor
starting and loss of power.The following troubleshooting chart
represents a quick and easy procedu-
re for checking these vital systems
yourself. However, should your
motorcycle require any repair, take it
to a Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the motorcycle properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-29
1D0-F8199-E2.qxd 20/9/04 11:32 Página 60