2006 TOYOTA xA tow
[x] Cancel search: towPage 3 of 23
INTRODUCTIONCongratulations on your choice of the xA remote keyless security system to protect your vehicle! To
get the most from the system, we strongly recommend that you read this Owner’s Guide completely
to learn all of its features and functions.
The xA Security with RKE provides the convenience of remote keyless operation, enabling you to
ARM
and D
ISARM
at the same time you remotely lock and unlock the doors. The system provides
comprehensive security protection through point-of-entry monitoring, intrusion detection and ignition
switch monitoring. While A
RMED
, the system will be T
RIGGERED
and sound an A
LARM
when a door is
forcibly unlocked or opened*, or when movement occurs inside the vehicle. During the A
LARM
, the
vehicle’s horn sounds and the headlights, tail lights and front marker lights flash.Also, the vehicle’s
starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUS
MONITOR
for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) .
About the ignition-controlled automatic door locking/unlocking function.
The xA Security with RKE is programmed to automatically lock your vehicle’s doors when you turn
the key in the ignition switch to the “ON” or “START” position, and unlock them when you turn the
key back to the “ACC” or “LOCK” position. You may disable this feature by reprogramming the sys-
tem; refer to page 18 for programming information.
*When the system is P
ASSIVELY
(AUTOMATICALLY
) A
RMED
, there is an E
NTRY
DELAY
that will
elapse when a door is opened before an A
LARM
is T
RIGGERED
.
LIGHTS FOR30 SECONDS(PRE-ARMING
)
THEN STARTS
FLASHING(SYSTEM IS
ARMED
)
Page 2
SCION
SCION
Page 19
SCIONSECURITY
REMOTE CONTROL BATTERY REPLACEMENTThe following shows the procedure to replace the batteries in your remote controls. We recommend
that you replace the batteries at least once a year, or when the remote control’s transmitting range
diminishes. You may obtain the replacement battery from your Scion dealer, as well as many retail-
ers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5.Push the battery down and toward you, and hold it
down.
6. Pry the back edge of the battery up and toward you.
SCION
SECURITY
1
2
1
2
Page 7 of 23
PROGRAMMINGPASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTIONThe xA Security with RKE is factory-set to not P
ASSIVELY
ARM. To change the system’s operation for
P
ASSIVE
ARMING
operation, as well as adjust the E
NTRY
DELAY
time, follow the procedure below. For
more information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure.(Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATIONARMING THE xA SECURITY WITH RKE (except PASSIVE ARMING)The system may be A
RMED
in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
* The system will not A
RM
while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6
SCION
SCION
Page 15
SCIONSECURITYTURN TOWARD THE FRONT
OF THE VEHICLEPRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
LIGHTS FOR30 SECONDS(PRE-ARM
-
ING)THEN
FLASHES(SYSTEM IS
ARMED
)
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times.b. Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.a. Close, then Open the door:
2 times = P
ASSIVE
ARMING
OFF
3 times = P
ASSIVE
ARMING
ON,
0 Sec. E
NTRY
DELAY
4 times = P
ASSIVE
ARMING
ON,
15 Sec. E
NTRY
DELAY
5 times = P
ASSIVE
ARMING
ON,
30 Sec. E
NTRY
DELAY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d.The system locks the door
in 2 seconds; if this does
not happen, start over.
c.The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete. e. Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS
REMOTE ARMED
1
2
31112
3
3
Page 8 of 23
OPERATIONDISARMING THE xA SECURITY WITH RKE (except PASSIVE DISARMING)The system may be D
ISARMED
in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the driver’s door key switch and turn it toward the
rear of the vehicle:
The S
TATUS
MONITOR
’SLED stops flashing. The system
is now D
ISARMED
.*
In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARM
will be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The interior lights turn on for 30 seconds.
The S
TATUS
MONITOR
’SLED stops flashing. The system is
now D
ISARMED
.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.
Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The S
TATUS
MONITOR
’SLED stops flashing. The system
is now D
ISARMED
.
This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.
NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED
, the T
RIGGER
MEMORY
was activated; an A
LARM
was
T
RIGGERED
while you were away from the vehicle.
