2006 YAMAHA BANSHEE 350 torque

8-65
7. Tighten the carburetor cap securing plate
screw to the specified torque.
8. Tighten the carburetor joint screws.
Adjusting the throttle cables
NOTE:
After the jet needle clip position is changed, the
throttle cables may need to be adjusted.
1. Move the throttle lever a few times.
2. Push the throttle lever forward until it stops
and hold it in this position.
3. Check through each carburetor window to
see if the punch mark on the throttle valve
is at the specified position.
4. If not, loosen the locknut and turn the
adjusting nut until the specified position is
obtained.
5. Move the throttle lever a few times and
recheck the position.
6. Install the fuel tank, side cover, radiator
cover and air filter case cover.
7. Connect the fuel hoses.
8. Install the seat.
a
1
wq
1. Punch mark a. Specified position : 0–1mm
1. Poinçonné a. Position spésifiée : 0 à 1mm
1. Marca de punzón a.Posición especificada : 0–1mm
1. Locknut (×2) 2. Adjusting nut (×2)
1. Contre-écrou (×2) 2. Écrou de réglage (×2)
1. Tuerca de bloqueo (×2) 2. Tuerca de tensor (×2)
Tightening torque:
3.5 Nm (0.35 m0kgf)

8-87
5. Screw in the adjusting bolt at the rear brake
caliper by hand until it feels tight, then screw
it out 1/8 turn. Tighten the locknut to the
specified torque.
cC
When tightening the locknut, hold the adjust-
ing bolt with a wrench so that the adjusting
bolt does not turn together with the locknut.
w
Operating with improperly adjusted brakes
could cause the brakes to malfunction,
resulting in reduced braking performance.
This could increase the chance of a collision
or accident. After adjusting the parking
brake, block the rear of the machine off the
ground and spin the rear wheels. Check to
make sure there is no brake drag. If brake
drag is noticed, perform the adjustment
again.
qw
1. Ajusting bolt 2. Locknut
1. Boulon de réglage 2. Contre-écrou
1. Perno de ajuste 2. Contratuerca
Tightening torque:
Locknut:
16 Nm (1.6 m0kgf)

8-105
EBU01112
Wheel removal
1. Loosen the wheel nuts.
2. Elevate the ATV and place a suitable stand
under the frame.
3. Remove the nuts from the wheel.
4. Remove the wheel.
EBU00871
Wheel installation
When installing the wheel, reverse the removal
procedure.
Tighten the wheel nuts to the specified torques.
Front
Avant
Delantera
Rear
Arrière
Trasera
Tightening torque:
Wheel nut:
Front: 45 Nm (4.5 m0kgf)
Rear: 45 Nm (4.5 m0kgf)

All specification data in this manual are listed in SI
and METRIC UNITS.
Use this table to convert METRIC unit values to
IMPERIAL unit values.
Example:
METRIC
VALUECONVERSION
FACTORIMPERIAL
VALUE
2 mm× 0.03937 = 0.08 in
Conversion table
METRIC SYSTEM TO IMPERIAL SYSTEM
Metric unitConversion
factorImperial unit
Torquem·kgf
m·kgf
cm·kgf
cm·kgf
×7.233×86.794
×0.0723×0.8679ft·lbf
in·lbf
ft·lbf
in·lbf
Weightkg
g
×2.205×0.03527lb
oz
Speed km/h
×0.6214 mi/h
Distancekm
m
m
cm
mm
×0.6214
×3.281
×1.094×0.3937×0.03937mi
ft
yd
in
in
Volume,
Capacitycc (cm3)
cc (cm3)
L (liter)
L (liter)
×0.03527
×0.06102
×0.8799×0.2199oz (IMP liq.)
cu·in
qt (IMP liq.)
gal (IMP liq.)
Miscellaneouskg/mm
kgf/cm
2
°C
×55.997×14.2234
×1.8 + 32 lb/in
psi (lbf/in
2)
°F
11-1
EBU01070
Conversion table