Page 81 of 211
73
Nylon cargo net (XC70 with 3-section rear seat)
Nylon cargo net (option on
XC70)
6J5.2
•
•
•(
,
1
/,
1
(>
WARNING!
8
4
•If the net is installed in the forward
position and the rear seat cushions are
folded forward, the net should be posi-
tioned so that it is in front of the rear seat
cushions but behind the front seat
backrests (C).
•The eyelets on the floor of the car under
the front seats must not be used to secure
the lower straps of the cargo net. If these
eyelets are used and the front seats are
moved back, the cargo net or upper
brackets may be damaged.
Folding and storing the cargo
net
8
Press the buttons on the hinges at the center of
the upper and lower rods. This releases the
hinges so that the net can be folded.
8901984m8901980m
+ #
/
Page 83 of 211
75
Spare tire
7700313m
Jack
Tool bag
Securing
bracket
Spare tire
8503191m
1
Spare tire
>
#
•"
8
0 ,%F
1
•=
,1
•=
>
•=
•4
7
>
Spare tire, tool bag, jack - cars with
subwoofer (option)
>
#
•"
8
0 ,%F
1
•"
•"
•G
32O
•G
•=
>
•=
•4
7
>
WARNING!
7
>
Page 113 of 211
105
Emergency towing
Front towing eyelet Rear towing eyelet
Emergency towing
The towing eyelet is located in the tool bag,
under the floor of the cargo area, with the
spare tire. This eyelet must be screwed into the
positions provided on the right sides of either
the front or rear bumper (see illustration). To
attach the towing eyelet:
•=
,(1
•)
,<1
After the car has been towed, the eyelet should
be removed and returned to the tool bag. Press
the cover back into position.
Precautions when the car is
in tow
•
•
•7
8 #F2 ,&2$ 1
•7
8
#F2 ,&21
•4
•5
CAUTION:
•Please check with state and local authori-
ties before attempting this type of towing,
as vehicles being towed are subject to
regulations regarding maximum towing
speed, length and type of towing device,
lighting, etc.
•If the car’s battery is dead, do not attempt
to start the vehicle by pushing or pulling it
as this will damage the three-way catalytic
converter(s). The engine must be jump
started using an auxiliary battery (see page
109).
•If the car is being towed on a flat bed
truck, the towing eyelets must not be used
to secure the car on the flat bed. Consult
the tow truck operator.
WARNING!
•Remember that the power brakes and
power steering will not function when
engine is not running. The braking and
steering systems will function but the
brake pedal pressure required is 3 - 4
times above normal and greater steering
effort must be exerted.
•The towing eyelets must not be used for
pulling another vehicle out of a ditch or
for any similar purpose involving severe
strain.
•Do not use the towing eyelets to pull the
car up onto a flat bed tow truck.
A
B
C
8600422M
Page 114 of 211
106
Vehicle towing information
Towing cars with all wheel drive/front wheel
drive
Volvo recommends the use of flat bed equipment.
If wheel lift equipment must be used, please use extreme caution to help
avoid damage to the car. In this case, the car should be towed with
the rear wheels on the ground if at all possible.
If it is absolutely necessary to tow the vehicle with the front wheels on
the ground, please refer to the towing information on the previous page.CAUTION:
•The car must not be driven with wheels of different dimensions/
specifications or with a spare tire other than the one that came with
the car. The use of different size wheels can seriously damage your
car's transmission.
•Sling-type equipment applied at the front will damage radiator and
air conditioning lines.
•It is equally important not to use sling-type equipment at the rear or
apply lifting equipment inside the rear wheels; serious damage to
the rear axle may result.
•If the car is being towed on a flat bed truck, the towing eyelets must
not be used to secure the car on the flat bed. Consult the tow truck
operator.
'
8101937m
Page 172 of 211
164
Replacing wiper blades
Headlight wiper blades
(certain models)
9
9
5
Replacement of tailgate wiper
blade
Pull the wiper arm out away from the glass.
Pull off the wiper blade outwards toward the
tailgate. Press the new wiper blade into place.
Check that it is properly secured.
3602076DShort Long
Windshield wiper blades
•G
•9
,(
1
•9
•
C
C
A
A
Page 201 of 211
193 5
During programming, your hand-held transmitter may automatically stop
transmitting. To successfully train HomeLink®, continue to hold the
HomeLink® button. At the same time, repeatedly press and hold your
hand-held transmitter’s button at two-second intervals until HomeLink®
has learned your transmitter’s code. The HomeLink® indicator light
will flash first slowly, and then rapidly to indicate that the button has
been successfully programmed.
Determining if your garage door uses a rolling code
Determine, in one of the following ways, if your garage door uses a
rolling code system and is manufactured after 1996:
•"
C
•
GY
=
•9
GY
GY
8
*
To train a rolling code garage door opener, follow these instructions
after programming the desired transceiver button according to “Program-
ming the transceiver.” The help of a second person may make training
easier.
%
G
,$
C
% &22 -FF -F%F , #
G
1
*
9 :
;
:
;
-
9
GY
9
GY
)
$
GY=
The remaining two HomeLink® buttons can be programmed in the
same way. In the event of any problems in programming the
HomeLink® Universal Transceiver, call toll-free 1-800-355-3515
(Internet: www.HomeLink.com).
Operating the HomeLink® Universal Transceiver
Once programmed, the HomeLink® Universal Transceiver can be used
in place of your hand-held transmitters.
To operate, the key must be turned to the “accessory” position (II) or
the engine must be running. Press the programmed HomeLink® button
to activate the garage door, driveway gate, security lighting, home
security system, etc.
Your original hand-held transmitters may, of course, be used at any
time.
Erasing programmed buttons
Individual buttons cannot be erased. To erase all three programmed
buttons:
%
:
; ,1
*
GY=
*2 GYC
-
"
The HomeLink® buttons can be reprogrammed using the procedures
described on the previous page.
,GY
8
1
HomeLink® Universal Transceiver (option)