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE
-
RIOR LIGHTS TURN ON FOR
30 SECONDS WHEN THE SYSTEM
IS REMOTE DISARMED
Page 14
SCION
SCION
Page 7
SCIONSECURITYTURN TOWARD THE REAR
OF THE VEHICLETURN THE KEY TO
“ON” TO
DISARM THE SYSTEM
THE DRIVER
’SDOOR UNLOCKS
WHEN THE SYSTEM IS REMOTE
DISARMED
PUSH THE UNLOCK BUTTON
STOPS
FLASHING
WHEN THE
SYSTEM IS
DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS
REMOTE DISARMED
RADAR SENSOR INFORMATIONRADAR SENSOR CHECK PROCEDURE
1. A
RM
the system.
Press the LOCK button on the remote control or lock the doors
with the key.
(Remember, the system will not ARM if any door is open.)
2. Wait until the S
TATUS
MONITOR’S
LED starts flashing.
The LED will flash 30 seconds after the last door or hatch is closed.
3. Move inside the vehicle.
When movement occurs inside the vehicle, an alarm will be triggered
immediately. If sensor detects 2nd movement within 60 seconds after
the 1st warn away alarm trigger, then a regular ALARM activates for 60
seconds.
Note: If you find that the system does not perform as expected, contact
your Toyota dealer for more information.
4. D
ISARM
the system to stop the A
LARM
.
Press the UNLOCK button on the remote control or use the key to
DISARM the system.
RADAR SENSOR OFF MODETHE RADAR SENSOR CAN BE DEACTIVATED. PERFORM THE FOLLOWING:
1. Open the driver’s door .
The LED turns off. The system is now DISARMED.
2. Lock, then unlock the driver’s door inside lock button 3 times,
within 5 seconds.
The LED flash quickly.
3. Close the driver’s door.
4. ARM
THE SYSTEM WITH THE REMOTE CONTROL OR KEY WHILE THE
LED
IS
BLINKING
.THE RADAR SENSOR
WILL DEACTIVATE DURING ARMING.
NOTE: I
F YOU DISARM THE SYSTEM AFTER YOU SET THE RADAR SENSOROFF
, YOU HAVE TO REPEAT THE ABOVE PROCEDURE WHEN YOU ARM
THE SYSTEM IF YOU WANT TO DEACTIVATE THE RADAR SENSOR AGAIN.
THE SYSTEM WILL AUTOMATICALLY CANCEL THE RADAR SENSOR OFF
MODE WHEN DISARMED.
SCIONSECURITY
1
You must disarm the system before opening the hatch, or else the Alarm will
be triggered.
2
3
311
1
2
3
Page 15 of 23
OPERATIONDISARMING THE xA SECURITY WITH RKE (except PASSIVE DISARMING)The system may be D
ISARMED
in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the driver’s door key switch and turn it toward the
rear of the vehicle:
The S
TATUS
MONITOR
’SLED stops flashing. The system
is now D
ISARMED
.*
In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARM
will be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The interior lights turn on for 30 seconds.
The S
TATUS
MONITOR
’SLED stops flashing. The system is
now D
ISARMED
.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.
Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The S
TATUS
MONITOR
’SLED stops flashing. The system
is now D
ISARMED
.
This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.
NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED
, the T
RIGGER
MEMORY
was activated; an A
LARM
was
T
RIGGERED
while you were away from the vehicle.
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE
-
RIOR LIGHTS TURN ON FOR
30 SECONDS WHEN THE SYSTEM
IS REMOTE DISARMED
Page 14
SCION
SCION
Page 7
SCIONSECURITYTURN TOWARD THE REAR
OF THE VEHICLETURN THE KEY TO
“ON” TO
DISARM THE SYSTEM
THE DRIVER
’SDOOR UNLOCKS
WHEN THE SYSTEM IS REMOTE
DISARMED
PUSH THE UNLOCK BUTTON
STOPS
FLASHING
WHEN THE
SYSTEM IS
DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS
REMOTE DISARMED
RADAR SENSOR INFORMATIONRADAR SENSOR CHECK PROCEDURE
1. A
RM
the system.
Press the LOCK button on the remote control or lock the doors
with the key.
(Remember, the system will not ARM if any door is open.)
2. Wait until the S
TATUS
MONITOR’S
LED starts flashing.
The LED will flash 30 seconds after the last door or hatch is closed.
3. Move inside the vehicle.
When movement occurs inside the vehicle, an alarm will be triggered
immediately. If sensor detects 2nd movement within 60 seconds after
the 1st warn away alarm trigger, then a regular ALARM activates for 60
seconds.
Note: If you find that the system does not perform as expected, contact
your Toyota dealer for more information.
4. D
ISARM
the system to stop the A
LARM
.
Press the UNLOCK button on the remote control or use the key to
DISARM the system.
RADAR SENSOR OFF MODETHE RADAR SENSOR CAN BE DEACTIVATED. PERFORM THE FOLLOWING:
1. Open the driver’s door .
The LED turns off. The system is now DISARMED.
2. Lock, then unlock the driver’s door inside lock button 3 times,
within 5 seconds.
The LED flash quickly.
3. Close the driver’s door.
4. ARM
THE SYSTEM WITH THE REMOTE CONTROL OR KEY WHILE THE
LED
IS
BLINKING
.THE RADAR SENSOR
WILL DEACTIVATE DURING ARMING.
NOTE: I
F YOU DISARM THE SYSTEM AFTER YOU SET THE RADAR SENSOROFF
, YOU HAVE TO REPEAT THE ABOVE PROCEDURE WHEN YOU ARM
THE SYSTEM IF YOU WANT TO DEACTIVATE THE RADAR SENSOR AGAIN.
THE SYSTEM WILL AUTOMATICALLY CANCEL THE RADAR SENSOR OFF
MODE WHEN DISARMED.
SCIONSECURITY
1
You must disarm the system before opening the hatch, or else the Alarm will
be triggered.
2
3
311
1
2
3
Page 16 of 23
PROGRAMMINGPASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTIONThe xA Security with RKE is factory-set to not P
ASSIVELY
ARM. To change the system’s operation for
P
ASSIVE
ARMING
operation, as well as adjust the E
NTRY
DELAY
time, follow the procedure below. For
more information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure.(Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATIONARMING THE xA SECURITY WITH RKE (except PASSIVE ARMING)The system may be A
RMED
in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
* The system will not A
RM
while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6
SCION
SCION
Page 15
SCIONSECURITYTURN TOWARD THE FRONT
OF THE VEHICLEPRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
LIGHTS FOR30 SECONDS(PRE-ARM
-
ING)THEN
FLASHES(SYSTEM IS
ARMED
)
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times.b. Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.a. Close, then Open the door:
2 times = P
ASSIVE
ARMING
OFF
3 times = P
ASSIVE
ARMING
ON,
0 Sec. E
NTRY
DELAY
4 times = P
ASSIVE
ARMING
ON,
15 Sec. E
NTRY
DELAY
5 times = P
ASSIVE
ARMING
ON,
30 Sec. E
NTRY
DELAY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d.The system locks the door
in 2 seconds; if this does
not happen, start over.
c.The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete. e. Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS
REMOTE ARMED
1
2
31112
3
3
Page 20 of 23
INTRODUCTIONCongratulations on your choice of the xA remote keyless security system to protect your vehicle! To
get the most from the system, we strongly recommend that you read this Owner’s Guide completely
to learn all of its features and functions.
The xA Security with RKE provides the convenience of remote keyless operation, enabling you to
ARM
and D
ISARM
at the same time you remotely lock and unlock the doors. The system provides
comprehensive security protection through point-of-entry monitoring, intrusion detection and ignition
switch monitoring. While A
RMED
, the system will be T
RIGGERED
and sound an A
LARM
when a door is
forcibly unlocked or opened*, or when movement occurs inside the vehicle. During the A
LARM
, the
vehicle’s horn sounds and the headlights, tail lights and front marker lights flash.Also, the vehicle’s
starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUS
MONITOR
for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) .
About the ignition-controlled automatic door locking/unlocking function.
The xA Security with RKE is programmed to automatically lock your vehicle’s doors when you turn
the key in the ignition switch to the “ON” or “START” position, and unlock them when you turn the
key back to the “ACC” or “LOCK” position. You may disable this feature by reprogramming the sys-
tem; refer to page 18 for programming information.
*When the system is P
ASSIVELY
(AUTOMATICALLY
) A
RMED
, there is an E
NTRY
DELAY
that will
elapse when a door is opened before an A
LARM
is T
RIGGERED
.
LIGHTS FOR30 SECONDS(PRE-ARMING
)
THEN STARTS
FLASHING(SYSTEM IS
ARMED
)
Page 2
SCION
SCION
Page 19
SCIONSECURITY
REMOTE CONTROL BATTERY REPLACEMENTThe following shows the procedure to replace the batteries in your remote controls. We recommend
that you replace the batteries at least once a year, or when the remote control’s transmitting range
diminishes. You may obtain the replacement battery from your Scion dealer, as well as many retail-
ers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5.Push the battery down and toward you, and hold it
down.
6. Pry the back edge of the battery up and toward you.
SCION
SECURITY
1
2
1
2